OTHER ACCESSORIES
High Frequency
Fluke Connect ®
85RF High Frequency Probe Converts a DC voltmeter with an input impedance of 10 megohms into a high frequency (100 kHz to 500 MHz) RF voltmeter • Voltage range: 0 25 V to 3 V AC RMS • Maximum input: 30 V RMS, 200 V DC • AC to DC ratio: 1:1 • Ratio accuracy at 25 MHz and loaded with 10 megohms
PV350 Pressure Vacuum Module Single unit allows digital multimeters to make both pressure and vacuum measurements • Transducer sealed in 316 stainless steel compatible with variety of liquids and gases • Vacuum measurement: to 76 cm Hg • Pressure measurement: to 3447 kPa
ir3000 FC Connector for Fluke Connect ® • Get all the benefits of the Fluke Connect ® app, and be on the same page, even while in different places • Wirelessly share measurements with your team—anywhere, anytime • Connect the Fluke 289/287 Multimeters, Fluke 1550C/1555 Insulation Testers and Fluke 789 ProcessMeter™ with the ir3000 FC
Fiber Optics
IR189USB USB Cable Adapter Included with FVFSC2 and FVF-Basic software • Small adapter to connect the cable to the 189, 287, 289, 1653B or the 1550C is included
PC3000 Wireless PC Adapter • Fluke PC3000 FC Adapter and software • Must be connected to the USB port in order to enable communication between FC modules and software • SW3000 supports up to two PC3000 FC Adapters
FOM Fiber Optic Meter Allows testing and maintenance of fiber optic cables without buying a new meter It plugs directly into any digital multimeter with an mV DC function and a 10 megohm input impedance to quickly and accurately verify fiber optic cable system loss • Wave lengths: 1550, 1300, 850 & nm • Light sources sold separately
SV225 Stray Voltage Adapter Stray voltage can appear in electrical installations, due to the capacity between wires This may result in erroneous readings on high impedance meters The SV225 solves this without compromising safety • On energised wires, the meter will indicate the real voltage • On non-energised circuits the meter will read close to zero (even if there are stray voltages) • Can be used on all meters with standard input spacing • Safety rating: CAT III 1000 V, • CAT IV 600 V Note: This adapter should not be used on low- voltage control circuits or where the circuit under test could be adversely-affected by this low impedance load The adapter is designed to handle continuously-applied power system voltages without damage However, this adapter can be used intermittently to determine whether a circuit is energised
Fluke Connect ® Wireless SD Card Wirelessly enable your Fluke Infrared Camera with the Fluke Connect ® Wireless SD card and you can instantly upload, share and analyse data from anywhere, with anyone on your team, at any time • The Wi-Fi SD Card is compatible with the following models: - Former Ti models: Ti90, Ti95, Ti100, Ti105, Ti110, Ti125, TiR105, TiR110, TiR125 - Current Ti models: TiX640, TiX660 and TiX1000 - Power Quality Analysers: 434 II, 435- II, 437-II, 438-II
FOS-850 and FOS-850/1300 Fiber Optic Light Source Both of these fiber optics accessories are designed to offer a variety of light sources for testing different cable lengths • Wave lengths: FOS-850: 850 nm; FOS-850/ 1300 850 and 1300 nm
Miscellaneous
VT04 Charger VT04 charger, power supply, USB socket plug and go 5 V DC 1 AMP 5 W
VT04 Battery Replacement Li-ion Rechargeable Battery for the VT04
156
Fluke Accessories
Made with FlippingBook Learn more on our blog