OVERRUNNING AND GENERAL CAM CLUTCH PRODUCTS CLUTCHES & BACKSTOPS
TSUBAKI BACKSTOP CAM CLUTCH PRODUCTS CLUTCHES & BACKSTOPS
TSUBAKI INDEXING
MIUS MIUS Series is for mid-speed indexing applications up to 300 cycles a minute. Bore Range: 0.500" to 6.250" (12.7 to 160 mm) Torque Range: 280 to 27,290 lbs. ft. COMPETITOR MODELS: Formsprag HPI Morse MI Marland RMS
MGUS/MGUS-R MGUS Series is suitable for applications which require low to high speed inner race. MGUS-R Series contains a built-in oil reservoir and can be used for backstopping applications. Bore Range: 0.500" to 6.250" (12.7 to 160 mm) Torque Range: 280 to 27,290 lb. ft. (380 to 37,000 Nm)
MZEU MZEU Series is designed for overruning applications. These units come pre-lubricated, and can be adapted with flanges and torque arms to suit a wide variety of applications. Bore Range: 0.472" to 5.906" (12 to 150 mm) Torque Range: 44 to 24,930 lbs. ft. COMPETITOR MODELS: Formsprag GFR/GFRN Stieber GFR
MZ MZ Series is designed for low speed indexing applications that require inner or outer race overrunning. These units come pre-lubricated for easy installation and long service life. Bore Range: 0.591" to 2.756" (15 to 70 mm) Torque Range: 137 to 2,242 lb. ft..
BB BB Series Cam Clutch has the bearing dimensions and characteristics of a 62 Series type ball bearing. This design provides easy installation and is ideal for general overrunning applications Bore Range: 0.590" to 1.575" (15 to 40 mm) Torque Range: 21 to 192 lb. ft.. (29 to 260 Nm) COMPETITOR MODELS: Formsprag CSK; Morse KK; Ringspann ZZ; Stieber KK
CA CA line of backstops are an
BSEU BSEU Cam Clutches are a
BS & BS-F BS Series is designed for lower speed conveyor applications. The unique non-rollover cam design provides higher torque capacity, assuring full engagement. Bore Range: 0.750" to 5.315" (20 to 135 mm) Torque Range: 217 to 11,580 lbs. ft. BS-F Series is designed for simple, drop-in installations to all major competitive backstop products. Uses unique seal design for maximum life, minimal maintenance. Bore Range: 2.360" to 18.310" (60 to 465 mm) Torque Range: 4,980 to 722,000 lbs. ft.
integral part of the reducer. The unique non-rollover cam design is key and prevents damage to the gears, shafts and drive train. This is a drop-in replacement for DodgeTXT ® reducers. Bore Range: 0.738" to 1.750" (18.75 to 44.45 mm)
European variation popular on many bucket elevators in North and South America. Bore Range: 0.787" to 3.543" (20 to 90 mm) Torque Range: 159 to 3,467 lbs. ft. COMPETITOR MODELS: Formsprag RSBW
Torque Range: 45 to 901 lbs. ft. COMPETITOR MODELS: Dodge 24 Series
(186 Nm-m to 3,040 Nm) COMPETITOR MODELS: Stieber SMZ
Morse CR/BW Stieber RSBW
COMPETITOR MODELS: Formsprag FSO; Morse MG; Ringspann FB
BREU BREU Series is designed for backstop applications where bearing support and modular construction is desirable. Bore Range: 1.181" to 5.906" (30 to 150 mm) Torque Range: 447 to 25,009 lbs. ft. COMPETITOR MODELS: Formsprag RIZ; Stieber RIZ
TSS TSS Series clutch is designed for press fit installation. Outside dimensions are the same as series 62 ball bearings. Bore Range: 0.314" to 2.362" (8 mm to 60 mm) Torque Range:
BR-HT BR-HT Series is designed for backstop applications where high-speed overrunning is required. Lift off cam design assures minimal heat generation and longest life. Bore Range: 0.787" to 5.118" (20 to 320 mm) Torque Range: 77 to 269,950 lbs. ft. COMPETITOR MODELS: Formsprag RSCI; Ringspann FXM
BRUS BRUS series of high-speed external backstops utilize non-rollover and lift-off design cams. This is a drop-in replacement for Falk ® BIF backstops. Bore Range: 1.125" to 3.750" (28.58 to 95.25 mm) Torque Range: 700 to 4,420 lbs. ft. COMPETITOR MODELS: Falk BIF; Formsprag FHB; Ringspann FRXF
TFS TFS Series has two vertical keyways on the outer race to
PBUS PBUS Series clutch is packed with a special grease for general applications. The outer race has provision for mounting gears, pulleys, and sprockets. Bore Range: 0 .375" to 1.750" (10 to 45 mm) Torque Range: 41 to 1,623 lb. ft. (56 to 2,200 Nm) COMPETITOR MODELS: Formsprag FSR; Morse PB-A; Renold SB
BUS200 BUS Series is specifically designed for shaft mounting applications that require high speed inner race overrunning or low to mid speed outer race overrunning. Bore Range: 0.650" to 3.122" (16.5 to 79.3 mm) Torque Range: 39 to 1,025 lbs. ft. Competitor Models: Formsprag FS50; Morse B200; Renold SD
OB-ON/OF & OB-SF OB-ON/OF Series is an enclosed unit housing cam clutch units and a common shaft. These units are used for high speed overrunning applications. Torque Range: 2,318 to 59,270 lbs. ft. OB-SF Series is an enclosed unit housing cam clutch units that allow for continuous high speed overrunning and engagement and high torque capacities. Torque Range: 231 to 4,337 lbs. ft.
assist with positioning. Outside dimensions are the same as series 63 ball bearings. Ideal for general overrunning applications. Bore Range: 0.472" to 3.150" (12 to 80 mm) Torque Range: 13 to 2,894 lbs. ft. Competitor Models: Formsprag ASNU; Morse NFS; Ringspann FC/FDN
4 to 479 lb. ft. (6 to 649 Nm) COMPETITOR MODELS: Formsprag AS Morse NSS Ringspann FCN
For a complete listing of all Tsubaki Cam Clutches, please download the Tsubaki Cam Clutch catalog at: www.ustsubaki.com
Dodge® is a registered trademark of Baldor Electric Company Corporation. Falk® is a registered trademark of Rexnord Industries, LLC. Morse® is a registered trademark of BorgWarner Inc. Corporation Delaware. Formsprag® is a registered trademark of WARNER ELECTRIC TECHNOLOGY LLC LIMITED LIABILITY COMPANY DELAWARE. Marland® is a registered trademark of FORMSPRAG LLC LIMITED LIABILITY COMPANY DELAWARE. Renold® is a registered trademark of Renold Public Limited Company PUBLIC LIMITED COMPANY UNITED KINGDOM. Ringspann® is a registered trademark of RINGSPANN sGmBH FED REP GERMANY. Stieber® is a registered trademark of ALTRA INDUSTRIAL MOTION CORP CORPORATION DELAWARE.
223
224
Made with FlippingBook Digital Proposal Creator