Range overview
Flow-optimised press connector system made of copper (99.9 % Cu-DHP), gunmetal or silicon bronze for copper pipes. Press connectors for protecting the sealing element equipped with cylindrical pipe guide. Press connectors from d64.0 with stainless steel cutting ring to ensure the mechanical strength of the connection. The pressing force is located before and behind the sealing element seat. Suitable for concealed and pre-wall installations of riser pipes and floor installations. Marking Manufacturer, pipe dimension, batch, approval markings (DVGW), yellow dot on press end, yellow rectangle with inscription »Gas MOP 5 / GT1«, detachable orange label as press indicator from d64.0 Press connector with SC-Contur Inadvertently unpressed connections are noticed immediately during a leakage test. Viega guarantees the detection of unpressed connections in the following pressure ranges with compressed air or inert gases: Min. air pressure: 22 hPa / 2.2 kPa / 22 mbar / 0.3 PSI Max. air pressure: 0.3 MPa / 300kPa / 3 bar / 43.5 PSI Sealing elements HNBR (hydrogenated acrylonitrile butadiene rubber), yellow, pre-assembled Dimensions d12–64.0, size availability in accordance with the national regulations Tools The functional safety of Viega press connector systems depends primarily on the faultless condition of the press tools used. For the installation of press connections, Viega recommends the use of Viega press tools. Viega press tools have to be regularly maintained by authorised service partners.
Operating conditions gas and liquid gas installations Operating temperature -20 °C to +70 °C (-4 °F to +158 °F) Operating pressure max. 0.5 MPa / 5 bar / 72.5 PSI Operating pressure at HTB requirements 650°C (1202 °F)/30 minutes max. 0.1 MPa (1 bar; 14.5 PSI) Operating conditions heating oil and diesel fuel installation Operating temperature max. 40 °C / 104 °F Operating pressure -0.05 to +0.5 MPa (-0.5 to +5 bar / -7.25 to +72.5 PSI)
Press connector material Copper: 99.9 % Cu-DHP Gunmetal: CC499K Silicon bronze: CC246E / CuSi4Zn9MnP
Subject to change without prior notice! Latest Z- and installation dimensions as well as further technical information can be found on the Viega website and have to be checked before purchase, planning, construction work and use. Our products are continuously optimised. This product description contains important information on choice of product and system, mounting, commissioning as well as intended use and, if required, on maintenance measures. This information on products, their features and application techniques is based on currently valid standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW). Some passages in the text may refer to technical regulations in Europe/Germany. These should be considered as recommen- dations for other countries where no corresponding national requirements exist. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this product description: The information herein is not binding for other countries and regions and should be understood as recommendation.
Areas of application Natural gas/liquid gas Heating oil/diesel fuel (d12–54)
Note Use of the system for areas of application and media other than those described must be agreed in consultation with Viega! Detailed information about applications, restrictions and national standards and directives can be found in the product information, either printed or on the Viega website. Note – Standards and approvals Press connectors tested in accordance with DVGW Worksheet W 534 with DVGW test mark. Approval for d12–64.0 in accordance with DVGW-registration no. DG 4550AU0070. Press connectors suitable for copper pipes in accordance with DIN EN 1057 and DVGW Worksheet GW 392. Gases in accordance with DVGW G 260 in gas installations in accordance with DVGW-TRGI 2018 (DVGW Worksheet G 600) / DVFG-TRF 2021. Liquid gases in the gas phase for domestic and commercial applications, tested in accordance with DVGW Worksheet G 5614. Piping for heating oil in accordance with DIN 51603 and piping for diesel fuel as suction and pressure line in accordance with DIN EN 590 in consideration of the General Building Approval Z-38.4‑71.
36
Made with FlippingBook - Online catalogs