Trex Select Horizontal Railing Instructions

TREX SELECT ® HORIZONTAL RAILING Installation Instructions

NOTES: » TREX SELECT RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF PRESSURE-TREATED POSTS OR POSTS INSTALLED ON OUTSIDE OF RIM JOIST IS NOT ALLOWED. » All Trex Select Railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (176.8 cm) for 6' (1.83 m) on center, and 91-5/8" (235.3 cm) for 8' (2.44 m) on center. Note that railings are designed to be slightly longer that required to allow for very slight play in post placement – trimming may be required. IT IS VERY IMPORTANT TO MEASURE FIRST. Care and Cleaning Maintaining the appearance of your Trex Select railing is important. Occasional washing is recommended. Over time your railing may show signs of weathering as a result of exposure to the elements. The frequency of cleaning will depend on the environment and exposure to various types of elements. » Clean railing with standard cleaning vinegar or mild soap and water. » For more detailed cleaning recommendations, please refer to the Trex Railing Care and Cleaning guide found on www.trex.com.

*

F

PARTS

DETERMINING BALUSTERS NEEDED

C

Per 6 ' OC Section

Per 8 ' OC Section

A

Baluster Type

**

H

Round Aluminum Baluster (Horizontal Application)

14

20

C

D

CODE APPROVED APPLICATIONS

O

6' Railing 8' Railing

*

G

E

B

Acceptable (Code approval not applicable)

< 30" height decking

Acceptable (Code approval not applicable)

I

IRC Compliant

Yes

Yes*

K

IBC Compliant

No

No

*TREX SELECT 8' ALUMINUM RAIL STIFFENER (sku SELALRAILSTIFFENER) MUST ALSO BE USED. Sold separately.

J

L

A. Select top rail B. Select bottom rail C. Brackets D. Balusters E. Adjustable foot block

NOTES: »  If installing 42" (1067 mm) railing, use longer post sleeves and measure accordingly to ensure a proper cut. DO NOT CUT TO ACTUAL 42" LENGTH WITHOUT CONFIRMING WHAT STYLE OF RAILING YOU ARE INSTALLING. »  If using 8' railings, the Trex Select 8' Aluminum Rail Stiffener (sku SELALRAILSTIFFENER) can also be used to allow for the rail to be stronger if required. »  Ensure pressure-treated posts are installed at proper heights so when post sleeves are installed , both the PT post and post sleeve are flush at top. » *See specific installation instructions for attachment of Trex post mounts or Trex Joist Mount Posts prior to installing any railing.

F. Post sleeve cap* G. Post sleeve skirt* H. P. ost sleeve – 4" x 4" (102 mm x 102 mm) or 6" x 6" (152 mm x 152 mm) post sleeve)** I. Trex Decking J. Trex Fascia K. Code-approved Wood Joist - 2 " x 8 " L. Code-approved Wood Rim Joist - 2 " x 8 " or Larger * Item not included in the Select railing kits. ** Both 4" x 4" (102 mm x 102 mm) and 6" x 6" (152 mm x 152 mm) post sleeves are designed to fit over 4x4 pressure-treated post.

Screws Supplied with RSB C1.W ood screw for attachment of RSB to wood post/composite sleeve C2.Self-drilling screw for attachment of RSB to rail

C1

C2

1

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

TSHR-0323

TREX SELECT ® HORIZONTAL RAILING Installation Instructions

TREX SELECT ® HORIZONTAL RAILING RAILING CONFIGURATIONS

Cutting post sleeves is NOT required. A. P ressure-Treated post/Trex 4x4 or 6x6 post sleeve, Trex post mount/Trex 4x4 or 6x6 post sleeve, or joist mount post/Trex 4x4 or 6x6 post sleeve (INSIDE MOUNT ONLY). B. Select top rail C. Select bottom rail D. Select balusters See page 3 for “How to Install Standard Horizontal Railing”.

Standard

B

A

D

C

Post sleeves WILL NEED TO BE CUT . A. P ressure-treated post with Trex post sleeve NOTE:

POST SLEEVES WILL NEED TO BE CUT

Cocktail

B

C

» Only for use with 4" x 4" (102 mm x 102 mm) post sleeve. » Trex post mounts or joist mount posts cannot be Select cocktail design .

A

E

B. Deck board top rail. NOTES: » Enhance cannot be used

D

» Deck boards will need to be cut to fit each rail span

C. Select top rail D. Select bottom rail E. Select balusters See page 5 for “How to Install Cocktail Horizontal Railing”.

Cutting post sleeves is NOT required. A. P ressure-Treated post/Trex 4x4 or 6x6 post sleeve, Trex post mount/Trex 4x4 or 6x6 post sleeve, or joist mount post/Trex 4x4 or 6x6 post sleeve (INSIDE MOUNT ONLY). B. 2 x 4 lateral top rail C. Select top rail D. Select bottom rail E. Select balusters See page 7 for “How to Install Traditional Horizontal Railing”.

Traditional

B

C

A

E

D

2

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

HOW TO INSTALL STANDARD HORIZONTAL RAILING TREX SELECT ®

Cutting Railings 3a.Position bottom and

3a

top rails between posts, ensuring baluster holes

are lined up and spaced evenly.

3b

3b.Also allo w for a

1-9/16" (40 mm)

minimum of 1-9/16" (40 mm) on each end of rail for bracket placement AND baluster clearance. Mark rails at intersection of rail and post.

Read all instructions BEFORE installation.

Important: Post sleeves are NO T to be cut for this design style.

Installing Pressure-Treated Posts 1.   PLEASE REFER TO LOCAL BUILDING CODE REQUIREMENTS PRIOR TO ATTACHING PRESSURE TREATED POSTS. » S elect Railing Kits are designed for posts to be installed at maximum of 6' or 8' (1.83 m or 2.44 m) ON CENTER depending on the length being used. NOTE: Smaller spans are allowed.

IMPORTANT NOTE REGARDING FOOT BLOCK INSTALLATION: » Refer to detailed instructions (Trex Select rail instructions) included with foot block prior to installation of railing section as these include other required steps for proper installation.

2a

Installing Post Sleeve Skirts and Post Sleeves 2a. If using a 1-piece skirt, slide post sleeve skirt over post and down to rest on decking surface. Slide post sleeve over post and position inside post sleeve skirt.

Attaching Foot Block to Bottom Rail and Adding Weep Holes 4a. Invert the bottom rail. Center and drill a hole using a 3/16" (5 mm) drill bit. This will be location for foot block attachment (to be installed last).

4a

2

1

2

2b

2b. If using a two-piece skirt Slide post sleeve over post and down

4b. Keeping bottom rail inverted, Use same drill bit, center and drill weep holes through bottom rail at 4 evenly spanned locations to allow for water drainage.

to rest on decking surface. Snap two piece skirt over post sleeve.

1

2

NOTE: Shims can be used to plumb post sleeves.

3

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

TREX SELECT ® HORIZONTAL RAILING Installation Instructions

HOW TO INSTALL STANDARD HORIZONTAL RAILING/ CONTINUED TREX SELECT ®

6c

6d

Attaching Brackets to Rails 5a.Position brackets on each end of TOP RAIL on the same side as baluster holes. Attach brackets using three #8-18 x 1" self-drilling screws (provided) .

5a

Top Rail

NOTE: For ease of bracket attachment place rail against stationary flat vertical surface along with bracket.

6c.Attach top rail to balusters, feeding each baluster into required slots. Start on one end and work towards the other. 6d.To help temporarily secure the railing section together, place a ratchet strap around the top and bottom rail and tighten until snug. DO NOT OVERTIGHTEN AS YOU CAN BEND THE RAILING.

5b

5b.Position brackets on

Bottom Rail

each end of BOTTOM RAIL on the OPPOSITE SIDE of the baluster holes. Attach brackets using three #8-18 x 1" self-drilling screws (provided).

Installing Railing Section to Posts

7a

7b

NOTE: For ease of bracket attachment place rail against stationary flat vertical surface along with bracket.

Assembling Railing Section

3-3/4" (95 mm)

6b

6a

7a.Using scrap material (i.e. 2 x 4s, decking boards, etc.) cut at least three support blocks at 3-3/4 " (95 mm) in height. Place one each on decking surface beside each post and one near center of span. 7b.Lift secured railing section up, and CENTER this section in between the spanned posts on pre- positioned support blocks. NOTE: To help stabilize railing section use a quick-grip clamp (or other type of clamp) and clamp the first baluster to post sleeve. DO NOT OVERTIGHTEN CLAMP.

6a.On a clean flat surface, lay bottom railing on its side. Make sure to allow enough room for installation of balusters and top rail. Place a scrap piece of 1 " (25 mm) decking board running parallel to bottom rail for support when installing balusters. 6b.Insert balusters into bottom rail slots until balusters are fully seated.

4

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

HOW TO INSTALL STANDARD HORIZONTAL RAILING/ CONTINUED TREX SELECT ®

8

Attaching Post Caps and Installing Foot Block 8. Secure post caps with silicone or PVC adhesive (apply adhesive on the inside self-centering/ corner tabs). Attach Foot Block per Foot Block instructions.

7c

NOTE: Clean up any excess adhesive before it dries.

7c.Install both bottom and top brackets on each side to post using two #9-16 x 2" wood screws (provided) . If using a 6x6 post sleeve use two #9-16 x 2 1/2" screws (not provided)

NOTE: screws go in at slight angle.

IMPORTANT NOTE: SET DRILL TO LOW SPEED AND LOW CLUTCH SETTING WHEN INSTALLING THESE SCREWS. DO NOT USE IMPACT DRIVER.

HOW TO INSTALL COCKTAIL HORIZONTAL RAILING TREX SELECT ®

Cutting Post and Post Sleeve 2. M ark and cut post and post sleeve measuring from deck surface: » 36-1/8" (918 mm) for 36" (914 mm) height. » 42-1/8" (1070 mm) for 42" (1067 mm) height.

Important: ONLY use for use with pressure-treated 4x4 post (3.5" nominal square) and 4" x 4" (102 mm x 102 mm) post sleeve. Trex Post Mounts or Joist Mount Posts cannot be used with Select Cocktail railing.

2

36-1/8" (918 mm) or 42-1/8" (1070 mm)

3.  Cutting Railings

See instructions on page 3.

4. Attaching Foot Block to Bottom Railing See instructions on page 3

1. Installing Pressure-Treated Posts, Post aSleeve Skirts and Post Sleeves See instructions on page 3.

5

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

TREX SELECT ® HORIZONTAL RAILING Installation Instructions

HOW TO INSTALL COCKTAIL HORIZONTAL RAILING/ CONTINUED TREX SELECT ®

Cutting Deck Board

8

8. S ecure deck board to

Select top rail with 3/4" screws provided approx. every 16" on center. Screws are to be installed inside of the baluster holes into the decking board. DO NOT overtighten.

NOTES: » If installing in weather below 40°F (4.5°C), leave 1/8" (3 mm) gap between deck boards. » D eck boards can overhang end of last post maximum 1/2" (13 mm).

5

NOTES: » A long drill bit will be required to fit inside the baluster holes. » If installing 8’ rail section and using Aluminum Rail Stiffener, predrilling will be required through the stiffener.

9. A ttaching Brackets to Rails See instructions on page 3 and 4.

10. Assembling Railing Sections See instructions on page 4.

5. Cut deck boards to appropriate length of railing span, remembering to include extra space on each side of the deck board to allow for attachment to the post. Decking boards must cover 1/2 of the pressure-treated post to allow this to be fastened later.

11. Installing Railing Sections to Posts See instructions on page 4.

12.  Attaching Deck Board to Posts A ttach boards on each post with Trex recommended composite screws (quantity of 2 per each board end). 13. Installing Foot Block Install foot block per detailed instructions.

12

6

6. Place inverted deck

board (top side of deck board face down) on clean, flat surface. ( DO NOT use Enhance or Escapes deck boards for top rail).

Deck Board Termination

7

Attaching Deck Board to Select Top Rail 7. Place inverted Select top rail (orient properly so baluster holes are shown top side up), on the deck board, centered in both directions to allow final attachment to post.

6

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

HOW TO INSTALL TRADITIONAL HORIZONTAL RAILING TREX SELECT ®

6

7

6. Place inverted Select top (orient properly so baluster holes are shown top side up) on 2 x 4. 7. Secure 2 x 4 to Select top rail with 3/4" screw provided approximately every 16" on center. Screws are to be installed inside of the baluster holes into the decking board. NOTES: » DO NOT overtighten. Note that a long drill bit will be required to fit inside the baluster holes. » If installing 8' rail section and using Aluminum Rail Stiffener, predrilling will be required through the stiffener.

1. Installing Pressure-Treated Posts, Post Sleeve Skirts and Post Sleeves See instructions on page 3.

2. Attaching Foot Block to Bottom Railing See instructions on page 3.

3.  Cutting Railings

See instructions on page 3.

Cutting 2 x 4

8.  Attaching Brackets to Rails See instructions on page 3 and 4.

4

9. Assembling Railing Sections See instructions on page 4.

10. Installing Railing Sections to Posts See instructions on page 4.

11.  Attaching 2x4 to Posts Pre-drill a pilot hole and toenail 2-1/2" (64 mm) composite screw (not provided) at each end of 2 x 4 into post on back side of rail (side not facing decking).

11

1

4.  Cut 2 x 4 to same length of the inverted Select top rail.

Attaching 2 x 4 to Select Top Rail 5.  Place inverted 2 x 4

(top side face down) on clean, flat surface.

5

12.  Attaching Post Caps and Installing Foot Block  Secure post caps with silicone or PVC adhesive(apply adhesive on the inside self-centering/ corner tabs). Attach Foot Block per Foot Block instructions.

7

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

TREX SELECT ® HORIZONTAL RAILING Installation Instructions

HOW TO INSTALL ON-AN-ANGLE RAILING TREX SELECT ®

NOTE: Brackets are designed to be installed up to a 45° angle.

Both 4 " x 4 " (102 mm x 102 mm) or 6 " x 6 " (152 mm x 152 mm) post sleeves work well for

4 x 4 OR 6 x 6 Post Sleeve

angles up to 45 degrees. Bottom rail brackets may need to be slightly offset to one side in order to fit properly to hold rail in place. Before attaching bracket to rail, measure and mark to ensure bottom rail remains parallel to upper rail.

4 x 4 Post Sleeve

6 x 6 Post Sleeve

8

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

TSHR-0323

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8

Made with FlippingBook - Online magazine maker