Grooving Tools GNDI
GND for Internal (ID) Grooving
Internal
Internal Grooving GNDI
Min. Bore Diameter (DMIN)
Fig 1
DCON
H
CW
LHD
LF
F
Holder
Parts Dimensions (inch / mm )
Figure shows right hand (R) tool.
Min. Bore Diameter
Cutting Edge Distance
Max. Groove Depth
Screw Wrench
Stock
Overall Length
Seat Size
Diameter Height Head
Applicable Insert
Cat. No.
Fig
R L
N m
DCON H LHD LF WF DMIN CW CDX
GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□ GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□ GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□
GNDI R/L 162T-25 GNDI R/L 163T-25 GNDI R/L 164T-25 GNDI R/L 165T-25 GNDI R/L 166T-25 GNDI R/L 202T-40 GNDI R/L 203T-40 GNDI R/L 204T-40 GNDI R/L 205T-40 GNDI R/L 206T-40 GNDI R/L 243T-43 GNDI R/L 244T-43 GNDI R/L 245T-43 GNDI R/L 246T-43
● ● 1.000 .906 1.575 8.000 .623 1.250 2 .250 ● ● 1.000 .906 1.575 8.000 .623 1.250 3 .250 ● ● 1.000 .906 1.575 8.000 .748 1.250 4 .250 ● ● 1.000 .906 1.575 8.000 .748 1.250 5 .250 ● ● 1.000 .906 1.575 8.000 .748 1.250 6 .250 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 2 .400 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 3 .400 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 4 .400 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 5 .400 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 6 .400 ● ● 1.500 1.421 2.362 12.000 1.142 2.000 3 .430 ● ● 1.500 1.421 2.362 12.000 1.142 2.000 4 .430 ● ● 1.500 1.421 2.362 12.000 1.142 2.000 5 .430 ● ● 1.500 1.421 2.362 12.000 1.142 2.000 6 .430
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
BH0516 5.0 LH030
BH0616 6.0 LH040
GNDI R/L 2532-T206 GNDI R/L 2532-T306 GNDI R/L 2532-T406 GNDI R/L 2532-T506 GNDI R/L 3240-T210 GNDI R/L 3240-T310 GNDI R/L 3240-T410 GNDI R/L 3240-T510 GNDI R/L 4050-T311 GNDI R/L 4050-T411 GNDI R/L 4050-T511 GNDI R/L 4050-T611
25 23 40 200 16 25 23 40 200 16 25 23 40 200 19 25 23 40 200 19 32 30 50 250 26 32 30 50 250 26 32 30 50 250 26 32 30 50 250 26 40 38 60 300 31 40 38 60 300 31 40 38 60 300 31 40 38 60 300 31
32 32 32 32 40 40 40 40 50 50 50 50
6 6 6 6
2 3 4 5 2 3 4 5 3 4 5 6
BH0516 5.0 LH030
10 10 10 10 11 11 11 11
BH0616 6.0 LH040
BH0616 6.0 LH040
1 Combine the insert with a holder such that the Seat Sze matches. Refer to page F21-F22 for applicable inserts. Not usable with GNDIS inserts.
: Worldwide Warehouse Item ●: USA Stocked Item
F 14 & F15
Recommended Cutting Conditions
N m Recommended Tightening Torque (N·m)
F37
Made with FlippingBook flipbook maker