Tank Cleaning Heads
IBC Cleaning
Hydraulic (Water) Driven Tank Cleaner Mi63
Ideal for IBC cleaning (Intermediate Bulk Container) Flow: 15-50 l/min., 90°C Pressure: 435 Psi to 2000 Psi Barrell Diam. 45mm or 65mm Inlet: 3/4” Bsp F MaxFlow: 2320 Psi, Temp to 90
Part #
Shaft Length Flow max.
Min. Inlet
Max. Nozzles
List
145 25.4603.24
363mm
22 l/min.
45mm
4 x M4
$4,781 C
145 25.4600.04
915mm
Unjetted
45mm
4 x M4
$4,781 C
145 25.4600.24
915mm
22 l/min.
45mm
4 x M4
$4,781 C
145 25.4606.24A
650mm
22l/100B
45mm
$4,999 B
145 25.4600.00
915mm
Unjetted
65mm
4 X 1/8 Npt
$3,656 C
145 25.4603.20
363mm*
22 l/min.
65mm
4 X 1/8 Npt
$4,999 C
145 25.4600.30
915mm
30 l/min.
65mm
4 X 1/8 Npt
$5,056 C
Stainless Versions 145 25.3650.40
650mm
45 l/min.
62mm
4 X 1/8 Npt
$4,884 C
145 25.3650.50
650mm
45 l/min.
62mm
4 X 1/8 Npt
$4,884 D
ATEX Versions 145 25.4902.25
915mm
Unjetted
65mm
4 X 1/8 Npt
$poa C
145 25.4902.29
915mm
Unjetted
45mm
4 X M4t
$poa C
Repair Kit 145 25.4608.24
Spares Kit - Seals
$238 C
145 25.4630.24
Spares Kit - Gears etc
$508 C
145 80.0005.52
Buffer, M10 Sst
$353 C
145 80.0014.51
Nozzle hold. pinion, z57,4x1/8”Npt F
$336 C
145 80.0009.85
Bushing, opn 15x19x14.8mm, 8mm PTFE
$12 C
145 80.0027.23
Pinion 34 Sst+Bushing opn 15mm
$296 C
145 80.0232.51
Geared shaft
$618 C
145 80.0205.00
Planetary Gear Holder
$319 C
145 80.0203.52
Turbine Set
$767 C
145 80.0016.51
Nozzle Holder Pinnion
$400 C
145 80.0134.52
Nozzle Holder Pinnion - Straight
$778 C
145 28.0518.23
Feeler + cable
$88 C
Nozzles & Nozzle Change Mi63 supplied standard with 2 nozzles and the other 2 ports plugged. 4 Ports used for higher flow applications Head with M4 Nozzles Nozzle Sizes (025)145 25.1091.51 $7D, (020)145 25.1190.51 $7D, (035)145 25.1093.51 $9 D, (043)145 25.1194.51 $9C Head with 1/8” Nozzles (045) 145 16.1363.45 1/8” Npt + Guide Vane 00.045 Must also change injector (x3): (2mm) 145 80.0221.51 $29C, (3mm) 145 80.0222.51 $39C, (4mm) 145 80.0223.51 $35C, (5mm) 145 80.0224.51 $32C Cycle Time: Cycle time of head is effected by flow, not pressure. When changing nozzles, cycle time will not change if you keep the same flow rate * 363mm shaft Can convert 915mm to 363mm shaft with following: Outer shaft 363MM 145 80.0066.56 $214 C / Inner shaft 145 80.0065.56 $68 C
◄ Water Hydraulic Gear motor Water Hydraulic Gear Motor
145 80.0003.56 145 80.0011.56
894mm $130 C 829mm $ 91 C
894mm 829mm
$133 D $93 C
Nozzle doing the cleaning ► Nozzle doing the cleaning
Selection note: M25E series has suction recovery Mi63 has no suction as the liquid drains from the tap below
Service Advice (2017 July) : Daily - Rinse daily 100 Hours usage - Service check, especially if cleansing products are used 400 Hours usage - Replace all internals ie seals & gears
593
Indicative prices only, excludes GST & Freight
Made with FlippingBook - Online magazine maker