Fluke PCT Catalogue 2020

Electrical, Multifunction, and mA Loop Calibration

Data Acquisition

Pressure Calibration

Fluke Process Calibration Tools Catalogue

Temperature Calibration

Software/Accessories

Pressure Applications

Temperature Applications

Precision, performance, confidence.™ Process Calibration

Process Calibration Tools

Tools

Maximise uptime. Minimise downtime.

Why Calibrate? The need to achieve consistent results is one of the most important reasons why we calibrate. Accuracy is an important feature of a calibrator. You may need a particular level of accuracy to comply with standards that specify a test accuracy ratio (TAR) or test uncertainty ratio (TUR). For example, many standards require a 4:1 ratio between the specified tolerance of the device under test (DUT) and the accuracy or uncertainty of the calibration equipment. However, accuracy is also important because when accurate standards are used most of the time, downtime only needs to be long enough to verify that the instruments are still in tolerance. However, with inaccurate calibration standards, more borderline and out-of-tolerance indications are found. This means that a routine verification turns into an additional adjustment procedure and a final verification at each of the test points to prove the “as left” condition is in tolerance. This more than doubles the downtime and the technician time involved in completing the calibration. This is because inaccurate standards tend to not be consistent with each other causing us to make more adjustments to correct phantom errors.

Process Calibration Tools

PROCESS CALIBRATION

What issues do you face? • Complying with quality regulations • Maintaining documentation of processes Quality Manager Focus: Maintaining and documenting product quality

Instrumentation Technician

Maintenance Manager

Field Calibration Technician Focus: Calibrating and verifying measurement devices

Focus: Maintaining plant uptime and maintenance efficiency.

Focus: Maintaining and verifying instrumentation throughout the plant

What issues do you face? • Ensuring continuous uptime • Maintaining good ROI for equipment • Compliance • Process improvement • Increase efficiency

What issues do you face? • Making accurate measurements • Documenting procedures • Increasing throughput

What issues do you face? • Monitor and maintain sensors and transmissions • Accurate measurements

Bench Pressure Controller

Handheld Pressure Calibrators

Deadweight Testers

Pressure Gauge



6241

6532

3120

750

719PRO

721

729

700G

mA Loop Calibrator

Precision Multimeter

Process Calibrators

773

8846A

725

754

789

7526A

Infrared Calibrator

Temperature Readouts and Probes

Bench Temperature Sources

Software Solutions

4181

1524

PROBES

9100S

9144

DPC/TRACK2

Process Calibration Tools

SOLUTIONS



* Diagram is not intended to be an exact representation. Diagram components are not to scale and are for illustration purposes only.

Process Calibration Solutions Learn more Fluke Process Calibration Solutions at http://au.fluke.com/PCT Based on you. Built by Fluke

Process Calibration Tools

from Fluke and Fluke Calibration Working in a process environment such as pharmaceutical, refining or other industrial areas can be challenging. Whether you’re working at a bench, out in the plant, or in the field, you need accurate tools that you can count on. Finding the right tools for the specific challenges you face every day is important so we’ve provided an “at-a-glance” guide to the wide range of multifunction, mA loop, pressure and temperature calibrators that we carry. For complete information on our field and bench solutions to all your calibration needs visit http://au.fluke.com/PCT or one of the product pages listed in this catalogue.

Electrical and Multifunction Calibration Fluke offers a broad range of field and bench calibrators to source, simulate, and measure pressure, temperature and electrical signals to help you verify and adjust your test equipment or almost any process instrument.

mA Loop Calibration Loop calibrators are essential tools for working with 4-20 mA current loops. Fluke loop calibrators provide mA sourcing, simulation and measurement, readouts in both mA and % of span, 24 V loop supply, simple operation and accuracy you can count on.

Pressure Calibration Instrumentation is found in virtually every process plant. Periodic calibration of these instruments is required to keep plants operating efficiently and safely. Fluke provides a wide selection of field and bench calibration tools to help you quickly and reliably calibrate your pressure instrumentation.

Temperature Calibration Temperature calibration refers to the calibration of any device used in a system that measures temperature— from sensors to transmitters to displays. Fluke offers bench and field solutions to ensure process temperature accuracy of not only the system’s electronic temperature signals, but also the very temperature sensors that initiate those signals.

Process Calibration Tools

Thermometer Readouts.......................... 26 Precision PRTs. ............................. 27 Precision Industrial PRT......................... 27 Secondary Reference Temperature Standards.................................................. 27 Fast Response PRTs................................ 27 Secondary SPRT, PRT, Temperature Sensors...................................................... 27 Small Diameter Industrial RTD............. 27 Full Immersion PRT................................. 27 Thermistors................................... 27 Secondary Reference Thermistor Probes........................................................ 27

Liquid and Dirt Trap................................16 Hose Kit......................................................16 In-line Filter..............................................16 Hydraulic Test Hose.................................16 RTD Probe and Universal RTD Adapter............................16 Fluke 700MTH Premium Transmitter Test Hose Kit.............................................16 Fluke 700M20TH Premium Transmitter Test Hose Kit.............................................16 Current Shunt............................................16 Pressure Relief Valve Kit.........................16 Premium Transmitter Test Hose Kits....16 Pressure Comparators. .................. 17 Gas Pressure Comparators......................17 Hydraulic Pressure Comparators...........17 Pneumatic Test Pump Kit........................17 Bench Deadweight Testers............ 18 Single/Dual Piston Gas............................18 High Pressure Gas....................................18 Single/Dual Piston Oil. ............................18 High Pressure Oil......................................18 Single/Dual Piston Water........................18 Electronic Deadweight Testers...... 19 Electronic Deadweight Testers..............19

Electrical, Multifunction and mA Loop Calibration

Multifunction Calibrators................ 7 Documenting Process Calibrator........... 7 Documenting Process Calibrator with HART................................................. 7 Multifunction Process Calibrator........... 7 Precision Multifunction Process Calibrator.................................... 7 IS Multifunction Process Calibrator...... 7 Bench Digital Multimeter........................ 8 Precision Multimeters.............................. 8 Precision Process Calibrator................... 8 mA Loop Calibrators........................ 9 Precision Loop Calibrator..........................9 Precision Loop Calibrator with HART.....9 Loop Valve Tester.......................................9 Loop Calibrators..........................................9 IS Loop Calibrator.......................................9 Volt/mA Calibrator....................................10 ProcessMeter ™ Tools................................10 Milliamp Process Clamp Meters............10

Data Acquisition

Data Acquisition System.................29 Hydra Series III DAS/Digital Multimeter..................................................29 Super-DAQ Precision Temperature Scanner.......................................................29 Extra Universal Input Module.................29

Software

Temperature Calibration

Pressure Calibration

Software........................................31 750 SW DPC/TRACK2 Software ™ ..........31 700G/Track Logging Software..............31 LogWare.....................................................31 LogWare II..................................................31 LogWare III................................................31 MET/TEMP II Temperature Calibration Software.....................................................31 TQSoft and TQAero Thermal Validation Software.....................................................31

Handheld Temperature Calibrators and Dry-Wells ....................................... 22 RTD Process Calibrator........................... 22 Thermocouple Calibrator. ...................... 22 Temperature Calibrator...........................22 Handheld Dry-Wells ...............................22 Dual-Well Dry-Well ................................22 Multifunction Field Temperature Sources.......................................... 23 Field Metrology Wells.............................23 Field Dry-Wells........................................23 Thermocouple Furnace...........................23 Micro-Baths..............................................24 Portable Calibration Baths.....................24 Metrology Wells.......................................24 Infrared Temperature Sources....... 25 Precision IR Calibrators.......................... 25 Field IR Calibrators.................................. 25 Ambient Conditions Monitor.......... 25 Four-Channel Thermometer Readout.. 25 Precision Thermo-Hygrometer.............. 25 Thermometer Standards................ 26 Stik Thermometer.................................... 26 Handheld Thermometer Readout. ........ 26

Digital Pressure Calibrators. ......... 13 Automatic Pressure Calibrator...............13 Portable Electric Pressure Calibrator....13 Dual Range Pressure Calibrator............13 Pressure Calibrator...................................13 Pressure Calibrator with Pump..............13 IS Pressure Calibrator..............................13 Pressure Accessories and Test Pumps............................................ 14 Pressure Modules.....................................14 IS Pressure Modules.................................14 Hydraulic Test Pump................................14 Pneumatic Test Pump..............................14 Low Pressure Test Pump.........................14 Test Pressure Kits ...................................14 Master Gauges and Reference Pressure Calibrators ..................... 15 Industrial Pressure Calibrator................15 Precision Pressure Gauges. ....................15 Reference Pressure Gauges....................15 Portable Pressure Calibrator..................15 Pressure Accessories. ................... 16

Applications

Pressure Applications.....................32 Temperature Applications...................................52

Process Calibration Tools

Electrical, Multifunction and mA Loop Calibration

Process Calibration Tools

These field and bench calibrators source, simulate, and measure pressure, temperature and electrical signals with exceptional precision. Multifunction Calibrators

753 Documenting Process Calibrator Rugged handheld tool for sourcing, simulating and measuring pressure,

754 Documenting Process Calibrator with HART ® Rugged, reliable tool for calibrating, maintaining and troubleshooting

temperature, and electrical signals.

HART and other instrumentation.

• Measure volts, mA, RTDs, thermocouples, frequency and ohms to test sensors, transmitters and other instruments • Source/simulate volts, mA, thermocouples, RTDs, frequency, ohms and pressure to calibrate transmitters • Power transmitters during test using loop supply with simultaneous mA measurement • Download procedures and upload calibration results from field calibrations • NIST traceable calibration www.fluke.com/au/753

• Measure volts, mA, RTDs, thermocouples, frequency and ohms to test sensors, transmitters and other instruments • Source/simulate volts, mA, thermocouples, RTDs, frequency, ohms and pressure to calibrate transmitters • Supports popular models of HART transmitters, with more device-specific command support than any other HART field calibrator • Download procedures and upload calibration results from field calibrations • NIST traceable calibration www.fluke.com/au/754

726 Precision Multifunction Process Calibrator Designed specifically for the process industry with broad workload coverage, calibration power and unsurpassed accuracy. Includes all the features and functions of the 725 plus: • Enhanced accuracy • Pulse count sourcing and pulse measurement totalising • Pressure switch test • Error % calculation • NIST traceable calibration www.fluke.com/au/726

725 Multifunction Process Calibrator A powerful and easy-to-use field calibrator to test and calibrate almost any process parameter. • Measure/source/simulate volts, mA, thermocouples, RTDs, frequency, ohms, and pressure to calibrate transmitters • Measure/source pressure using any of 48 Fluke 750P Pressure Modules • Source mA with simultaneous pressure measurement to conduct valve and I/P tests • NIST traceable calibration www.fluke.com/au/725

725Ex IS Multifunction Process Calibrator

Easy-to-use, intrinsically safe field calibrator can calibrate almost any process instrument needing service where explosive gasses may be present. Includes all the features and functions of the 725 plus: • ATEX II 1 G Ex ia IIB 171°C KEMA 04ATEX 1303X • I.S. Class I, Division 1 Groups B-D, 171°C compliance • Measure/source pressure using any eight Fluke 750PEx Pressure Modules www.fluke.com/au/Ex

7 7

Electrical, Multifunction and mA Loop Calibration

Bench Calibrators

Digital and Precision Bench Multimeters and Precise Process Calibrator.

7526A Precision Process Calibrator Best balance of economy and accuracy for calibration of temperature and pressure process measurement instrumentation. • Sources and measures DC voltage, current, resistance, RTDs and thermocouples • Measures pressure using Fluke 700/525A-P pressure modules • Includes 24 V DC loop power supply, automated switch-test function and measures 4 mA to 20 mA • NIST traceable calibration au.flukecal.com/7526A

8845A/8846A 6.5 Digit Precision Multimeters Precision and versatility for bench or systems applications. • 6.5 digit resolution • Basic V DC accuracy of up to 0.0024% • Dual display • 100 μA to 10 A current range, with up to 100 pA resolution • Wide ohms range from 10 Ω to 1 GΩ with up to 10 μΩ resolution • 2 x 4 ohms 4-wire measurement technique • Both models measure frequency and period • 8846A also measures capacitance and temperature • Accredited calibration www.fluke.com/au/8845A

8808A Digital Multimeter Versatile multimeter for manufacturing, development and service applications. • 5.5 digit resolution • Basic V DC accuracy of 0.015% • Dual display • Dedicated dc leakage current measurement • 2x4 ohms 4-wire measurement technique • Six dedicated buttons for fast access to instrument setups • Hi/Lo limit compare for Pass/Fail testing • 3 year warranty • NIST traceable calibration www.fluke.com/au/8808A

By combining the automating and documenting capabilities of the Fluke 754 Documenting Process Calibrator with Fluke Calibration’s intelligent and stable family of field drywells and micro-baths, you have the capability to test the entire loop. This combination of equipment allows you to easily verify the characteristics of the temperature sensor and measurement electronics. Using this information, the entire loop can be adjusted to optimise system measurement performance. Fluke 754 with 914X Series Field Metrology Well Complete Solution

Electrical, Multifunction and mA Loop Calibration

Fluke Loop Calibrators are ideal for a wide variety of calibration applications from 4 to 20 mA. mA Loop Calibrators

709 Precision Loop Calibrator

709H Precision Loop Calibrator with HART Communications/ Diagnostics

710 mA Loop Valve Tester Designed to enable users to perform quick, easy tests on HART smart control valves. • Key valve testing functions include pre-configured valve signature test, speed test, step test, manual test, and bump/partial stroke test • Key mA loop calibrator functions include mA source, mA simulate, mA read, mA read/loop power, and volts read • ValveTrack™ Software enables upload to a PC for further in-depth analysis of valve measurements that are logged and recorded to memory www.fluke.com/au/710

Reduces the time it takes to measure or source voltage or current and power up a loop. • Best-in-class accuracy at 0.01% reading • Small rugged design • Intuitive user interface with Quick-Set knob for fast setup and easy use • Built-in selectable 250 Ω resistor for HART communication • 24 V DC loop power with mA Measure Mode (-25% to 125%) • Resolution of 1 µA on mA ranges and 1 mV on voltages ranges www.fluke.com/au/709

Designed to save time and produce high-quality results. • HART Communication built in for easy HART device maintenance • Best-in-class accuracy at 0.01% reading • Small rugged design operates on six standard AAA batteries • Intuitive user interface with Quick-Set knob for fast setup and easy use • Built-in selectable 250 Ω resistor for HART communication www.fluke.com/au/709H

707 Loop Calibrator A high performance, extremely fast and easy-to-use solution for calibration, repair and maintenance of current loops. • mA sourcing, simulation and measurement • 24 V loop supply with mA measure, including 250 Ω HART resistor • 0 V DC to 28 V DC measurement to check loop voltage • NIST traceable calibration www.fluke.com/au/707

705 Loop Calibrator A cost-effective, integrated solution for calibration, repair and maintenance of current loops. • mA sourcing, simulation and measurement • Simultaneous mA and % of span display • 24 V loop supply with mA measure • 0 V DC to 28 V DC measurement to check loop voltage • NIST traceable calibration www.fluke.com/au/705

707Ex IS Loop Calibrator An intrinsically safe loop calibrator for use in explosion endangered areas. Certified in accordance with the ATEX directive in Zones 1 and 2. • Measures V DC to 28 V • 0-20 mA or 4-20 mA default startup modes • HART ® compatible resistance is connected in series with the loop supply for compatibility with HART communicators www.fluke.com/au/Ex

Electrical, Multifunction and mA Loop Calibration

Process Meters and Clamp Meters

Provide the versatility of a digital multimeter and loop calibrator and save time with no need to break the loop.

787B ProcessMeter ™ Double troubleshooting capabilities by combining the power of a digital multimeter and mA loop calibrator into one tool. • 20 mA DC current source/ measure/simulate • Simultaneous mA and % of scale readout • Fluke Connect ® compatibility for wireless data logging (with IR3000FC module) • Precision 1000 V, 440 mA true-rms digital multimeter • Frequency measurement to 20 kHz www.fluke.com/au/787B

715 Volt/mA Calibrator Outstanding performance, durability and reliability.

789 ProcessMeter ™ The 789 includes all the popular features of the 787 and adds: • 24 V loop power supply • 1200 ohm drive capability on mA source • HART mode setting with loop power and a built-in 250 ohm resistor • 0% and 100% buttons to toggle between 4 and 20 mA sourcing for a quick span check

• Measure loop current (0-20 mA, 4-20 mA) signals with very high accuracy of 0.015% and 1 mA resolution • Measure voltage output process signals from PLCs, transmitters • Source or simulate 24 mA loop current • Source voltage to 100 mV or 10 V • 24 V loop supply with simultaneous current measurement • Enhanced voltage and current measure and source accuracy • NIST traceable calibration www.fluke.com/au/715

• CAT IV 600 V rating www.fluke.com/au/789

772 Milliamp Process Clamp Meter

771 Milliamp Process Clamp Meter Saves time by making fast,

773 Milliamp Process Clamp Meter

Expanded features of the popular 771 mA clamp meter by adding loop power and mA sourcing to the capabilities. • Measure 4 to 20 mA signals with in-circuit measurement • Simultaneous mA in-circuit measurement with 24 V loop power for powering and testing transmitters • Source 4 to 20 mA signals for testing control system I/O or I/Ps • Automatically ramp or step the 4 to 20 mA output for remote testing www.fluke.com/au/772

The premier mA clamp meter, adds advanced troubleshooting features and voltage source/ measure for testing voltage I/O. Includes all the features of the 772 plus: • DC voltage sourcing and measurement, verify 24 V power supplies or test voltage I/O signals • Scaled mA output provides a continuous mA signal that corresponds to the 4 to 20 mA signal measured by the mA clamp • Simultaneously source and measure mA signals www.fluke.com/au/773

accurate measurements on 4-20 mA signal loops without breaking the circuit. • 0.01 mA resolution and sensitivity • Measure mA signals for PLC and control system analog I/O • Measure 10 to 50 mA signals in older control systems using the 99.9 mA range www.fluke.com/au/771

Electrical, Multifunction and mA Loop Calibration

Process instrumentation requires periodic calibration and maintenance to ensure that it is operating correctly.

Field checking a loop-powered isolator Fluke loop calibrators have a unique current simulation feature that, when connected to an external power source, allows you to precisely control current between 0 mA and 24 mA. When field checking a loop-powered isolator, the two-wire loop transmitter supplying signal current to the isolator for the loop may be removed and the calibrator connected in simulate mode to control loop current.

Testing valve positioners Electronic valve positioners should receive periodic in-field calibrations as part of preventive maintenance programs. Fluke loop calibrators are the ideal test tools for these checks. Valve positioners vary in design and valve type and should be calibrated using specific instructions from the individual manufacturer. Quick operational checks can be performed using a field calibrator as a signal source while observing the valve stem position, mechanical position indicators or flow indicators as input changes are made. Fluke loop calibrators provide a convenient source for simulating the controller output to a valve positioner.

Using Fluke Loop Calibrators as a voltage source A precision shunt resistor may be used to derive voltages for calibration using the calibrator’s current source mode. Using this system, Fluke loop calibrators are capable of generating voltages for devices with input spans as low as 10 mV to as high as 24 V.

Pressure Calibration

Built-in features like mA measure, loop power, switch test and transmitter error calculation make these pressure calibrators powerful tools that are easy to use. Digital Pressure Calibrators

729 Automatic Pressure Calibrator Portable automatic pressure calibrator simplifies pressure calibration. • Automatic pressure generation and regulation to 20 bar • Easily document the process using onboard test templates • Automatic internal fine-pressure adjustment • Measure, source and simulate 4 to 20 mA signals • 24V loop power for powering transmitters for tests • HART communication for testing HART smart transmitters www.fluke.com/au/729

719 Portable Electric Pressure Calibrator

719Pro Portable Electric Pressure Calibrator Calibrate and test pressure devices quickly with the built-in electric pump. • Source mA with simultaneous pressure measurement to test valves and I/Ps • Power transmitters during test using 24 V loop supply with simultaneous mA measurement • New 300 psi range, generate up to 300 psi, with internal electric pump

721 Dual Range Pressure Calibrator Two measurement ranges plus temperature measuremen • Up to three displayed measurements simultaneously • High accuracy, 0.025% total measurement uncertainty for one year • Pt100 RTD input for precise temperature measurement, accurate to 0.1°C • NIST traceable calibration www.fluke.com/au/721

Calibrate and test pressure devices quickly and easily with one hand, saving valuable time. • Simulates mA signals to troubleshoot 4-20 mA loops • Powers transmitters during test using 24 V loop supply • Offers ideal performance for high accuracy transmitter calibration www.fluke.com/au/719

• NIST traceable calibration www.fluke.com/au/719Pro

718 Pressure Calibrator with Pump

717 Pressure Calibrator Rugged, reliable and accurate calibrator with outstanding performance and durability. • Measure pressure, 0.025% of full scale with internal sensor up to 10,000 psi/690 bar sensor (10000G model) • Measure mA with 0.015% accuracy and 0.001 mA resolution, while sourcing 24 V loop power • NIST traceable calibration www.fluke.com/au/717

718Ex IS Pressure Calibrator A powerful, intrinsically safe and self-contained pressure calibrator for use in explosion endangered areas. • ATEX II 1G Ex ia IIC T4 compliant • Built-in pressure/vacuum hand pump, with fine adjust vernier and bleed valve • 30 psi, 100 psi, and 300 psi ranges • NIST traceable calibration www.fluke.com/au/Ex

Provides a total pressure calibration solution for transmitters, gauges and switches. • Pressure source and milliamp measurement to calibrate and maintain almost any pressure device • 1 psi, 30 psi, 100 psi and 300 psi ranges mean few extra tools required • NIST traceable calibration www.fluke.com/au/718

Pressure Modules and Accessories

Get outstanding value with our most rugged modules.

750P Pressure Modules A full range of differential, gage, absolute, vacuum, dual and intrinsically safe pressure modules are available, from 2.5 mBar to 690 Bar.

750PEx Pressure Modules The ideal pressure modules to enable gage, differential and absolute pressure measurement with Fluke 750 DPCs and 725, 726 MPCs to measure pressure.

• Improved total uncertainty with reference class accuracies as good as 0.01% • Enhanced connectability with easy to connect finger-tight adapters for NPT, BSP and M20 fittings (supplied) • Multiple temperature specification windows offering additional specification improvements • Absolute pressure measurement now to 1,500 PSIA, 100 bar www.fluke.com/au/750P

• Up to 0.01 % reference uncertainty • 6-month and 1-year specifications • Temperature compensated 0 °C to 50 °C • Broad selection of ranges • Eight (8) Intrinsically Safe models that are certified to: - NEC-500: Class I Div 1, Groups A-D, Ga - ATEX: II 1 G Ex ia IIC T4 Ga - IECEx: Ex ia IIC T4 Ga www.fluke.com/au/750PEx

700HTP-2 Hydraulic Test Pump Designed to generate pressures up to 10,000 psi/700 bar. • Generate pressure up to 10,000 psi, 690 bar with the included 700HTP-2 test pump • Connect the 700G Series gauge directly to the HTP-2 hand pump www.fluke.com/au/process_acc

700PTP-1 Pneumatic Test Pump Designed to generate either vacuum to -11.6 psi/-0.8 bar or pressure to 600 psi/40 bar. • Generate pressure up to 600 psi, 40 bar with the 700PTP-1 test pump • Connect the 700G Series gauge directly to the included PTP-1 hand pump www.fluke.com/au/process_acc

700LTP-1 Low Pressure Test Pump

Hand operated pressure pump designed to generate either vacuum to -13 psi/-.90 bar or pressures to 100 psi/6.9 bar. Ideal for low pressure applications requiring accurate low pressure testing. www.fluke.com/au/process_acc

700PTPK2 Pneumatic Test Kit • Combine with any Fluke 700G Series Gauge, 1,000 psi (69 bar) or less, to make a complete pressure testing kit • Generate pressure up to 600 psi, 40 bar with 700PTP-1 Test Pump www.fluke.com/au/process_acc

700HTPK2 Hydraulic Test Kit • Combine with any Fluke-700G Series Gauge, 1,000 psi (69 bar) range or greater, to make a complete pressure testing kit • Generate pressure up to 10,000 psi, 690 bar www.fluke.com/au/process_acc

700PMP Pressure Pump The 700PMP is a hand-operated pressure pump to provide pressures up to 10 bar. Output fittig is 1/8 FNPT. www.fluke.com/au/process_acc

Pressure Calibration

Portable, high-quality pressure calibrators and precision pressure gauges. Master Gauges, Manual and Reference Pressure Calibrators

2271A Industrial Pressure Calibrator Everything you need to calibrate and test pressure transmitters and gauges from very low pressure to 3000 psi (20 MPa), all in one box • Calibrate a wide range of gauges and sensors with a single instrument • Two levels of accuracy, 0.01% reading or 0.02% FS • Wide measurement range from -100 kPa to 20 MPa (-15 to 3000 psi) • Removable pressure measurement modules make it easy to change or add measurement ranges • Integrated electrical measurement module with HART communication provides a complete solution for calibrating pressure transmitters • Built-in dual test ports enable you to connect multiple devices under test (DUTs) au.flukecal.com/2271A

700G Precision Pressure Gauges Rugged construction for reliable measurements in the field. • Twenty-three ranges from 15 psi/1 bar to 10,000 psi/690 bar and 0.05 % accuracy • Combine with a comparator kit for a complete solution • Four absolute pressure measurement ranges • Use the 700G/TRACK Software to upload over 8,000 logged pressure measurements • Up to 1500 hours battery life • I.S. rating, CSA; Class 1, Div 2, Groups A-D rating, ATEX: rating: II 3 G Ex nA IIB T6 • NIST traceable calibration www.fluke.com/au/700G

2700G Series Reference Pressure Gauges Best-in-class accuracy from a master pressure gauge. • Precision pressure measurement from 100 kPa (15 psi) to 70 MPa (10,000 psi) • Accuracy to ± 0.02% of full scale • Combine with the 700PTPK or 700HTPK pump kits for a complete portable pressure testing solution for up to 4 MPa (600 psi) with the PTP-1 pneumatic pump and up to 70 MPa (10 000 psi) with the HTP-2 hydraulic pump • Optional accredited calibration au.flukecal.com/2700G

3130 Portable Pressure Calibrator Everything you need for highly accurate calibrations of pneumatic field instruments. • Measure and generate pressures from -12 psi (0.8 bar) to 2 MPa (300 psi, 20 bar) • Accuracy of ±0.025% reading to ±0.01% FS • Works with compressed plant air internal pump • 24 V loop power and electrical measurement for transmitters and switches • Compatible with Fluke 750P pressure modules • NiMH battery au.flukecal.com/3130

Pressure Calibration

Accessories increase the functionality of your test tool and increase your safety and proficiency. Pressure Tools Accessories

71XTrap Liquid and Dirt Trap • Works with pressure up to 500 psi • Designed to work with the Fluke 718 and 719PRO www.fluke.com/au/process_acc

71X, Hose Kit • Compatible with Fluke 717 and 718 Calibrators 100 PSI and below • Kit contains three translucent hoses (1 m long) and one 1/8 to ¼ NPT female-female adapter www.fluke.com/au/process_acc

700ILF In-line Filter • Can be used to isolate the calibrator from incidental contact with fluids • Useful with the 718 Fluke Calibrator to help keep moisture or oils from contaminating the on-board pump www.fluke.com/au/process_acc

700HTH-1 Hydraulic Test Hose • 10,000 psi, 690 bar working pressure test hose www.fluke.com/au/process_acc

720RTD RTD Probe Fluke-720RTD Temperature Probe is for use with Fluke 721 and 719Pro Pressure Calibrators • 10 inch (254mm) insertion depth with 1 inch (6.3mm) diameter stainless steel sheath www.fluke.com/au/process_acc

720URTDA Universal RTD Adapter Fluke Universal RTD Adapter 720URTDA for Fluke 721 Precision Pressure Calibrators and Fluke 719Pro Electric Pressure Calibrators www.fluke.com/au/process_acc

Fluke 700MTH Premium Transmitter Test Hose Kit Easy to use premium pressure transmitter test hose kit for connection to 1/4" female metric/BSP • 5,000 psi rating • Includes 1/8" NPT connection for permanent mount to a calibrator or test pump www.fluke.com/au/process_acc

Fluke 700M20TH Premium Transmitter Test Hose Kit Easy to use premium pressure transmitter test hose kit for use with female M20 connections Includes: • One (1) 5,000 psi rated, premium test hose • Premium, no tools required M20 adapter www.fluke.com/au/process_acc

700-IV Current Shunt • Conversion factor: 10 mV = 1 mA • Accuracy (% of input, one-year): 0.025 %

• Input current: 0 mA to 55 mA • Input resistance: 250 Ω nominal • Output resistance: 10 Ω nominal • Accuracy specification applies from +18 °C and 28 °C to 50 °C • Maximum input voltage: 30 V DC www.fluke.com/au/process_acc

700PRV Pressure Relief Valve Kit

• Consists of a relief valve settable from 725 to 5800 PSI to be used with the 700HTP-1 Test Pump • The 1/8” NPT male thread to fits directly into the Fluke 700HTP-1 Pressure Pump www.fluke.com/au/process_acc

Pressure Calibration

Precise pressure generation for comparing a device under test to a master gauge. Pressure Comparators

P5510 Gas Pressure Comparator

P5513 Gas Pressure Comparator High quality, precise gas

P5514 Hydraulic Pressure Comparator Easy, efficient hydraulic pressure generation.

Easy, efficient pressure and vacuum generation in a single device. • Pressure to 2 MPa (300 psi) • Vacuum to -80 kPa (-12 psi) au.flukecal.com/P5510

pressure generation and control. • Precise pressure regulation to 210 MPa (3,000 psi) with high quality needle valves • Built-in screw press for fine pressure adjustment au.flukecal.com/P5513

• Generate and precisely adjust pressure to 70 MPa (10,000 psi) • Compatible with a wide range of fluids au.flukecal.com/P5514

P5515 Hydraulic Pressure Comparator High quality, precise hydraulic pressure generation and control. • Generate and precisely adjust pressure to 140 MPa (20,000 psi) • Integrated hand pump for system priming and large volume applications au.flukecal.com/P5515

700HPPK Pneumatic Test Pump Kit Rugged and portable way to generate pressure in the field quickly, safely and easily. • Generates and adjusts pneumatic pressure up to 21 MPa • Reaches pressure in 20 seconds to full scale into a 30 cm 3 volume au.flukecal.com/700HPPK

Complete Bench Top Pressure Calibration Solution Combine P5500 comparison test pumps with one or more 2700G reference pressure gauges for a complete 0.02% accuracy calibration system.

The 2700G has an easy-to-use interface that allows you to configure the sampling rate, tare value, damping and auto off time interval as well as reset the min/max pressure. You can also view the remaining battery life. Select from 21 different standard engineering units, including bar, in H2O, kPa, MPa and psi. The 2700G Reference Pressure Gauge can be combined with the Fluke Calibration P5500 series of comparison test pumps to make a complete pressure calibration system. The unique test port design of the P5500 series allows for hand tight connection of the 2700G without the use of PTFE tape.

Pressure Calibration

Deadweight testers are highly accurate, robust and flexible pressure measurement standards capable of calibrating a wide range of instruments. Bench Deadweight Testers

P3010 Single Piston Gas Deadweight Tester A high quality, high performance gas deadweight tester. • 0.015 % of reading accuracy (0.008 % optional) • Ranges cover from -100 kPa vacuum to 3.5 MPa pressure • Integrated vacuum/pressure pump available to 2 MPa

P3020 Dual Piston Gas Deadweight Tester Unique suspended piston design offers vacuum and pressure calibration in a single instrument. • 0.015 % of reading accuracy (0.008 % optional) • Ranges cover from 1.5 kPa to 3.5 MPa • All models feature vacuum measurement to -100 kPa • Integrated vacuum/pressure pump available to 2 MPa

P3030 High Pressure Gas Deadweight Tester Innovative liquid-lubricated piston offers low drop rates and high tolerance to contamination. • 0.015 % of reading accuracy (0.008 % optional) • Ranges cover from 100 kPa to 14 MPa • Integrated control valves and screw press for fine adjustment

• Accredited calibration au.flukecal.com/P3010

• Accredited calibration au.flukecal.com/P3030

• Accredited calibration au.flukecal.com/P3020

P3110 Single Piston Oil Deadweight Tester High quality, high performance, easy to use oil pressure calibration. • 0.015 % of reading accuracy (0.008 % optional) • Ranges cover from 100 kPa to 140 MPa • Integrated pressure generation

P3120 Dual Piston Oil Deadweight Tester Dual piston design offers

P3210 Single Piston Water Deadweight Tester Specially designed to use water as a test medium. • 0.015 % of reading accuracy (0.008 % optional) • Ranges cover from 100 kPa to 70 MPa • Integrated pressure generation

maximum hydraulic pressure calibration workload coverage. • 0.015 % of reading accuracy (0.008 % optional) • 100 kPa to 110 MPa in a single instrument • Integrated pressure generation

and control is standard • Accredited calibration au.flukecal.com/P3110

and control is standard • Accredited calibration au.flukecal.com/P3210

and control is standard • Accredited calibration au.flukecal.com/P3120

P3220 Dual Piston Water Deadweight Tester Dual piston design offers maximum water pressure calibration workload coverage. • 0.015 % of reading accuracy (0.008 % optional) • 100 kPa to 70 MPa in a single instrument • Integrated pressure generation and control is standard

P3800 High Pressure Oil Deadweight Tester High performance, easy to use very high pressure oil calibration. • 0.02% of reading accuracy (0.015% optional) • Ranges up to 400 MPa (60,000 psi) • Integrated pressure generation, intensifier and control

• Accredited calibration au.flukecal.com/P3220

• Accredited calibration au.flukecal.com/P3800

Pressure Calibration

Electronic Deadweight Testers

High performance, with powerful features for a wide range of pneumatic pressure calibrations.

6531 Electronic Deadweight Tester A digital alternative to the traditional deadweight tester. • 0.02% of reading from 10% to 100% of instrument range (10:1 turndown) • Ranges from 7 MPa (1000 psi) to 200 MPa (30,000 psi) • Integrated hydraulic pressure generation and control • Compatible with water and a wide range of oils and other fluids • Onboard test routines, data storage, and

6532 Extended Range Electronic Deadweight Tester All the features of model 6531 with extended pressure range for maximum workload coverage. • 0.02% of reading from 1% to 100% of instrument range (100:1 turndown) • Models with full scale ranges from 70 MPa (10,000 psi) to 200 MPa (30,000 psi)

• Accredited calibration au.flukecal.com/6532

other advanced features • Accredited calibration au.flukecal.com/6531

19 19

Pressure Calibration

A pressure calibration system needs to accurately measure pressure and may also need to measure pressure transmitters.

A complete pressure calibration system includes components to generate, control and measure pressure (and normally to log data from some or all of these functions). Some systems include two or all of these functions in a single unit. A procedure to adjust the unit is also usually required. Pressure monitors and references are digital readouts or gages that convert the pressure into numerical pressure units. Pressure sources generate either pneumatic (gas) or hydraulic (oil, water or alcohol typically) pressure.

For PCT field applications, a hand-pump or comparison test pump can be used, in conjunction with a reference calibrator; these normally provide sufficient control for field applications. On the bench, for higher pressures and where a greater degree of control or automation is required, a gas bottle or shop air can be used with a controller. Deadweight testers and the related electronic deadweight tester are portable systems that provide all three functions: generation, control and measurement— in a single unit and are suitable for both field and bench use.

Analogue and digital pressure gauges are often used to monitor pressures in processes. Gages have an internal mechanical or electro-mechanical mechanism to convert input pressure to a reading. Sensors and transmitters comprise both a sensor assembly, to detect and measure the pressure, and a transmitter, which converts the pressure into an electrical signal, typically a 4-20 milliamp signal, that can be transmitted to a control panel, PLC or other readout.

Pressure Calibration

Temperature Calibration

Handheld Temperature Calibrators

Suitable for calibrating temperature transmitters, panel meters and other devices that connect to temperature sensors.

712B RTD Calibrator Ideal tool for temperature

724 Temperature Calibrator Powerful and easy-to-use to measure and source functions for testing and calibrating almost any temperature instrument. • Measure RTDs, thermocouples, ohms, and volts to test sensors and transmitters • Source/simulate thermocouples, RTDs, volts, and ohms to calibrate transmitters • Perform fast linearity tests with 25% and 100% steps • NIST traceable calibration www.fluke.com/au/724

714B Thermocouple Calibrator

calibration professionals offering a highly accurate easy-to-use single function RTD temperature calibrator. • The 712B measures and simulate (13) different RTD types and resistance • Measure 4 to 20 mA signals while simultaneously sourcing a temperature signal • Configurable 0% and 100% source settings for quick 25% linearity checks • Linear ramp and 25% step auto ramp based on 0% and 100% settings • 1-year and 2-year specifications and traceable certificate of calibration www.fluke.com/au/712B

Highly accurate, easy-to-use single function thermocouple temperature calibrator. • The 714B measures and simulates (17) different thermocouple types and millivolts • Measure 4 to 20 mA signals while simultaneously sourcing a temperature signal • Configurable 0% and 100% source settings for quick 25% linearity checks • Linear ramp and 25% step auto ramp based on 0% and 100% settings • 1-year and 2-year specifications and traceable certificate of calibration www.fluke.com/au/714B

Field Temperature Sources

Portable and flexible temperature-controlled dry-wells suitable for high-speed calibrations or certifications of thermocouples, RTDs, PRTs and other temperature sensors.

9102S Handheld Dry-Well High-performance, convenient and easy-to-use handheld dry-well. • Smallest dry-wells in the world • Ranges from –10°C to 122°C • Accuracy to ± 0.25°C, stability of ± 0.05°C (full range) • NIST traceable calibration au.flukecal.com/9102S

9009 Dual-Well Dry-Well Two-in-one dry-well increases portability and productivity. • Temperatures from –15°C to 350°C in one unit • Display accuracy: hot block: ± 0.6°C; cold block: ±0.2°C • Rugged, lightweight, water resistant enclosure • NIST traceable calibration au.flukecal.com/9009

9100S Handheld Dry-Well World’s smallest, lightest and most portable dry-well. • Smallest dry-wells in the world • Ranges from 35°C to 375°C • Accuracy to ± 0.25°C, stability of ± 0.07°C at 50°C • NIST traceable calibration au.flukecal.com/9100S

Temperature Calibration

Fast, lightweight and portable with precision temperature control traceable to National Standards. Suitable for calibration of thermocouples, RTDs, PRTs and other temperature sensors. Multifunction Field Temperature Sources

914X Series Field Metrology Wells The 914X series field metrology wells extend high performance to the industrial process environment by maximising portability, speed and functionality with little compromise to metrology performance. Field metrology wells are lightweight, small and quick to reach temperature set points yet also stable, uniform and precise. This industrial product line is perfect for transmitter loop, comparison calibration, or a simple check of a thermocouple sensor. There is no need to carry additional tools into the field as the “process” option offers a built-in readout for resistance, voltage and mA measurement, 24V loop power and on-board documentation.

9144 Field Metrology Well Precision calibration with fast temperature ramp-up rates for the industrial process environment. • 50°C to 660°C temperature range • Heat to 660°C in 15 minutes • Display accuracy from ± 0.35°C at 420°C to ± 0.5°C at ± 660°C • Optional built-in reference thermometer readout

9143 Field Metrology Well Extend high performance to the industrial process environment with little compromise to metrology performance. • 33°C to 350°C temperature range • Display accuracy of ± 0.2°C over full range • Built-in two-channel readout for PRT, RTD, thermocouple, 4-20 mA current • Optional built-in reference thermometer readout

9142 Field Metrology Well Maximising portability, speed, and functionality for the industrial process environment. • –25°C to 150°C temperature range • Display accuracy of ± 0.2°C over full range • Built-in two-channel readout for PRT, RTD, thermocouple, 4-20 mA current • Optional built-in reference thermometer readout

• Accredited calibration au.flukecal.com/9144

• Accredited calibration au.flukecal.com/9143

• Accredited calibration au.flukecal.com/9142

9103 Field Dry-Well Great performance in a portable instrument. • –25 °C to 140 °C • Accuracy to ± 0.25 °C • Stable to ± 0.02 °C at –25 °C and ± 0.04 °C at 140 °C • NIST traceable calibration au.flukecal.com/9103

9140 Field Dry-Well Lightweight and portable field dry-well small enough to easily carry in one hand. • 35 °C to 350 °C • Accuracy to ± 0.5 °C • Stability to ± 0.03 °C at 50 °C and ± 0.05 °C at 350 °C • NIST traceable calibration au.flukecal.com/9140

9150 Thermocouple Furnace Convenient, portable thermocouple furnace. • 150 °C to 1200 °C • Stability of ± 0.5 °C over full range • RS-232 port standard • NIST traceable calibration au.flukecal.com/9150

Temperature Calibration

9190A Ultra-Cool Field Metrology Well Very low temperatures, with no fluids and best-in-class stability • Wide temperature range from –95°C to 140°C • Best-in-class stability: ± 0.015°C full range • Accuracy using built-in reference thermometer readout: ± 0.05°C full range • Display accuracy: ± 0.2°C full range • Optional built-in two-channel readout for PRT, RTC, TC, 4-20 mA and

reference thermometer • Accredited calibration au.flukecal.com/9190A

6109A/7109A Portable Calibration Baths

6102/7102/7103 Micro-Baths Calibrate a variety of probe diameters—no sleeves required. • Three models covering temperatures from –30°C to 200°C • World’s smallest portable calibration baths • Stability to ± 0.015°C • NIST traceable calibration au.flukecal.com/micro-baths

Calibrate up to four tri-clamp sanitary sensors, or a batch of sanitary RTDs and temperature transmitters, at the same time. • Wide temperature range covers most clean process applications: • Excellent display accuracy of ± 0.1°C provides 4:1 test uncertainty ratio (TUR) for critical applications • Easy to transport up stairs and across catwalks • Stainless steel casing withstands harsh sterilising chemicals and is rust proof perfect for clean room use • Easy to use and maintain au.flukecal.com/6109A -6109A: 35°C to 250°C -7109A: –25°C to 140°C

Temperature Calibration

Infrared Temperature Sources

Bench and field precision infrared calibrators for accurate and reliable calibrations of infrared thermometers.

9132/9133 Field Infrared Calibrators Precision when you need it for infrared temperature calibration. • Verify IR pyrometers from –30°C to 500°C • RTD reference well for contact temperature measurement • Small compact design • NIST traceable contact calibration au.flukecal.com/913X

4180/4181 Precision Infrared Calibrators Accredited performance for point and shoot calibrations. • Calibrated radiometrically for meaningful, consistent results • Accurate, reliable performance from –15°C to 500°C • Large 152mm diameter target

• Accredited calibration au.flukecal.com/418X

For precise measurement and recording of ambient temperature and humidity conditions wherever calibrations take place. Ambient Conditions Monitor

1529 Four-Channel Thermometer Readout Lab-quality accuracy on four channels for PRTs, thermistors and thermocouples. • Accuracy of ±0.0025°C (meter only) • Displays eight user-selected data fields from any channel • Logs up to 8,000 readings with date and time stamps

1620A Precision Thermo-Hygrometer

The most accurate temperature and humidity graphical data logger on the market. • Superior accuracy • Network enabled • Powerful logging and analysis tools

• Measures temperature to ± 0.125°C and humidity to ± 1.5% on two channels • NIST-traceable NVLAP accredited temperature and humidity calibration au.flukecal.com/1620A

• Accredited calibration au.flukecal.com/1529

Temperature Calibration

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46 Page 47 Page 48 Page 49 Page 50 Page 51 Page 52 Page 53 Page 54 Page 55 Page 56 Page 57 Page 58 Page 59 Page 60 Page 61 Page 62 Page 63 Page 64 Page 65 Page 66 Page 67 Page 68 Page 69 Page 70 Page 71 Page 72 Page 73 Page 74 Page 75 Page 76

www.fluke.com

Made with FlippingBook Learn more on our blog