Caractéristiques techniques / Teknische eigenschaften TECHNICAL CHARACTERISTICS
*
Requisiti richiesti Requirements Conditions requisés Geforderte eigenschaften
Norma Norms Normes Normen
Caratteristiche tecniche Technical characteristics Caracteristiques techniques Teknische eigenschaften
Valore medio Supergres Average rating Valeur moyenne Durchschnittswert
7 cm ͌ Ð N < 15 cm
N ͍15 cm
RIVESTIMENTO IN PASTA BIANCA - WHITE BODY WALL TILES REVÊTEMENTS EN PÂTE BLANCHE - WEIßSCHERBIGER WANDFLIESEN
Spessore Thickness Epaisseur Stärke
Conforme According to Conforme Gemäss
ISO 10545-2
± 0,5 mm
± 10 %
± 0,5 mm
Norma di riferimento: EN 14411 (ISO 13006) Allegato L Piastrelle di ceramica pressate a secco (E V > 10 %) Reference standard: EN 14411 (ISO 13006) Appendix L Dry pressed ceramic tiles ( E V > 10 %) Norme retenue: EN 14411 (ISO 13006) Annexe L Carreaux céramiques pressés à sec (E V > 10 %) Besugznorm: EN 14411 (ISO 13006) Anlage L Trockengepresste keramische Fliesen und Platten (E V > 10 %)
Conforme According to Conforme Gemäss
Assorbimento % d’acqua Water absorption Absorption d’eau Wasseraufnahme
E V > 10%
ISO 10545-3
Gruppo B III GL
Determinazione della resistenza a flessione e della forza di rottura Flexion and break resistance Résistance à la flexion et à la force de ropture Biegefestigkeit und Bruchlast
Conforme According to Conforme Gemäss
S ͍600 N R ͍15 N/mm 2
ISO 10545-4 Spessore 7,5 mm
*
Requisiti richiesti Requirements Conditions requisés Geforderte eigenschaften
Norma Norms Normes Normen
Caratteristiche tecniche Technical characteristics Caracteristiques techniques Teknische eigenschaften
Valore medio Supergres Average rating Valeur moyenne Durchschnittswert
Conforme According to Conforme Gemäss
Richiesta Required Requise Enforderlich
Determinazione della resistenza al cavillo Crazing resistance Résistance aux craquelures Haarriß-Beständigkeit
ISO 10545-11
N ͍15 cm
7 cm ͌ Ð N < 15 cm
Lunghezza e larghezza Lenght and width Longuer et largeur Länge und Breite
Conforme According to Conforme Gemäss
Conforme According to Conforme Gemäss
Classe GB minimo Class GB min Categorie GB min Klasse GB min
Determinazione della resistenza chimica (GL) Chemical resistance (GL) Résistance chimique (GL) Chemikalienbeständigkeit (GL)
± 0,4 mm
± 0,3 %
± 1,0 mm
ISO 10545-13
Conforme According to Conforme Gemäss
Rettilineità degli spigoli Straightness of sides Equerrage des angles Kantengeradheit
Conforme According to Conforme Gemäss
Classe 3 minimo Class 3 min Categorie 3 min Klasse 3 min ǯ
Determinazione della resistenza alle macchie Resistance to staining Résistance aux taches Beständigkeit gegen Fleckenbil
± 0,4 mm
± 0,3 %
± 0,8 mm
ISO 10545-14
ISO 10545-2
Ortogonalità Rectangularity Orthogonalité Rechtwinkligkeit **
Conforme According to Conforme Gemäss
Conforme According to Conforme Gemäss
Classe A1 o A1 fl Class A1 o A1 fl Class A1 ou A1 fl Klasse A1 oder A1 fl
Reazione al fuoco Reaction to fire Réaction au feu Brendverhalten
± 0,4 mm
± 0,3 %
± 1,5 mm
-
Planarità Flatness Planéité Planität
Conforme According to Conforme Gemäss
± 0,6 mm
± 0,4 %
± 1,8 mm
Lunghezza e larghezza Lenght and width Longuer et largeur Länge und Breite
Conforme According to Conforme Gemäss
*
Valori riferiti ai fondi. Le caratteristiche tecniche fanno riferimento al formato nominale delle piastrelle espresso in mm. These values refer to the bottoms. The technical characteristics refer to the nominal size of tiles expressed in mm Valeurs se référant aux fonds. Les caractéristiques techniques se réfèrent au format nominal des carreaux exprimé en mm. Werte bezogen auf Grundliesen. Die Angaben beziehen sich auf die Nenngröße der Fliesen in mm. Se non indicato diversamente, i valori delle prove tecniche si riferiscono alla superficie naturale. Unless otherwise indicated, the values of technical tests refer to the natural surface finish. Sauf indication contraire, les valeurs des tests techniques se rapportent à la surface naturelle. Wenn nicht anders angegeben beziehen sich die Werte der technischen Tests auf die natürliche Oberfläche. Per piastrelle rettangolari che abbiano il lato maggiore L 60 cm, e rapporto tra i lati 3, la misurazione dell’ortogonalità deve venire condotta solo sul lato corto. For rectangular tiles with longest side L ɵ 60 cm and a ratio length/width L/W ɵÁ 3, the measurement of orthogonality should only be carried out on short edges. Pour les carreaux rectangulaires qui ont le côté le plus long L ɵ 60 cm, et le rapport entre les côtés ɵÁ 3, la mesure de l'orthogonalité se fait seulement sur le côté le plus court. Bei rechteckigen Fliesen, mit der längsten Seite L ɵ 60 cm und einem Seitenverhältnis von ɵÁ 3 darf die Messung der Rechteckigkeit nur an der kurzen Seite durchgeführt werden.
± 0,9 mm
± 0,6 %
± 2,0 mm
Rettilineità degli spigoli Straightness of sides Equerrage des angles Kantengeradheit
Conforme According to Conforme Gemäss
± 0,8 mm
± 0,5 %
± 1,5 mm
ISO 10545-2
Ortogonalità Rectangularity Orthogonalité Rechtwinkligkeit **
Conforme According to Conforme Gemäss
**
± 0,8 mm
± 0,5 %
± 2,0 mm
Planarità Flatness Planéité Planität
Conforme According to Conforme Gemäss
± 0,8 mm
± 0,5 %
± 2,0 mm
310
311
Made with FlippingBook Annual report maker