TRANS-COOL Manual TransMISSION Coolers
4WD TRANSFER CASE SUPPORT BRACKET KIT (‘03-’07) TC48REAC: $132.95 4WD transfer case housings
Specify truck year and transmission when ordering.
on trucks with 48RE transmissions often crack and this is typically due to the lack of support of the heavy transfer case. This kit has been designed to solve this problem and is easy to install.
DUAL COOLERS KIT ‘05-‘18, G56 TRANSCOOL_2: $239.95 ‘94-‘05, NV4500/NV5600 TRANSCOOL_3: $239.95 ‘89-‘93, Getrag 360 TRANSCOOL_1: $239.95
A specially designed steel bracket installs in place of the lower two bolts (longer bolts supplied), and includes the common universal mount. NOTE: Must have factory skid plate installed to work.
2-Low Transfer Case Kit
SINGLE COOLER KIT ‘05-‘18, G56 TRANSCOOL_SGL_2: $126.95 ‘94-‘05, NV4500/NV5600 TRANSCOOL_SGL_3: $126.95 ‘89-‘93, Getrag 360 TRANSCOOL_SGL_1: $126.95
The TRANS-COOL is designed to transmit heat from the inner surfaces to the air-cooled outer fins which helps dissipate heat from the transmission. Each individual cooler adds an additional half a quart of trans fluid to the gearbox. Depending on the TRANS-COOL kit, it includes: aluminum cooler(s); PTO gasket(s); twelve or six PTO bolts and washers; and 1/8 NPT temperature gauge ports with plugs.
‘13-‘22, Ram 3500, ‘14-‘22, Ram 2500 ‘19-‘22, Ram 4500/5500 ‘09-‘22, Ram 1500 BD-1030705: $190.95
‘94-‘01, Ram 2500/3500 BD-1030703: $228.95
This BD kit is designed to allow the truck owner to manually disable the front wheel drive mechanism by holding the hubs free (2WD) mode with the transfer case in 4WD-Low range. With this kit installed, the front wheels will NOT be driven through the transfer case.
Check for possible clearance problems with a larger aftermarket exhaust system before ordering. You will need a minimum of 4 inches of clearance from the base of the PTO mounting surface
short shift kit ‘03-‘05, NV5600 - 6 Speed BD-1031055: $355.95 ‘98-‘02, NV5600 - 6 Speed BD-1031050: $355.95 ‘98-‘02, NV4500 - 5 Speed BD-1031056: $355.95
BD-1031055 Shown
Missed shifts are commonplace. The BD kit has eliminated that
Heavy-Duty Hydraulic Clutch Slave and Master Cylinder Assembly No bleeding of master cylinder required. *NOTE: ‘03-‘18 #HYD-X-750 not for use with G56 transmission with OEM dual mass flywheel.
problem and made it easier to shift without fear of a missed shift. The net effect of all short shift kits is that you lengthen the bottom, shorten the top, and this changed leverage makes shifting a short "click." An added benefit to the BD kit: it seems to angle the shifter to the left and back towards the driver for easier positioning.
(‘94-‘97) Non-Adj. HYD-X-HD: $367.98
(‘03-‘18) Adj. HYD-X-750: $367.98
(‘98-‘02) Adj. HYD-X-150: $367.98
If you are concerned about a front driveshaft failure on your Ram Cummins Turbo Diesel truck and want to avoid a failure turning into a catastrophe, this Front Driveshaft Loop Kit from Five Nine Fab is your answer. What can happen: A driveshaft failure on our Ram trucks typically occur at the double cardan joint on the upper end of the shaft, next to the transfer case. After the driveshaft or transfer case breaks free, the loose driveshaft is likely to come through the cab floor, and can potentially rupture nearby fuel/brake/transmission lines; even causing fire in some cases. This driveshaft loop will not prevent driveshaft failures, but it will protect from secondary damage in the event of a failure. It is still recommended to grease and inspect your driveshaft frequently. Please Note: "2013 and up models have Center Axle Disconnect (CAD), and the front driveshaft isn't 'driven' unless 4WD is engaged...We believe the driveshaft loop is still a good idea, especially if you spend a lot of time in 4 wheel drive." - from Five Nine Fab.
front driveshaft loop kits
‘94-‘02, 2500/3500, 12V & 24V FNF2GDSL: $130.00 ‘03-‘13, 2500, 5.9L & 6.7L ‘03-‘12, 3500, 5.9L & 6.7L FNF3G4GDSL: $100.00 ‘14-‘18, 2500, 6.7L ‘14-‘18, 3500, 6.7L FNF4GDSL: $100.00 ‘19-‘24, 2500/3500, 6.7L FNF5GDSL: $100.00 ‘14-‘24, 2500, 6.7L w/ Carli ‘13-‘24, 3500, 6.7L w/ Carli FNFCARLIDSL: $130.00
• Includes all required high-tensile hardware • No Drilling Required
• Laser-cut and Powdercoated • 1/4" Plate Steel Construction
FNF3G4GDSL Shown
Made in the USA
Ram Turbo Diesel Parts & Accessories #127 84
Get Ram Cummins technical information at our website: https://www.genosgarage.com/tech_info
Made with FlippingBook Ebook Creator