TAPER-LOCK ® Bushings
TAPER-LOCK Bushings — 1008 through 3030
Dimensions are in inches unless otherwise indicated.
L
M
Std. Hex Key 1¹⁄₈ 1¹⁄₈ 1³⁄₈ 1³⁄₈ 1³⁄₈ 1³⁄₈ 1³⁄₈ 1⁹⁄₁₆
Short
Std. Hex Key 1¹⁄₄ 1¹⁄₄ 1⁵⁄₈ 1⁵⁄₈ 1⁵⁄₈ 1⁵⁄₈ 1⁵⁄₈ 2 2¹⁄₄ 2¹⁄₄
Short
Bushing
F
Key
Key
Wt. Lbs.
Bore Range
No.
A
B
D
2 Required
◆
◆ ³⁄₄ ³⁄₄
1008 1108 1210 1215 1310 1610 1615 2012 2517 2525 3020 3030
— — — — — — — — — —
1.386 1.511
x x x x x x x x x x x x
.20 .25 .55 .70 .65 .70
⁷⁄₈ ⁷⁄₈ 1 1¹⁄₂
1²¹⁄₆₄ 1²⁹⁄₆₄
⁵⁄₈ ⁵⁄₈
¹⁄₂
1
¹⁄₄
¹⁄₂
¹⁄₂
1¹⁄₈
¹⁄₄
¹⁄₂
1³⁄₄ 1³⁄₄ 1⁷⁄₈ 2¹⁄₈ 2¹⁄₈ 2⁵⁄₈ 3¹⁄₄ 3¹⁄₄
¹³⁄₁₆ ¹³⁄₁₆ ¹³⁄₁₆ ¹³⁄₁₆ ¹³⁄₁₆ ¹⁵⁄₁₆
1¹⁄₁₆ 1¹⁄₁₆ 1¹⁄₁₆ 1¹⁄₁₆ 1¹⁄₁₆
¹⁄₂
1¹⁄₄
1⁷⁄₈ 1⁷⁄₈ 2 2¹⁄₄ 2¹⁄₄ 2³⁄₄ 3³⁄₈ 3³⁄₈ 4¹⁄₄ 4¹⁄₄
³⁄₈
⁵⁄₈
¹⁄₂
1¹⁄₄
³⁄₈
⁵⁄₈
1 1
¹⁄₂
1³⁄₈
³⁄₈
⁵⁄₈
¹⁄₂
1⁵⁄₈
³⁄₈
⁵⁄₈
1.00 1.40 3.20 4.30 5.80 8.00
1¹⁄₂ 1¹⁄₄ 1³⁄₄ 2¹⁄₂
¹⁄₂
1⁵⁄₈
³⁄₈
⁵⁄₈
1³⁄₈ 1⁵⁄₈ 1⁵⁄₈
¹⁄₂
2
⁷⁄₁₆
⁷⁄₈
1⁵⁄₈ 1⁵⁄₈
1 1
¹⁄₂
2¹⁄₂
¹⁄₂
1
³⁄₄
2¹⁄₂
¹⁄₂
1
¹⁵⁄₁₆ — ¹⁵⁄₁₆ —
2 3
4 4
1¹³⁄₁₆ 1¹³⁄₁₆
1³⁄₁₆ 1³⁄₁₆
2¹¹⁄₁₆ 2¹¹⁄₁₆
2¹⁄₁₆ 2¹⁄₁₆
3
⁵⁄₈
1¹⁄₄
3
⁵⁄₈
1¹⁄₄
NOTE: Metric bore sizes are available upon request and are subject to an alteration charge shown on discount multiplier sheets.
Space required to tighten bushing. Also space required to loosen screws to permit removal of hub by puller. Space required to remove bushing using jackscrews — no puller required. All bore ranges available in 1/16th inch increments. ◆ Standard hex key cut to minimum usable length.
All TAPER-LOCK Bushings are available in steel from stock.
Stainless steel bushings are available on a quoted basis. Please consult factory for pricing.
TAPER-LOCK ® is a registered trademark of Rockwell Automation.
C-66
Made with FlippingBook Digital Proposal Creator