LIS-58100
ATD-8701
49 D
LIS-41500
ATD-8629
R
ATD-8705
MTI-18650
ATD-3046
CCT-4017
XL C-FRAME BALL JOINT PRESS
PULLERS, SEPARATORS, HUB TOOLS
Includes: • (1) C-clamp • (1) each long and short drive screw • (1) removal adapter • (1) install adapter
ATD-8641
ATD-3058
ATD-3046
$36.29
Pitman Arm Puller
Heavy-duty center screw and heat treated yoke drop forged from high grade alloy steel for a safe and steady pull. Heavy-duty yoke eliminates spreading and breakage. Spread the open end of a pitman arm for easy removal on Class 3-8 vehi- cles. Easily install bearing cups of SPL series u-joints into full round yokes.
• Extra-large ball joint press for maximum clearance • Will work with ATD and other ball joint removal and installation adapters • Kit includes long and short drive screws for shorter working length • 9.1” throat, 11.9” length
MTI-18650
$66.79
Heavy-Duty Pitman Arm Spreader
ATD-3053
ATD-8700 ATD-8701 LIS-41500
$19.09 $19.89 $59.19
Ball Joint Separator
15/16” Opening x 12” Long
Tie Rod Separator
5/8” Opening x 16” Long
Pickle Fork Kit
Kit consists of (3) forks and (2) handles; (1) for manual hammering and (1) for use with an air hammer (.401” shank). Heavy-duty forgings, handles are heat-treated alloy steel. Made of heavy, drop-forged chrome vanadium steel. Includes: (3) Forks: 11/16”, 15/16” and 1-1/8”, (1) Handle for use with air hammer and (1) Handle for use with manual hammer The long socket slips over tie rod end and crows foot engages on socket for easy removal and installation of tie rods with inaccessible wrench flats. Includes: (12) Crowsfeet: 1-3/16”, 1-1/4”, 1-3/8”, 1-1/2”, 1-5/16”, 1-7/16”, 29mm, 32.5mm, 33.6mm, 38.4mm, 40mm and 42mm to fit many cars, trucks and SUVs. Safely removes frozen hub assemblies instantly. Universal mount fits all axle bolted hubs (5, 6 and 8 lug hubs). Mounts to 2 studs using supplied flange nuts. Use with 5 lbs. hammer to knock frozen hubs out of axles. 3/4” steel backing plate and reinforced striking plate for long life. Heavy-duty steel tool removes Ford and Dodge 4WD Pickup wheel hubs without damage to the wheel bearings. Fits on most 5, 6 and 8 lug hub assemblies found on cars and trucks. Bolt the 1/2” thick driving plate to the hub using the hardened washers and existing lug nuts. Insert the hardened thread forcing screw to push against a solid surface to loosen the hub assembly Tool will remove wheel hubs mounted on tapered axles and press fit rear brake drums. Made of alloy steel and drop forged, this heavy-duty tool has a center screw 1”-14 x 9” with a 1-1/8” hex head. For use on domestic and import cars and light trucks with 4-, 5-, or 6-bolt stud design, and all non-C lock GM axles. Range is 3-3/4” to 4-1/2”. Use with ATD-3045, heavy-duty puller set. Slide hammer pulls many flange-type rear axles and axle bearings. Includes: (3) bearing adapters, (1) 5/8”-18T x 22-1/2” slide screw, (1) 5/8” lock nut, (1) axle yoke, (1) 3.75 lbs. slide hammer, (1) bearing hook. Separates half-shafts from transaxle. Shim tool is included to fill gaps on some applications. Better and safer than hammer and bar. Both are 14” / 36cm long with 2” / 51mm opening. Machine forged for strength and durability.
• Live center forcing screw plug • Heavy-duty steel and cast metal construction • Includes all receiver tubes and adapters needed to work on press-fit upper and lower ball joints on most 2WD and 4WD pickups, vans and SUVs thru 2006 MASTER BALL JOINT SERVICE SET LIS-41630 ....................$42.89 CASTER CAMBER KIT FOR GM, 21mm & 24mm The 14-1/2” 21mm/24mm wrench can be used to move hard-to-reach and often rusty OEM cams on 1999 and newer GM 1/2 and 3/4 Ton vehicles with coil spring front suspensions. The kit includes a cam adjusting holding tool to adjust the upper control arm cams found on Chevrolet and GMC vehicles. ATD-8695 ..................... $98.39
ATD-8705
$51.49
5 Pc. Ball Joint and Tie Rod Separator Set
LIS-58100
$201.49
12 Pc. Inner Tie Rod Tool Set
ATD-3057
ATD-8629
$159.95
Wheel Hub Removal Tool
LIS-40100
ATD-8641
$50.39
Hub Tool for Ford and Dodge 4WD Pickups
ATD-5147
LIS-40100
$136.99
Hub Remover
ATD-3058
$147.09
Hub Puller
DELUXE BALL JOINT SERVICE SET ATD-8699 ...................... $311.49
AST-7848
ATD-3057
$45.39
Flange Type Axle & Front Wheel Hub Puller
ATD-3053
$157.19
Rear Axle Puller Set
ATD-5464
CCT-4017
$65.69
Axle Popper Kit 2 Pc.
ATD-8696 ...................... $152.39
BRAKE TOOL SETS
Includes: • C-frame press & (3) receiver tubes: 2-3/4” x 3”, 2-1/4” x 2-1/2” and 1-3/4” x 2” • Adapters for ‘67-current 1/2 and 3/4 Ton 4WD vehicles having the Dana 44 front axle (found on Ford, GM, Dodge, IHC & Jeep vehicles)
ATD-5147
$47.39
7 Pc. Drum Brake Tool Set
Services most domestic and import drum brakes. Includes tools for removing and installing springs, bleeding system and adjusting brakes. Includes: (2) brake adjustment spoons, (1) brake retaining spring tool, (1) spring compressor and removal tool, (1) brake spring pliers and installer.
ATD-5478
AST-7848
$41.19
8 Pc. Pro Brake Tool Set
ADD-ON SERVICE SET FOR ATD-8696
FLARING TOOLS
$112.49
ATD-5478
Master Flaring and Tubing Tool Set
Incudes: Mini tubing cutter, metric flaring tool bar assembly, universal flaring tool yoke, SAE flaring tool bar assembly, adapter wrench, tubing bender with (2) adapter wheels, (5) SAE flaring tool adapters: 3/16”, 1/4”, 5/16”, 3/8” and 1/2”, (4) ISO bubble flaring tool adapters: 4.75mm, 6mm, 8mm and 10mm. Forged steel yoke, flaring bar and all the adapters needed for ISO bubble flaring. Designed for crack-free bubble flares on soft steel tubing used in automotive brake systems. Includes: 4.75mm adapter (PRT5464-01), 6mm adapter (PRT5464-02), 8mm adapter (PRT5464-03), 10mm adapter (PRT5464-04). Adapters are also available individually. Works on copper, aluminum, soft steel, brake line and brass tubing to 45˚. Includes: 3/16” adapter (PRT5463-01), 1/4” adapter (PRT5463-02), 5/16” adapter (PRT5463-03), 3/8” adapter (PRT5463-04), 1/2” adapter (PRT5463- 05) and storage case. Adapters are also available individually. This Kit Fabricates: Push Connect Flares: 1/4, 5/16 and 3/8”; GM Fuel Line Flares: 5/16 and 3/8”; Metric Bubble Flares: 4.75, 6, 8 and 10mm; Flare/ Double Flares: 3/16, 1/4, 5/16, 3/8 and 1/2”. FREE Mini Tube Cutter for 1/8” to 5/8” OD tubing.
• Includes all the receiver tubes and adapters needed to work on most GM, Ford and Dodge 2WD and 4WD pickups, vans SUVs thru current ATD-8697 ...................... $170.39 WHEEL BEARING HUB PULLER REMOVAL KITS
ATD-5463
ATD-5464
$53.99
Bubble (ISO) Flaring Tool Kit
$47.29
ATD-5463
Double Flaring Tool Kit
Engineered Performance
Pull the most stubborn wheel bearing hubs, without having to remove the control arm or use a hammer. This wheel bearing hub removal tool is for select ford and Subaru models. Also available in a Ford/Subaru combination kit.
MST-72475
MST-72475
$419.95
Universal Hydraulic Flaring Tool Set
MIL-TOM450PROP .............$1,109.95
Made with FlippingBook flipbook maker