PRODUCT OVERVIEW
OVERRUNNING AND GENERAL CAM CLUTCH PRODUCTS
P. 32
P. 60
P. 50
P. 38
MGUS/MGUS-R MGUS Series is suitable for applications which require low to high speed inner race. MGUS-R Series contains a built-in oil reservoir and can be used for backstopping
MZEU MZEU Series is designed for overruning applications. These units come pre-lubricated, and can be adapted with flanges and torque arms to suit a wide variety of applications. Bore Range: 0.472" to 5.906" (12 to 150 mm) Torque Range: 44 to 24,930 lbs. ft. COMPETITOR MODELS: Formsprag GFR/GFRN Stieber GFR
MZ MZ Series is designed for low speed indexing applications that require inner or outer race overrunning. These units come pre-lubricated for easy installation and long service life. Bore Range: 0.591" to 2.756" (15 to 70 mm) Torque Range: 137 to 2,242 lb.ft..
BB BB Series Cam Clutch has the bearing dimensions and
characteristics of a 62 Series type ball bearing. This design provides easy installation and is ideal for general overrunning applications Bore Range: 0.590" to 1.575" (15 to 40 mm)
applications. Bore Range:
Torque Range: 21 to 192 lb.ft.. (29 to 260 Nm) COMPETITOR MODELS: Formsprag CSK; Morse KK; Ringspann ZZ; Stieber KK
0.500" to 6.250" (12.7 to 160 mm) Torque Range:
280 to 27,290 lb.ft. (380 to 37,000 Nm) COMPETITOR MODELS: Formsprag FSO; Morse MG; Ringspann FB
(186 Nm-m to 3,040 Nm) COMPETITOR MODELS: Stieber SMZ
P. 52
P. 46
P. 44
P. 48
TFS TFS Series has two vertical keyways on the outer race to assist with positioning. Outside dimensions are the same as series 63 ball bearings. Ideal for general overrunning applications. Bore Range: 0.472" to 3.150" (12 to 80 mm) Torque Range: 13 to 2,894 lbs. ft. Competitor Models: Formsprag ASNU; Morse NFS; Ringspann FC/FDN
PBUS PBUS Series clutch is packed with a special grease for general applications. The outer race has provision for mounting gears, pulleys, and sprockets. Bore Range: 0 .375" to 1.750" (10 to 45 mm) Torque Range: 41 to 1,623 lb.ft. (56 to 2,200 Nm) COMPETITOR MODELS: Formsprag FSR; Morse PB-A; Renold SB
BUS200 BUS Series is specifically designed for shaft mounting applications that require high speed inner race overunnning or low to mid speed outer race 0.650" to 3.122" (16.5 to 79.3 mm) Torque Range: 39 to 1,025 lbs. ft. Competitor Models: Formsprag FS50; Morse B200; Renold SD overrunning. Bore Range:
OB-ON/OF & OB-SF OB-ON/OF Series is an enclosed unit housing cam clutch units and a common shaft. These units are used for high speed overrunning applications. Torque Range: 2,318 to 59,270 lbs. ft. OB-SF Series is an enclosed unit housing cam clutch units that allow for continuous high speed overrunning and engagement and high torque capacities. Torque Range: 231 to 4,337 lbs. ft.
www. ustsubaki .com
3
Made with FlippingBook Digital Proposal Creator