EC 45 flat ∅ 43.5 mm, brushless, 70 watt
M 1:2
Stock program Standard program Special program (on request)
Part Numbers
V1 with Hall sensors V2 with Hall sensors and cables
651614 651618
651617
651615 651619
651616
651620 651621
Motor Data (provisional) Values at nominal voltage 1 Nominal voltage
24
36
48
60 57 3720 3010 143 0.92 1240 84.2 8 7.370 4.270 152 62.8 3.040 5.770 181
V
5600 270 4750 134 3.29 1690 84.9 42 0.573 0.301 40.4 236 3.350 6.350 181
5930 198 5080 110 1.97 1320 82.7 23 1.560 0.601 57 167 4.580 8.680 181
5580 135 4750 112 1.41 1260 82.6 16 3.070 1.210 80.8 118 4.490 8.510 181
2 No load speed 3 No load current 4 Nominal speed 5 Nominal torque 7 Stall torque1 8 Stall current 9 Max. efficiency
rpm mA rpm mNm mNm A A
6 Nominal current (max. continuous current)
%
Characteristics 10 Terminal resistance phase to phase 11 Terminal inductance phase to phase
Ω
mH
12 Torque constant 13 Speed constant 14 Speed/torque gradient 15 Mechanical time constant
mNm/A rpm/V rpm/mNm
ms gcm2
Specifications 16 Rotor inertia
Operating Range
Comments
Thermal data 17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing
n [rpm]
Continuous operation In observation of above listed thermal resistance (lines 17 and 18) and an ambient temperature of 25°C, the maximum permissible winding temperature will be reached during continuous operation = thermal limit. Short term operation The motor may be briefly overloaded (recurring). Assigned power rating
2.55 K/W 6.64 K/W
19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature Mechanical data (preloaded ball bearings) 23 Max. speed
43.1 s 127 s
0 2000 4000 6000 8000 10000 12000
70 W
-40…+100°C +125°C 10 000 rpm 0 mm 0.14 mm preloaded
651614
24 Axial play at axial load 25 Radial play
< 8.0 N > 8.0 N
26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange Other specifications 29 Number of pole pairs 30 Number of phases 31 Weight of motor Values listed in the table are nominal. Connection V1
7.2 N 53 N 1000 N 15.1 N
M [mNm] I [A]
0
50 1.4
100 2.6
150 3.8
0.25
8 3
Modular System
Details on catalog page 54
150.4 g
Gear 441_GP 32 A 445_GP 32 C 454_GP 42 C 456_GS 45 A
Motor Control 547_DEC Module 50/5 551_ESCON 36/3 EC 551_ESCON Module 50/5 553_ESCON 50/5 553_ESCON 70/10 561_EPOS4 Micro 24/5 562_EPOS4 Module 50/5 565_EPOS4 Compact 50/5 567_EPOS4 50/5 568_EPOS4 Disk 60/8
Sensor 529_Encoder MILE
V2 (sensors, AWG 24) Hall sensor 1* Hall sensor 2*
Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 1 Pin 2 Pin 3 Pin 4
Hall sensor 1* Hall sensor 2* Motor winding 3 Hall sensor 3* Motor winding 1 Motor winding 2 GND
V Hall 3.5…24 VDC Hall sensor 3*
GND N.C.
V Hall 3.5…24 VDC
V2 (motor, AWG 22) Motor winding 1 Motor winding 2 Motor winding 3
N.C.
*Internal pull-up (7…13 k W ) on V Hall Wiring diagram for Hall sensors see p. 67 Connector Part number Part number Molex 39-28-1083 43025-0600 Molex 39-01-2040
324 maxon EC motor 21 V2 Ambient temperature Connection cable for V1 Universal, L = 500 mm to EPOS, L = 500 mm
339380 354045
-20...+100°C
1 Calculation does not include saturation effect (p. 81/188)
© 2024 maxon. All rights reserved. June edition. Subject to change.
Made with FlippingBook Publishing Software