IDX 70 M 70 mm, with integrated electronics IP65 Drive with Positioning/Speed Controller Key Data: 650/773 W, 2441 mNm, 4000 rpm
M 1:3
Drive data (provisional) Nominal power supply voltage Nominal speed Nominal torque at 25°C Nominal torque at 40°C Nominal supply current at 25°C Nominal supply current at 40°C Maximum speed at nominal voltage Maximum permissible drive speed Maximum torque (short-time) Maximum supply current (short-time) Rotor inertia of the drive Nominal supply voltage + V CC Mechanical time constant Thermal resistance housing-ambient Thermal resistance winding-housing Thermal time constant winding Thermal time constant drive Ambient temperature Thermal data
V
1_ 2_ 3_ 4_ 5_ 6_ 7_ 8_ 9_
48
60
rpm mNm mNm rpm rpm mNm A A
3038 2096 1820 15.3 13.3 3150 4000 5750
3022 2441 2120 14.0 12.2 3195 3195 7084
10_ 11_ 12_ 13_ 14_ 15_ 16_ 17_ 18_
46
46
A V
1050 1050 12…60 12…60 0.487 0.437
gcm²
ms
Operating Range n [rpm] 48-V-system
K/W K/W
1.41 0.642 9.83 1260 -30…+85
650 W
s s
4000 3500 3000 2500 2000 1500 1000 500 0
°C
Mechanical data Axial play Direction of force Radial play Preload
mm
19_
0.22 28 Pull
N
22 270 300 [15] preloaded 2500 60 [3000] IP65
20_ 21_ 22_ 23_
M [mNm]
0 1000 2000 3000 4000 5000
Max. axial load (dynamic) Max. force for press fits (static) Max. radial load [mm from flange]
N N N
n [rpm] 60-V-system
650 W
4000 3500 3000 2500 2000 1500 1000 500 0
Other specifications Weight of the drive Typical noise level [rpm]
g
24_ 25_
dBA
Continuous operation Continuous operation with reduced thermal resistance R th2 50% Short term operation
Protection class without shaft Sensor ENC single-turn absolute encoder: resolution, bits EMT multi-turn absolute encoder: resolution, bits Multi-turn: max. no. of turns Supply
M [mNm]
0 1000 2000 3000 4000 5000
12
Gear 412_GPX 70 A/UP 413_GPX 70 LN Modular System
Details on catalog page 42
Motor Control integrated
Stages [opt.]
Sensor integrated ENC integrated EMT Accessories 591_Brake AB 60 S
14 65 536
1–2 1–2
463_GB 12 464_GB 9 465_GB 65
1 1 2
M23, male, 6 poles, N-coded M12, male, 12 poles, A-coded M8, male, 5 poles, B-coded M8, female, 5 poles, B-coded M8, female, 4 poles, A-coded M8, female, 4 poles, A-coded
I/O‘s
CANopen Input CANopen Output EtherCAT Input EtherCAT Output
Compatible cables available online in the configurator.
Configuration Configuration
Flange front: A-Flange / C-Flange Interface with Positioning / Speed Controller: CANopen / EtherCAT Interface with Speed Controller: I/O Angle Power Connector: 0° / 90° Shaft: Standard with feather key/small diameter without feather key
maxon compact drive 365
© 2024 maxon. All rights reserved. July edition. Subject to change.
Made with FlippingBook Publishing Software