GSX MILL Endmills (2 Flutes) GSX 200C-4D I nch Type
Ti Alloy / Heat Resistant Alloy
Hardened Steel 45 to 55HRC
Hardened Steel 55 to 60HRC
Stainless Steel
General Steel
Carbon Steel
Alloy Steel
Pre-hardened Steel
Tempered Steel/Die Steel
Cast Iron
GSX I nch P roducts are made to order
Corner
Flutes
Coat
Side Milling
Groove Finishing
Face Milling
Spot Facing
Helix Angle
Fig 1
Fig 2
APMX
APMX
15°
LF
LU
LF
DC
Tolerance
I
D ≤ 3.0
0 -0.015 0 -0.020 0 -0.030
3.0 < D ≤ 12
12.0 < D
GSX Inch - Made to Order
Body
Endmill Identification (GSXMILL Series Only)
Dimensions (inch)
Series Code GSX 2 04 C - 4D
Dia. DC
Cutting Edge Length APMX
Neck Length LU
Overall Length LF
Shank Dia. DMM
Cat. No.
Fig
GSX204C-4D GSX206C-4D GSX208C-4D GSX210C-4D GSX212C-4D GSX214C-4D GSX216C-4D GSX218C-4D GSX220C-4D GSX224C-4D GSX228C-4D GSX232C-4D GSX236C-4D GSX240C-4D GSX244C-4D GSX248C-4D GSX256C-4D GSX264C-4D
0.0625 0.2500 0.0938 0.3750 0.1250 0.5000 0.1563 0.6250 0.1875 0.7500 0.2188 0.8752 0.2500 1.0000 0.2813 1.1252 0.3125 1.2500 0.3750 1.5000 0.4375 1.7500 0.5000 2.0000 0.5625 2.2500 0.6250 2.5000 0.6875 2.7500 0.7500 3.0000 0.8750 3.5000 1.0000 4.0000
0.2894 0.4144
1.500 2.000 2.000 2.000 2.500 2.500 2.500 3.000 3.000 3.500 4.000 4.000 5.000 5.000 5.000 5.500 5.500 6.000
0.1250 1 0.1250 1 0.1250 2 0.1875 1 0.1875 2 0.2500 1 0.2500 2 0.3125 1 0.3125 2 0.3750 2 0.4375 2 0.5000 2 0.5625 2 0.6250 2 0.6875 2 0.7500 2 0.8750 2 1.0000 2
Cutting Edge
Cutting Edge Length
Diameter in 64ths
Number of Flutes
(4/64 = 0.0625")
-
C: Gash Land
0.6841
-
0.954
-
1.204
- - - - - - - - - -
Grade: ACF20
Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders. 2. Use air blow when dry machining.
3. Use wet machining for stainless steel, heat-resistant alloy, and titanium alloy applications. 4. In some cases, chattering may occur in early stages of milling but will cease after 2m of cutting. 5. If chatter is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut. 6. This series is not recommended for groove milling. 7. If the machine cannot achieve the recommended spindle speed, please use the maximum spindle speed available.
a e
DC
Side Milling
Carbon Steel SC (150 to 250HB)
Alloy Steel SCM (25 to 35HRC)
Tempered Steel, Hardened Steel NAK , HPM (35 to 45HRC)
Work Material Cutting Conditions
Steel for Structure SS
Cast Iron FC
Hardened Steel (45 to 55HRC)
Stainless Steel SUS304,SUS316
Heat-Resistant Alloy Titanium Alloy
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
DC (inch)
130 9,000 130 9,000 130 7,000 95 6,500 50 4,500 30 5,400 40 4,500 25 180 4,500 180 4,500 180 3,500 120 3,200 70 2,300 40 2,700 50 2,300 35 240 2,250 240 2,250 240 1,750 160 1,600 95 1,200 60 1,350 65 1,200 40
< 0.039 9,000 < 0.078 4,500 < 0.156 2,250 < 0.236 1,500 < 0.315 1,100 < 0.393 900 < 0.472 750 < 0.630 550 < 0.787 450 < 1.000 360
300 1,500 300 1,500 300 1,150 170 1,050 110
800 70 600 70 460 70 400 70 300 55
900 70 660 70 540 70 450 70 330 60
800 50 600 50 460 50 400 50 300 45
260 1,100 260 1,100 260
850 170 700 160 580 160 440 140 350 120
800 110 650 110 520 110 400 95
250 240 200 180 140
900 250 750 240 550 200 450 180 360 140
900 250 750 240 550 200 450 180 360 140
320 250
85 65
240 190
45 35
270 210
50 40
240 192
40 30
280
95
3.5DC
3.0DC
a p a e
Standard Depth of Cut
0.08DC
0.04DC
I 31
Made with FlippingBook flipbook maker