Pressure Cleaners
The axial pump is similar to the wobble, but features a larger oil reservoir and larger bearings to allow the pump to run cooler to extend life. The axial pump also has larger cylinders, which enable it to generate higher PSI and GPM ratings than a standard wobble. Although performance is improved, the axial still is effected by piston spring resistance that translates in to lower performance and efficiency versus a camshaft pump. The camshaft pump offers many benefits over the “wobble” and “axial-style” pumps. Due to the use of connecting rods and positive action pistons (like a car engine), a camshaft pump is much more efficient (85% efficient) than an axial-style pump, which must overcome spring tension and friction to generate pressure. Another benefit of this design is that a camshaft pump generates much less heat and therefore runs cooler than an axial-style pump, and heat is the number one cause of failure in a high-pressure pump. For this reason, a camshaft pump can easily provide 1,000 hours or more of operation before needing any maintenance, whereas an wobble or axial-style pump typically has a life span of 200-600 hours, after which the pump often can not be repaired economically. Also, when a camshaft pump does require maintenance, the easily accessible pump head, replaceable cartridge-type valves, and ceramic piston sleeves makes repair quick and easy. Tips on Proper Spraying Techniques Operator error is the leading cause of user dissatisfaction when it comes to power tools, and pressure cleaners are no exception. There are three ways to control the cleaning power of your pressure cleaner: 1) A djust the throttle on the gas engine to control speed. Some units also may have a regulator knob on the pump that can adjust the pressure (if so equipped). 2) A djust the spray pattern at the nozzle. Choose the widest pattern possible for spraying when starting the job and adjust the pattern to a narrower angle until you find a suitable pattern. Remember to temper power with coverage ability when spraying. 3) F inally, the easiest way to regulate the cleaning power of your pressure cleaner is distance from the surface you are cleaning. Begin several feet from the surface and slowly move closer, adjusting the spray pattern as necessary. Hold the nozzle a uniform distance from the surface to ensure that no part of surface is cleaner that another. Nozzles and Tips Many units feature nozzles with a variable spray pattern (0-40 degree angle), while others have individual quick connect tips with a pre-set spray angle. The size of the nozzle influences both pressure and flow rate. The spray angle of the nozzle also plays an important role. The wider the spray angle, the lower its ability to cut through dirt. A wide pattern (40 degrees) will distribute the impact of water over a large area, resulting in excellent cleaning action with reduced surface damage risk. The optimum angle for spraying water against a cleaning surface is 45 degrees. A fan pattern (15-25 degrees) balances stripping power and washing. It is useful for moving dirt and is the best choice for cleaning large flat surfaces such as patios and driveways. At 0 degrees, a narrow stream pattern delivers a high impact force resulting in maximum deep cleaning in concentrated area. The narrow stream is best suited for concrete masonry or brick and can be used to remove paint or tough dirt. Detergents Detergents can dramatically reduce cleaning time and assist in the removal of tough stains, grease, bugs and dirt. Apply them with a low-pressure spray and allowing them to soak into the surface to break down the dirt and grime. Many detergents are customized for pressure cleaner use on specific cleaning tasks. Only use detergents intended for pressure cleaners. Thicker detergents such as dish soap will clog the chemical injection system and potentially damage your pressure cleaner. Be aware the EPA prohibits point source discharge of pollutants without a permit. While this may not be an issue on the job site when using only water, if you are cleaning equipment with detergents in shop or storage yard on a continuing basis, you should check on obtaining a permit and/or installing a waste water recover system.
Importantly, if using detergents, flush the water pump with clean water after each use.
Maintenance:
Engine maintenance is the same as on other petrol powered equipment. Check your oil level regularly, some models have automatic low oil shutdown switches to protect the engines. On gas models slowly pull the start rope five times to purge water from the pump.
777
Indicative prices only, excludes GST & Freight
Made with FlippingBook - Online magazine maker