FLUID POWER Weatherhead Hydraulics 6
COLL-O-CRIMP COUPLINGS — 338 P-SERIES
Assemble Instructions: 1. Push collar onto hose until bottomed 2. Push insert into hose until step on insert (or hex) is flush with collar
• Typical Application: Air brake hose lines • Compatible Hose: J97.523.1216 prefix ( ECO38 ) • Pressure: Determined by hose burst pressure • Material: CA360 Brass • Advantages: A permanent hose end saves time and is easy to assemble. Brass material offers excellent resistance against corrosion. • Assemble With: T-400-1 T-410-1 T-420-1 T-440-1, T-460- T-462- T-440- T-465- T-480-
Note: Swivel fittings require the use of a mandrel or an assembled adapter to push on the insert for assembly. Adapter can be removed after fitting assembly. Light lubricant may be required to assemble fitting into hose. 3. Check for bottoming by checking collar movement along insert. Hose is bottomed when collar cannot slide along insert 4. Depending on Coll-O-Crimp system, follow recommended operating procedures
MALE PIPE RIGID Hose I.D. Pipe Size
Hose Cut-Off Factor
Hole Dia.
Hex E
Thread Size
A A
Danfoss No.
Part No.
A
J97.550.64 J97.550.66 J97.550.86 J97.550.88
3/8 3/8 1/2 1/2
1/4 3/8 3/8 1/2
1/4-18 3/8-18 3/8-18 1/2-14
1.71 1.72 1.73 1.94
.75 .81 .81
.28 .28 .38 .38
9/16
33806P-104 33806P-106 33808P-106 33808P-108
11/16 11/16
E
1.00
7/8
MALE PIPE SWIVEL Hose I.D. Pipe Size
A A
Hose Cut-Off Factor
Hole Dia.
Hex E
Thread Size
Danfoss No.
Part No.
A
J97.551.66
3/8
3/8
3/8-18
2.18
.81
.28
9/16
33806P-J06
E
AIR BRAKE SWIVEL Hose I.D. ABS Size
A A
Hose Cut-Off Factor
Thread Size
Danfoss No.
Part No.
A
Hole Dia. Hex F
J97.554.66 J97.554.86
3/8 1/2
3/8 3/8
3/4-20 3/4-20
1.38 1.38
1.00 1.00
.28 .28
3/4 3/4
33806P-Y76 33808P-Y76
F F
ADAPTER ABS Size
Pipe Size
Overall Length
ABS Thread Size
Danfoss No.
Part No.
J97.555.66 J97.555.68 J97.555.86 J97.555.88
3/8 3/8 1/2 1/2
3/8 1/2 3/8 1/2
1.18 1.37 1.18 1.37
3/4-20 3/4-20 7/8-20 7/8-20
1390 x 6 x 6 1390 x 6 x 8
1390 x 8
7
1390 x 8 x 8
COLL-O-CRIMP COUPLINGS — E-SERIES
HOSE END SERIES: ‘E’ SERIES
• Typical Application: General Purpose low and medium pressure hydraulics. Use H435 where shock hazard exist
• Material: AISI/SAE 12L14, carbon steel • Plating: Zinc yellow dichromate finish • Advantages: Wide selection of hose and end configurations allowing for a diverse number of applications where hose compatibility is a problem
• Compatible Hose: H009, H209, H243, H265, H275, H285, H435 and H436 • Pressure: Determined by maximum working pressure of hose size
SAE 37° (JIC) FEMALE SWIVEL Hose I.D. Tube Size Thread Size A
A
Hose Cut-Off Factor*
Hex E 7/16 9/16
Hex F
Danfoss No.
Part No.
J97.121.44 J97.121.66
1/4 3/8
1/4 3/8 1/2
7/16-20 5/8-18 3/4-16
1.92 1-1/8 2.06 1-1/8 2.45 1-1/2
9/16
04E-604 06E-606 08E-608
3/4 7/8
1/2 J97.121.88 * To determine the correct length of hose, subtract the cut-off factor for each end fitting from the overall length of the assembly. 3/4
E
F
SAE 37° (JIC) MALE RIGID Hose I.D. Tube Size Thread Size
A
Hose Cut-Off Factor*
Hex E
Danfoss No.
Part No.
A
J97.138.66
3/8
3/8
9/16-18
1.92
1.00
5/8
06E-506
* To determine the correct length of hose, subtract the cut-off factor for each end fitting from the overall length of the assembly.
E
Copyright © 2025
7-6-5
Made with FlippingBook - professional solution for displaying marketing and sales documents online