29 D
10-PC. FLARE NUT SOCKET SET Works on ABS, master cylinder, coolant, and diesel injection sensors. 3/8” square drive with chrome finish.
WATER PUMP SPROCKET HOLDER - ECOTEC Securely holds water pump sprocket pre- venting loss of timing or damage to the engine. Special half-moon design allows easier access to water pump gear bolts. Uses access cover bolts to hold the tool in place
IPR SOCKET FOR FORD 6.0L AND INTERNATIONAL DIESEL Used to remove and replace the injector pressure regulator (IPR) on Ford 6.0L, international and other diesel engines. This regulator is located in a very tight location. The tool is built to bottom out on the regulator hex so it does not put torque on the connector in case the regulator can be reused. Use with 3/8” square drive
Set includes: 10mm, 11mm, 12mm, 13mm, 14mm, 15mm, 16mm, 17mm, 18mm and 19mm
LIS-12030.......................................................$187.99 LIS-13180 7-Pc. SAE .........................................$142.69
LIS-13800........................................................ $41.49
LIS-68210.........................................................$31.99
11-PC. OXYGEN SENSOR & SENDING UNIT SOCKET SET • Includes a variety of socket & wrenches for use
FORD DIESEL FUEL FILTER WRENCH • Used for removal and installation on the Ford Power Stroke® diesel and International/Navistar diesel engines
UNIVERSAL CAMSHAFT BEARING TOOL
VARIABLE PIN SPANNER WRENCH Accommodates the most common metric size pin configura- tions including: 3.5mm, 4mm, 4.5mm, 5mm, 6mm, 7mm and 10mm
Includes: Driving shaft, driving shaft extension, expander unit, (5) split driving plugs, (2) driving collars, centering cone and molded case.
on most domestic and imported vehicles • For use with 3/8” and 1/2” drive ratchets
ATD-5405.................................... $17.69
ATD-5666.................................. $123.19
ATD-8614.................................. $111.99
LIS-18000................................. $280.59
FLYWHEEL LOCKING TOOL FOR 6.6L DURAMAX Works on 6.6L Duramax engines with Allison automatic transmissions. Saves time by locking the flywheel at the transmission
FUEL TANK LOCK RING KIT Channel design on body allows 2 interchangeable sets of legs to adjust to fit rings from 4” to 7-1/4” and keeps the drive centered
6-PC. CASTER CAMBER KIT FOR GM The kit includes 5 cam adjusting holding tools to adjust the control arm cams found on chevrolet and gmc vehicles
LIS-41620........................................................ $99.99
LIS-62970........................................................ $68.99
LIS-22100........................................................ $53.59
FAN CLUTCH WRENCHES
6-IN-1 FAN CLUTCH WRENCH • Sizes included: 22, 32, 36, 40, 48 and 50mm • Convenience of combining the six most commonly used wrench sizes onto one double-end wrench • Offset wrenches provide better hand alignment and a clearer line of sight, while improving accessibility in tight fan clutch areas
10-PC. PNEUMATIC FAN CLUTCH WRENCH SET
FAN CLUTCH WRENCH SERVICE KIT
FAN CLUTCH WRENCH SET • Removes and installs the fan clutch on many models when repairing or replacing water pump, timing chain, or the fan clutch
Set includes nine driving wrenches that fit Ford, GM, VW, BMW, Chrysler and newer International. Driving wrench sizes include: 7/8”, 32mm, 36mm, 40mm Thin, 47mm, 1-7/8”, 2”, 52mm, and 2-1/8”. Use with an air hammer
• Removes and installs the fan clutch on many models when repairing or replacing water pump, timing chain, or the fan clutch • Includes universal pully holder with pin set (5x8mm); 6, 22, 40, 47 & 50mm Fan Clutch Wrenches
• Includes universal pulley holder with pin set (5x8mm); 36mm fan
• Square drive cutouts designed for use with a breaker bar for added torque or length
LIS-43350................................. $198.49
KAS-3406....................................$42.29
KAS-3472....................................$71.79
KAS-41570................................ $163.19
SERPENTINE BELT TOOLS
15-PC. SERPENTINE BELT TOOL SET WITH LOCKING FLEX HEAD RATCHETING WRENCH
STRETCH BELT TOOL FOR FORD 3.5L & 3.7L Helps prevent damage to the belt or pulley during installation. Works on 2011 and
STRETCH BELT REMOVER / INSTALLER
Includes a locking flex-head ratcheting box wrench, a tensioning long bar, 3 adapters, seven metric 6 point sockets in sizes 13, 14, 15, 16, 17, 18 and 19 mm, & three crowfoot wrench sockets in sizes 13, 14 and 15 mm
Unique magnetic faces hold the tool in place on the pulley. Helps prevent damage to belt or pulley during removal or installation. Compact, one-piece tool can be used on the front or back side of the pulley
newer Ford 3.5L EcoBoost and 3.7L engines, as well as 2019 and newer GM 5.3L and 6.2L engine main drive belt
KDT-89000......................................................$113.89
LIS-59350........................................................ $37.99
LIS-59370.........................................................$26.39
STRETCH BELT TOOL FOR GM Double sided design allows the tool to work on both a/c and main drive pulleys when installing stretch belts on gm 5.3.L, 6.2L, and 6.6L gas engines
SERPENTINE BELT TOOL Includes 3/8” and 1/2” square drives, 13, 14, 15, 16, 18 and 19mm sockets, extension, handle and socket set with holder
11-PC. RATCHETING SERPENTINE KIT Includes 13–19mm sockets; 3/8” and 1/2” square drives, handle assembly, extension and case
LIS-59560........................................................ $18.69
LIS-59650.......................................................$126.79
LIS-59800.........................................................$88.59
Made with FlippingBook flipbook maker