MOLD FINISH MASTER CBN Radius Endmills BNBR Type
Hardened Steel 45 to 55HRC
Hardened Steel 55 to 60HRC
Hardened Steel 60 to 65HRC
Pre-hardened Steel
Corner
Fig 1
Flutes
Side Milling
Face Milling
Profiling
Identification Code BNBR 2 D050 R010 - 015 4
RE ±0.005
fig 1
APMX
Series Code
Number of Teeth
Dia.
Nose Radius
Neck Length
Shank Dia.
LU
LF
Body
Dimensions ( mm )
Dia. DC
Radius RE
Cutting Edge Length APMX
Neck Length LU
Overall Length LF
Head Dia. DN
Shank Dia. DMM
L
Cat. No.
Wiper Edge Fig
BNBR2D020R005-0054 BNBR2D030R005-0054 BNBR2D040R005-0054 BNBR2D050R005-0054 BNBR2D050R005-0154 BNBR2D050R005-0254 BNBR2D050R010-0154 BNBR2D050R010-0254 BNBR2D100R005-0304 BNBR2D100R005-0504 BNBR2D100R010-0304 BNBR2D100R010-0504 BNBR2D100R020-0304 BNBR2D100R020-0504 BNBR2D100R030-0304 BNBR2D100R030-0504 BNBR2D150R010-0454 BNBR2D150R010-0754 BNBR2D150R020-0454 BNBR2D150R020-0754 BNBR2D150R030-0454 BNBR2D150R030-0754 BNBR2D200R010-0604 BNBR2D200R020-0604 BNBR2D200R030-0604 BNBR2D200R050-0604
0.2 0.3 0.4 0.5 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.5 1.5 1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0
0.05 0.05 0.05 0.05 0.05 0.05 0.10 0.10 0.05 0.05 0.10 0.10 0.20 0.20 0.30 0.30 0.10 0.10 0.20 0.20 0.30 0.30 0.10 0.20 0.30 0.50
0.1
0.5 0.5 0.5 0.5 1.5 2.5 1.5 2.5 3.0 5.0 3.0 5.0 3.0 5.0 3.0 5.0 4.5
50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50
0.17 0.27 0.37 0.47 0.47 0.47 0.47 0.47 0.97 0.97 0.97 0.97 0.97 0.97 0.97 0.97 1.47 1.47 1.47 1.47 1.47 1.47 1.97 1.97 1.97 1.97
4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
No No No No No No No No
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0.15
0.2 0.3 0.3 0.3 0.3 0.3 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 1.2 1.2 1.2 1.2 1.2 1.2 1.5 1.5 1.5 1.5
Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
7.5
4.5
7.5
4.5
7.5
6.0 6.0 6.0 6.0
Grade: BNX20
Recommended Cutting Conditions 1. Use a machine with high rigidity for stable cutting. 2. Non-water soluble cutting oil is recommended. Supply as a mist or external coolant. Take fire prevention precautions to avoid fire hazards caused by sparks igniting during machining or tool breakage. 3. Shorten overhang as much as possible. 4. Adjust cutting conditions as necessary as machine rigidity and other conditions may vary. 5. Depths of cut shown in the table of conditions are maximum depths. Adjust the actual depth of cut to the desired machined surface roughness.
a e
Part Material
STAVAX, NAK80, SKD61 (Up to 52HRC)
ELMAX, DC53, SKD11 Modified (Up to 62HRC)
YXR3, SKH (Up to 70HRC)
DC ( mm )
RE ( mm )
LU ( mm )
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
a p ( mm )
a e ( mm )
a p ( mm )
a e ( mm )
a p ( mm )
a e ( mm )
40,000 40,000 40,000 40,000 40,000 40,000 40,000 40,000 35,000 35,000 35,000 35,000 35,000 35,000 35,000 35,000 26,000 26,000 26,000 26,000 26,000 26,000 20,000 20,000 20,000 20,000
40,000 40,000 40,000 40,000 40,000 40,000 40,000 40,000 35,000 35,000 35,000 35,000 35,000 35,000 35,000 35,000 26,000 26,000 26,000 26,000 26,000 26,000 20,000 20,000 20,000 20,000
40,000 40,000 40,000 40,000 35,000 35,000 35,000 35,000 30,000 30,000 30,000 30,000 30,000 30,000 30,000 30,000 20,000 20,000 20,000 20,000 20,000 20,000 15,000 15,000 15,000 15,000
0.2 0.05 0.5 0.3 0.05 0.5 0.4 0.05 0.5
400 0.005 0.03 500 0.010 0.05 600 0.015 0.1
400 0.005 0.03 500 0.010 0.05 600 0.015 0.1
250 0.005 0.02 300 0.005 0.03 400 0.01 0.05
0.05 0.5
0.02 0.15 0.02 0.1
0.02 0.15 0.02 0.1
0.1
0.05
1.5
0.1
0.5
600
600
400 0.01
0.05
0.05
2.5
0.01 0.05
0.01 0.05
0.1
0.05
0.1 0.2 0.3 0.1 0.2 0.3 0.1 0.2 0.3 0.1 0.2 0.3 0.1 0.2 0.3 0.5
3.0
0.03 0.3
800 0.03 0.2
600 0.01 0.1
1.0
800
0.05
5.0
0.02 0.2
800 0.02 0.1
600 0.01 0.1
4.5
0.03 0.5
800 0.03 0.3
600 0.02 0.3
1.5
800
7.5
0.03 0.5
800 0.03 0.3
600 0.02 0.3
2.0
6.0
800 0.03 0.7
800 0.03 0.7
600 0.03 0.7
L129
Made with FlippingBook flipbook maker