RAILING INSTALLATION
DALLAS LOS ANGELES BALTIMORE
BOLT TO SUBSTRATE 1 Use four fixing bolts to attach the stand-off post into the substrate of your choice. Take care to use
CONCRETE FLOOR WEDGE BOLT
WOOD FLOOR HEX SCREW
54-33 _ 2-1/2" ~ 3/8"
54-23 _ 2-1/2" ~ 3/8"
the correct bolt for the substrate you are using. Use a concrete floor wedge bolt for concrete (54-33) or a wood floor hex screw for wood. (54-23)
SET POSTS APART 2
LOOSEN GRUB SCREWS 3
Set the posts four to five feet apart from the center with the grub screws facing side you would like to set your railing.
Using an allen (hex) key, loosen the grub screws until they are loose and easily rotated.
SET RAILS 4
TIGHTEN GRUB SCREWS 5
Slide the rails through the holes on the sides of each grub screw. Make sure each rail is cut to the same size before this step.
Tighten the grub screws to lock the railing in place.
ADD CROSSBAR END CAP 6
Using either an adhesive or welding, affix the crossbar end caps (55-10168) to each rail. Two endcaps will be needed for each rail you want to install. Repeat until all rails are capped between both stand-off posts.
CROSSBAR END CAP **2 REQUIRED PER BAR
55-10168
CROSSBAR ROD COMPONENTS
SOLID CROSSBAR SATIN STAINLESS STEEL
CROSSBAR END CAP NEED 2 FOR EACH ROD
CROSSBAR HOLDER ROUND POSTS
CROSSBAR HOLDER SQUARE POSTS
55-10161
only accepts 55-10161 crossbar
55-10168
_ 20' ~ .47" \ 12.00 lbs
55-10165
55-10166
CHOOSE YOUR POST STYLE
STOCKED IN DALLAS ONLY
PRE-INSTALLED STAND-OFF Posts FOR CROSSBAR ROD INSTALLATIONS
WIDTH / DIAMETER
ASSEMBLY HEIGHT
POST SHAPE
WEIGHT GAUGE
MOUNT HOLES
ITEM #
55-S36FL9CB
36” Floor
9
2” 12.60 lbs 2 mm
55-S42FL11CB
42” Floor 11 2” 15.50 lbs 2 mm
55-R36FL9CB
36” Floor
9
2” 10.50 lbs 2 mm
55-R42FL11CB
42” Floor 11 2” 13.00 lbs 2 mm
55-S36FA9CB
36” Fascia 9
2” 15.40 lbs 2 mm
55-S42FA11CB
42” Fascia 11 2” 18.00 lbs 2 mm
55-R36FA9CB
36” Fascia 9
2” 12.90 lbs 2 mm
55-R42FA11CB
42” Fascia 11 2” 15.00 lbs 2 mm
GET YOUR HARDWARE & TOOLS
FOR CROSSBAR ROD INSTALLATIONS
CROSSBAR STANDOFF DRILL & TAP SET
CONCRETE FLOOR WEDGE BOLT
54-32
54-33
#25 bit #10-24 tap
_ 2-1/2 " ~ 3/8"
CROSSBAR #10 WOOD SCREW
WOOD FLOOR HEX SCREW
CROSSBAR 10-24 METAL SCREW
54-23
54-31
54-30
_ 2-1/2" ~ 3/8"
_ 1" ~ .33"
_ 2" ~ .33"
GRAB YOUR 1-5/8” OD HANDRAIL
FOR CROSSBAR ROD INSTALLATIONS
ROUND HANDRAIL SATIN FINISH
HANDRAIL POST SADDLE DRILL & TAP SET
HANDRAIL POST SADDLE SCREW REQUIRES 2 PER POST
55-10423
54-24
55-1104
#7 bit 1/4"-20 tap
_ 20' ~ 1-5/8” (42.4mm) > .080" \ 28.70 lbs
_ 1/2" ~ 1/2"
Page 1 Page 2Made with FlippingBook interactive PDF creator