Super-H Series
❈
Pitch
Roller
Width
Link Plate
Pin
Transverse Average Maximum Approx.
U.S. TSUBAKI
Dia.
Between Roller Link
Pitch
Tensile Allowable Weight
Strength Load
lbs./ft.
Plates
lbs.
lbs.
P
R W T
H h
D L 1
L 2
C
Chain No.
SINGLE STRAND SUPER80H SUPER100H SUPER120H SUPER140H SUPER160H SUPER200H SUPER240H DOUBLE STRAND SUPER80H-2 SUPER100H-2 SUPER120H-2 SUPER140H-2 SUPER160H-2 SUPER200H-2 SUPER240H-2 TRIPLE STRAND SUPER80H-3 SUPER100H-3 SUPER120H-3 SUPER140H-3 SUPER160H-3 SUPER200H-3 SUPER240H-3
1.000 1.250 1.500 1.750 2.000 2.500 3.000 1.000 1.250 1.500 1.750 2.000 2.500 3.000 1.000 1.250 1.500 1.750 2.000 2.500 3.000
.625 .750 .875
.625 .750
.156 .187 .219 .250 .281 .375 .500 .156 .187 .219 .250 .281 .375 .500 .156 .187 .219 .250 .281 .375 .500
.949 1.185 1.425 1.661 1.898 2.374 2.850 .949 1.185 1.425 1.661 1.898 2.374 2.850 .949 1.185 1.425 1.661 1.898 2.374 2.850
.819 1.024 1.228 1.433 1.638 2.047 2.457 .819 1.024 1.228 1.433 1.638 2.047 2.457 .819 1.024 1.228 1.433 1.638 2.047 2.457
.312 .375 .437 .500 .562 .781 .937 .312 .375 .437 .500 .562 .781 .937 .312 .375 .437 .500 .562 .781 .937
.720 .858
.823 .965
— — — — — — —
22,000 32,600 44,000 57,300 72,700 134,400 207,200 44,000 65,200 88,100 114,600 145,500 268,900 414,400 66,100 97,800 132,200 171,900 218,200 403,400 621,700
4,630 7,270 9,480
2.21 3.28 4.66 5.97 7.88
1.000 1.000 1.250 1.500 1.875
1.061 1.138 1.337 1.689 2.157 1.358 1.630 2.014 2.163 2.555 3.230 4.146 1.998 2.400 2.954 3.191 3.756 4.761 6.105
1.203 1.303 1.514 1.894 2.453 1.492 1.736 2.171 2.343 2.736 3.437 4.461 2.120 2.510 3.134 3.370 3.961 4.968 6.424
1.000 1.125 1.562 1.875
12,780 16,500 22,500 31,300 7,870 12,360 16,110 21,730 28,100 38,220 53,220 11,570 18,180 23,700 31,960 41,330 56,210 78,260
13.22 20.47
.625 .750 .875
.625 .750
1.283 1.539 1.924 2.055 2.437 3.083 3.985 1.283 1.539 1.925 2.055 2.437 3.083 3.985
4.38 6.39 9.08
1.000 1.000 1.250 1.500 1.875
1.000 1.125 1.562 1.875
11.68 15.44 25.86 40.16
.625 .750 .875
.625 .750
6.55 9.50
1.000 1.000 1.250 1.500 1.875
13.50 17.39 22.99 38.50 59.87
1.000 1.125 1.562 1.875
Note: 1. Offset links are not available.
2. Riveted type chain will be provided unless otherwise specified. Cottered type chain will be provided upon request. 3. Press-fit connecting links will be supplied. 4. Carbon steel sprockets with hardened teeth should be used with Super-H Series chain. 5. Refer to page A-42, “Chain Drive Selection.” ❈
A-40
Made with FlippingBook Digital Proposal Creator