ECX SPEED 10 M ∅ 10 mm, brushless, BLDC motor High Power Key Data: 8/10.7 W, 1.8 mNm, 65 000 rpm
M 3:2
Motor data Nominal voltage No load speed No load current Nominal speed Nominal torque
1_ 2_ 3_ 4_ 5_ 6_ 7_ 8_ 9_
V
9 36 59400 59500 58800 169 84.5 41.5 52300 53400 52800 1.83 1.85 1.83 1.44 0.728 0.356 15.6 18.5 18.4 11 6.5 3.19 77 79 79 0.82 2.77 11.3 0.00599 0.0239 0.0982 1.42 2.85 5.77 6700 3350 1650 3860 3260 3230 2.4 2.03 2.01 0.0594 0.0594 0.0594 18
rpm mA rpm mNm mNm A A
Nominal current (max. continuous current)
Stall torque Stall current Max. efficiency Terminal resistance Terminal inductance Torque constant Speed constant Speed/torque gradient Mechanical time constant
% Ω
10_ 11_ 12_ 13_ 14_ 15_ 16_ 17_ 18_ 19_ 20_ 21_ 22_ 23_ 24_ 25_ 26_ 27_ 28_ 29_ 30_ 31_ 32_
mH
mNm/A rpm/V rpm/mNm
ms gcm2
Rotor inertia Thermal data
Operating range n [rpm] winding 36 V
Thermal resistance housing-ambient Thermal resistance winding-housing Thermal time constant winding Thermal time constant motor Ambient temperature Max. winding temperature Mechanical data ball bearings Max. speed
K/W K/W
39.8 4.43 2.05 178 -20…+100 155
s s
°C °C
rpm mm
65 000 0…0.14 0.5
Axial play Preload Radial play Direction of force
N
Continuous operation Continuous operation with reduced thermal resistance Rth2 50% Short term operation
pull
0.5 5.9 400 4.7 [5] 1 3 12 55 [50 000] preloaded
Max. axial load (dynamic) Max. force for press fits (static) (static, shaft supported) Max. radial load [mm from flange]
N N N N
M [mNm]
.
.
.
. . .
334_GPX 10 A 335_GPX 12 A/C 336_GPX 12 LN/LZ 337_GPX 12 HP Gearheads Modular system
Details on catalog page 52
Other specifications Number of pole pairs Number of phases Weight of motor Typical noise level [rpm]
Sensors
443_DEC Module 24/2 443_DEC Module 50/5 447_ESCON2 Nano 24/2 455_EPOS4 Module 24/1.5 455_EPOS4 Module 50/5 457_EPOS4 Compact 24/1.5 458_EPOS4 Compact 50/5 Control Electronics
Stages [opt.]
1–5 1–4 1–4 2–4
414_ENX 10 MAG INT
g
dBA
Connection flexprint cable (FPC) Pin 1 Vcc 3.3…6.0 V Pin 2 Hall sensor 3 Pin 3 Hall sensor 1 Pin 4 Hall sensor 2 Pin 5 GND
Configuration
Pin 6 Motor winding 3 Pin 7 Motor winding 2 Pin 8 Motor winding 1 Output signals: CMOS compatible push-pull stage Signal voltage, high: 3.3 V Hall signals are generated by the MAG sensor. Possible matching connectors for the FPC connection: 11-pole, 1.0 mm pitch, e.g., Molex 52207-1185 Available maxon adapter connectors: 220300, 418719
Front flange: center thread/without thread Shaft, front: length/diameter
maxon 147
© 2026 maxon. All rights reserved. April edition. Provisional data. Subject to change.
Made with FlippingBook Publishing Software