Range overview
Flow-optimised press connector system made of non-alloy steel 1.0308 with an externally galvanised zinc-nickel coating for black, galvanised, industrially painted and powder-coated steel pipes. Press connectors with stainless steel cutting ring to ensure the mechanical strength of the connection. Suitable for concealed and pre-wall installations of riser pipes and floor installations. Marking Manufacturer, pipe dimension, batch, white dot on press end, black rectangle with symbol »Not approved for potable water installations«, detachable white label as press indicator
Note Use of the system for areas of application and media other than those described must be agreed in consultation with Viega! Detailed information about applications, restrictions and national standards and directives can be found in the product information, either printed or on the Viega website. Note – Standards and approvals Suitable for steel pipes in accordance with EN 10255, EN 10220 / EN 10216‑1, EN 10220 / EN 10217‑1. For use in heating systems, observe VDI Regulation 2035 and DIN EN 12828. Not suitable for fuel gases in accordance with DVGW Worksheet G 260 and potable water installations, as well as other open systems. Operating conditions Operating temperature -5 °C to +140 °C (23 °F to 284 °F) Operating pressure max. 1.6 MPa (PN16) / 1600 kPa / 16 bar / 232 PSI
Press connector with SC-Contur Inadvertently unpressed connections are noticed immediately during a leakage test. Viega guarantees the detection of unpressed connections in the following pressure ranges with water, compressed air or inert gases: Min. water pressure: 0.1 MPa / 100kPa / 1 bar / 14.5 PSI Max. water pressure: 0.65 MPa / 650kPa / 6.5 bar / 94.3 PSI Min. air pressure: 22 hPa / 2.2 kPa / 22 mbar / 0.3 PSI Max. air pressure: 0.3 MPa / 300kPa / 3 bar / 43.5 PSI
Press connector material Steel 1.0308
Protection against external corrosion Thanks to a zinc-nickel coating the press connectors are optimally protected against corrosion – e.g. when condensation forms in cooling systems. The pipe being used should be protected with suitable corrosion prevention – observe manufacturer’s information. Pipes and pipe connectors should be insulated in the same way in accordance with the general rules of engineering. Subject to change without prior notice! Latest Z- and installation dimensions as well as further technical information can be found on the Viega website and have to be checked before purchase, planning, construction work and use. Our products are continuously optimised. This product description contains important information on choice of product and system, mounting, commissioning as well as intended use and, if required, on maintenance measures. This information on products, their features and application techniques is based on currently valid standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW). Some passages in the text may refer to technical regulations in Europe/Germany. These should be considered as recommen- dations for other countries where no corresponding national requirements exist. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this product description: The information herein is not binding for other countries and regions and should be understood as recommendation.
Sealing elements FKM (fluorocarbon rubber), matt black, pre-assembled
Notice The sealing materials of the press connector system are subject to thermal ageing, which depends on the media temperature and the operating time. In the case of special operating conditions, e.g. industrial heat recovery systems, it is necessary to compare the specifications of the appliance manufacturer with the specifications of the press connector system. Before using the press connector system beyond the areas of application described or if in doubt about the correct selection of material, please contact Viega. Dimensions D⅜–4, size availability in accordance with the national regulations Tools The functional safety of Viega press connector systems depends primarily on the faultless condition of the press tools used. The Pressgun Press Booster is required for manufacturing Megapress S XL press connections. Viega press tools have to be regularly maintained by authorised service partners. Areas of application Industrial and plant engineering Local and district heat systems as per AGFW FW 524 (after entry into the building, ≤ DN50) Closed cooling and heating systems Compressed air systems Fire extinguishing and sprinkler systems (the required minimum
and maximum wall thickness have to be observed) Systems for technical gases (request required)
68
Made with FlippingBook - Online catalogs