MINI Boring Tool Holder CKB
Very Small Diameter L Type Clamp-on
Fig 1
HBKL
Offset: 0
LH3
LF
(3.5)
6.5
E
H = HF (Cutting Edge Height)
Holder
Parts
Dimensions ( mm )
C
Clamp Double Screw Wrench
Overall Length
Depth of Cut
Height Width
Width Head Head
Cat. No.
Applicable Insert
Fig
H B LF CDX B2 HBKL LH3
(For Hex Socket)
CKBSR1016-16-06 CKBSR1016-16-11 CKBSR1216-16-06 CKBSR1216-16-11 CKBSR1216-16-20 CKBSR1616-16-06 CKBSR1616-16-11 CKBSR1616-16-20
10 16 125 6 26 28.5 10 KBMX L0206- ○○ R 10 16 125 11 31 28.5 10 KBMX L03,04,0511- ○○ R 1 1 12 16 150 6 26 28.5 10 KBMX L0206- ○○ R 12 16 150 11 31 28.5 10 KBMX L03,04,0511- ○○ R 1 1
D
CKBW16 WB4-8 LH020
12 16 150 20 40 28.5 10 KBMX L04,0520- ○○ R 16 16 150 6 26 34.5 16 KBMX L0206- ○○ R
1 1
R
16 16 150 11 31 34.5 16 KBMX L03,04,0511- ○○ R 1 16 16 150 20 40 34.5 16 KBMX L04,0520- ○○ R 1
S
KBMX Type (For Very Small Diameter L Holder) (
Coated Carbide)
Dimensions (Inch / mm )
Min. Bore Dia.
Cutting Edge Position
Corner Radius
Overall Length
Boring Depth
Offset
Cat. No.
DMIN WF3
E3
RE
L
CDX
Fig 1
T
KBMXL0206-05R .079" 2.0 KBMXL0206-20R KBMXL0311-05R .118" 3.0 KBMXL0311-20R KBMXL0411-05R .157" 4.0 KBMXL0411-20R KBMXL0420-05R .157" 4.0 KBMXL0420-20R KBMXL0511-05R .197" 5.0 KBMXL0511-20R KBMXL0520-05R .197" 5.0 KBMXL0520-20R
.0019" / 0.05 9.252" 23.5 .0079" / 0.20 .0019" / 0.05 1.122" 28.5 .0079" / 0.20 .0019" / 0.05 1.122" 28.5 .0079" / 0.20 .0019" / 0.05 1.476" 37.5 .0079" / 0.20 .0019" / 0.05 1.122" 28.5 .0079" / 0.20 .0019" / 0.05 1.476" 37.5 .0079" / 0.20
.0197 " 0.5 .0197 " 0.5 .0197 " 0.5 .0197 " 0.5 .0197 " 0.5 .0197 " 0.5
.0098" 0.25 .0118" 0.30 .0197" 0.50 .0197" 0.50 .0197" 0.50 .0197" 0.50
.236" 6 .433" 11 .433" 11 .787" 20 .433" 11 .787" 20
55°
DMIN Min. Bore Dia.
V
L
10°
CDX
RE
W
* Figure shows left hand insert with a right hand cutting edge
Electronic Component (Free Cutting Stainless Steel) Application Example (1)
Automotive Fuel Pump Component (SUS430) Application Example (2)
0.75”
0.75”
0.217” 5.5
Holder: CKBR1212-16 Insert: KBMXR 0420-05 (ACZ310) Cutting Speed: v c =60m/min Feed Rate: f = 0.01mm/rev Depth of Cut a p = 0.03mm Coolant: Non water soluble coolant Cutting Speed: v c =197 SFM Feed Rate: f = 0.0004 IPR Depth of Cut: a p = 0.0012” Coolant: Non water soluble coolant Holder: CKBR1212-16 Insert: KBMXR 0420-05
Holder: CKBR1616-16 Insert: KBMXR 0206-05T (ACZ150) Cutting Speed: v c =80m/min Feed Rate: f = 0.03mm/rev Depth of Cut a p = 0.05mm Coolant: Non water soluble coolant Holder: CKBR1616-16 Insert: KBMXR 0206-05T Cutting Speed: v c =262 sfm Feed Rate: f = 0.0012 IPR Depth of Cut: a p = 0.002” Coolant: Non water soluble coolant
• USA Stocked Item Worldwide Warehouse Item
E65
Made with FlippingBook flipbook maker