DNX(F) / DNH / DNHS ■ Application Examples Part Material
Automotive Components Grey Cast Iron
Part Material
Construction Machine Component / Cast Steel
Used Equipment
Machining Center (BT30)
Used Equipment
Machining Center (BT50)
Type DNXF Type Conventional Tool Body DNXF 43000R Cutter for C.I. Insert G Type Negative Insert Tool Dia. (in) 3 3 Number of Teeth 8 8 Insert Grade ACK200 K Class CVD
Type DNHS Type Conventional Tool Body DNHS 12100R General-purpose Cutter Insert H Type Negative Insert
Tool
Tool
Tool Dia. (mm)
100
100
Number of Teeth 8 (4) * 7 Insert Grade ACP200 P Class CVD
H
Cutting Speed (SFM)
656
656
Cutting Speed (SFM)
560
560
0.0025 ( v f = 16.5 IPM)
0.0025 ( v f = 16.5 IPM)
Cutting Conditions 0.003 ( v f = 11.8 IPM) Axial Depth of Cut (in) 0.12" to 0.16" 0.12" to 0.16" Cutting Width (in) 1.97 1.97 Dry/Wet Dry Dry Enables 1.5 times the efficiency of conventional tools. *( ) indicates effective no. of teeth Feed Rate per Tooth (IPTt) 0.01 ( v f = 17.7 IPM)
Feed Rate per Tooth (IPT)
Cutting Conditions
Axial Depth of Cut (in)
0.06
0.06
Cutting Width (in)
2.4
2.4
Dry/Wet
Wet
Wet
Double the tool life of conventional tools under the same conditions.
Part Material
Electrical Appliance Component Grey Cast Iron
Part Material
Housing - Grey Cast Iron
Used Equipment
Machining Center (BT50)
Used Equipment
Machining Center (BT50)
Type DNXF Type Conventional Tool Body DNXF 44000R Cutter for C.I. Insert H Type Negative Insert Tool Dia. (in) 4 4 Number of Teeth 10 10 Insert Grade ACK200 K Class CVD
Type
DNX Type Conventional Tool
Body
DNX 46000R General-purpose Cutter
Insert
G Type Positive Insert
Tool
Tool
Tool Dia. (inch)
6
6
Number of Teeth 10 Insert Grade ACK200 K Class CVD 10
Cutting Speed (SFM)
1030
1030
Cutting Speed (SFM)
790
790
0.006 ( v f = 60 IPM)
0.004 ( v f = 43.3 IPT)
0.0047 ( v f = 23.5 IPM)
0.003 ( v f = 15.6 IPM)
Feed Rate per Tooth (IPT)
Feed Rate per Tooth (IPT)
Cutting Conditions
Cutting Conditions
Axial Depth of Cut (in)
0.06
0.06
Axial Depth of Cut (in)
0.12
0.12
Cutting Width (in)
3
3
Cutting Width (in)
5.3
5.3
Dry/Wet
Wet
Wet
Dry/Wet
Wet
Wet
1.5 times longer tool life than conventional tools.
1.4 times the milling efficiency and 1.3 times the tool life of conventional tools.
■ Precautions when Using Wiper Inserts with Holes ● When assembling the wiper insert, attach it as shown in Fig. 1. When attached as shown in Fig. 2, normal machined surface roughness cannot be obtained.
● Wiper inserts are single-cornered and double-sided. ● Refer to Technical Guidance page N19 in the General Catalogue for details about wiper inserts. ● Do not use with DNHS and DNH types.
DNHS Type
DNH Type
DNX(F) Type
Fig 1
Fig 2
Correct Mounting Incorrect Mounting
Inappropriate
Inappropriate
H45
Made with FlippingBook flipbook maker