Super MultiDrills WGS Series (External Coolant Supply)
Carbon Steel/ Alloy Steel up to 0.28%
Carbon Steel/ Alloy Steel from 0.29%
Hardened Steel up to 45HRC
Stainless Steel
Tempered Steel
Ductile Cast Iron
Cast Iron
Coating
*Refer to N74 for the tolerance of h6 and h8
Fig 1
PL
LCF
OAL
J
This product is a made-to-order item. Please specify the hole diameter (including tolerance) when ordering.
Body
Dimensions ( mm )
Dia. DC
Flute Length LCF
Overall Length OAL
Tip PL
Shank Dia. DCON
Cat. No.
Fig
MDW 0680 to 0700WGS2 MDW 0710 to 0750WGS2 MDW 0760 to 0800WGS2 MDW 0810 to 0850WGS2 MDW 0860 to 0900WGS2 MDW 0910 to 0950WGS2 MDW 0960 to 1000WGS2 MDW 1010 to 1050WGS2 MDW 1060 to 1100WGS2 MDW 1110 to 1150WGS2 MDW 1160 to 1200WGS2 MDW 1210 to 1250WGS2 MDW 1260 to 1300WGS2 MDW 1310 to 1350WGS2 MDW 1360 to 1400WGS2 MDW 1410 to 1450WGS2 MDW 1460 to 1500WGS2 MDW 1510 to 1550WGS2 MDW 1560 to 1600WGS2
6.8 to 7.0 7.1 to 7.5 7.6 to 8.0 8.1 to 8.5 8.6 to 9.0 9.1 to 9.5
34 35 38 38 40 40 43 43 47 47 49 50 52 53 55 55 56 56 58
74
1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3
7.0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
80
8.0
84
9.0
89
10.0
9.6 to 10.0 10.1 to 10.5 10.6 to 11.0 11.1 to 11.5 11.6 to 12.0 12.1 to 12.5 12.6 to 13.0 13.1 to 13.5 13.6 to 14.0 14.1 to 14.5 14.6 to 15.0 15.1 to 15.5 15.6 to 16.0
95
11.0
102
12.0
103
13.0
108
14.0
111
15.0
115
16.0
Grade: ACX70
Recommended Cutting Conditions
( v c : Cutting Speed ( m/min ), f : Feed Rate ( mm/rev ))
Dia. DC (mm)
Cutting Conditions
Mild Steel/General Steel (up to 300HB)
Stainless Steel (up to 200HB)
Gray Cast Iron FC250
Ductile Cast Iron FCD450
50 - 130
15 - 60
50 - 80
50 - 70
v c
ø10.0
0.20 - 0.35
0.10 - 0.20
0.20 - 0.35
0.20 - 0.35
f
60 - 140
20 - 60
60 - 100
50 - 80
v c
ø16.0
0.25 - 0.35
0.10 - 0.20
0.25 - 0.35
0.25 - 0.35
f
Min. - Max.
* The recommended cutting conditions are also affected by factors such as machine rigidity and the workpiece clamping. Please adjust the cutting conditions according to your work environment. * If work hardening occurs during drilling, it is recommended to use a lower speed than the recommended cutting conditions.
J59
Made with FlippingBook flipbook maker