Filtered Valve Cover Breathers Hooded and non-hooded breathers are avail- able in two styles, clamp-on or push-in. The steel housings on all breathers are chrome-plated. Elements must be oiled before use and are easily cleaned with soap and water. Elements must be dry before re-oiling. Sold individually. Part No. Description MOR68811
Fuel Pump Block-Off Plates Block the fuel pump boss when mechanical fuel pump is not used. Available in anodized aluminum, chrome-plated steel, and L>V>`âi`LiÌ>ÕÕwà ið
Black Anodized Aluminum
Chrome Plated Steel
Black Anodized Billet Aluminum
Description
MOR68813
Small Block Chevy
MOR65391 MOR65393 MOR65395
Hooded Clamp-On Type, Fits 1-3/8" Tube Hooded Clamp-On Type, Fits 1-1/2" Tube
Deck Plug Kit MOR37800 Install 3/4" NPT plugs in block to greatly reduce upper cylinder wall distortion in
MOR68812 MOR68813 MOR68815 MOR68816 MOR68817
Hooded Push-In Type, for Covers w/Punched Hole Non-Hooded Clamp-On Type, Fits 1-3/8" Tube Non-Hooded Clamp-On Type, Fits 1-1/2" Tube
Ã>LV>`äc6È iÛÞðiÃÕÃÌLiÌ>««i`LivÀi the plugs are screwed in, and block machining is necessary >vÌiÀÃÌ>>Ì°*Õ}Ã>ÃÀiÃÌÀVÌÜ>ÌiÀyÜÌÌ iVÞ`iÀ heads by reducing water passage holes. Six per package. Quick Fastener Washers MOR71610 *ÀÌiVÌÞÕÀV>À½Ãwà vÀÃVÀ>ÌV ià and squeaks. Fits all quick fasteners. Racing Radiator Caps High-pressure radiator caps are engineered for standard radiator necks and utilize stainless steel springs and solid brass spring retainers. Part No. Description MOR63320 19-21 PSI MOR63324 23-25 PSI MOR63328 27-29 PSI Engine Cleaning Brushes MOR61820 Quality engine builders know `iÃ}i`vÀ>ëiVwV«ÕÀ«Ãi°/ iÀi>ÀiÌÜi>V vÌ i gallery brushes, since they get the most wear. They can also be used on crankshaft oil holes, cylinder heads, etc. Nylon bristles clean as well as wire, but will not scratch. Set of 12. Stud Mount Valve Spring Compressors 6>ÛiëÀ}V >}}Ã}Ài>ÌÞëwi` how important it is to have a clean block, especially in the hard-to- get-at areas of the oiling system. Each of these nylon brushes was
Non-Hooded Push-In, for Covers With Punched Hole Note: The hooded filtered breathers should be installed with the hood facing the fan so that no grit can be blown into the element.
Valve Cover Stud Kits Studs ease valve cover instal- lation or removal and prevent
loosening caused by vibra- tions. “Bullet Nose” studs make it easier to start threads on mounting nuts. Sold in sets of eight with 1/4"-20 studs, nylon insert lock nuts, and washers. Part No. Description MOR68820 Valve Cover Stud Kit, 1/4"-20 x 1-3/4" MOR68830 “Bullet Nose” Valve Cover Stud Kit, 1/4"-20 x 1-1/2" Small Block Chevy Valve Cover
Hold-Down Tabs MOR68510 Chrome-plated steel tabs spread the fastener load over a larger area of the Û>ÛiVÛiÀy>}iÌi>Ìi`ÃÌÀÌ and leakage. Set of four 5" hold down tabs with 5/16" holes service one cover. Perm-Align Valve Cover Gaskets
Durable gaskets won’t leak, blow out, or get sucked in. Gas- kets are 3/16" thick and made of 40 durometer rubber, vulca- nized to a rigid steel frame to provide years of dependable service. Two per package.
ÜÌ Ì ÃÃÌÕ`ÕÌÌÜ V ÜwÌ both 3/8" and 7/16" rocker studs. The strong 12" handle provides ample leverage to overcome the resistance of extremely high pressure valve springs. Part No.
Part No.
Description SB Chevy
MOR93020 MOR93021
MOR93021
SB Chevy With 12°, 13.5°/15°/16°/18°, Brodix /Dart/Edelbrock/All-Pro Heads
Description
MOR62370
Stud Mount Valve Spring Compressor
In-Line Fuel Filters Anodized aluminum fuel wÌiÀÃÕÃiVi>>Li]{äVÀÃÌ>iÃÃÃÌiiiiiÌÃÌ remove dirt and debris from the fuel system. Part No. Description MOR65230 Fuel Filter, -8AN Fittings, 6-1/2" Long MOR65231 Fuel Filter, Accepts 3/8" NPT Fittings, 5-1/8" Long MOR97062 Replacement 40 Micron Filter Element
Contains All Parts Necessary To Convert MOR62370 To Use with Jesel Rocker Shaft Systems
MOR62372
MOR65230
294 2019 OPEN WHEEL PARTS AND ACCESSORIES
Made with FlippingBook flipbook maker