Replaceable Tip Drills SMD Series
SMDH_1.5D = 1.5x Diameter
SMDH_M, 3D, 3DF = 3x Diameter
SMDH_L, 5D, 5DF = 5x Diameter SMDH_D, 8D, 8DF = 8x Diameter
J
SMDH_12D = 12x Diameter
See page J99 for SMDT-NAL recommendations for Non-Ferrous Materials See page J113 for SMDT-MFS recommendations for 1.5XD
■ Recommended Cutting Conditions
Mild Steel
General Steel Pre-hardened Steel Stainless Steels*
Gray Cast Iron
Ductile Cast Iron
Titanium Inconel
Material
HRC45
(up to 200HB)
<HB250 HB250-320
MEL
MTL-C / MEL MTL-C / MEL MEL
MEL
MTL
MTL
MTL
SMD Tip
Drill Dia. (Inch) Speeds/ Feeds Min - Max Min - Max
Min - Max 130-260
Min - Max
Min - Max Min - Max Min - Max Min - Max
~ .4688" 100 - 265 260 - 430 230 - 330 65 - 130 35 - 100 f (IPR) 0.006 - 0.0120.006 - 0.012 0.006 - 0.008 0.004 - 0.008 0.008 - 0.0120.006 - 0.0120.004 - 0.0080.004 - 0.008 ~ .8440" Vc (SFM) 260 - 400 230 - 400 160-300 100 - 300 260 - 430 230 - 330 85 - 150 50 - 115 f (IPR) 0.006 - 0.0140.008 - 0.014 0.006 - 0.010 0.004 - 0.010 0.008 - 0.0140.006 - 0.0140.004 - 0.0080.004 - 0.009 ~ 1.250" Vc (SFM) 260 - 430 230 - 400 160-300 100 - 300 300 - 460 260 - 360 85 - 150 50 - 115 f (IPR) 0.008 - 0.0160.008 - 0.014 0.006 - 0.010 0.004 - 0.010 0.008 - 0.0180.008 - 0.0150.004 - 0.0080.006 - 0.010 Vc (SFM) 260 - 400 230 - 400
* For difficult to machine stainless steels (316, 302, 304, 17-4ph, etc.) adjust speeds & feeds accordingly.
■ Recommended Speeds and Feeds - 12XD
Soft Steel
General Steel Hardened Steel Stainless Steel Gray Cast Iron Ductile Cast Iron Aluminum Alloy
Material
Drill Dia. (Inch)Speeds/ Feeds Min - Max
Min - Max 160 - 260
Min - Max 100 - 230
Min - Max
Min - Max
Min - Max 130 - 230
Min - Max 590 - 790
130 - 200 130 -260
160 - 260
Vc (SFM)
~0.6299"
.0039 - .0079 .0039 - .0079 .0078 - .012 .0078 - .012 .014 - .022
.0059 - .014 .0059 - .014
f (IPR)
100 - 230
130 - 230 160 - 300
130 - 260
590 - 790
160 - 260
Vc (SFM)
160 - 260
~0.7874"
.0039 - .0098 .0039 - .0098 .0079 - .014 .0079 - .014 .014 - .024
.0059 - .014 .0059 - .014
f (IPR)
100 - 230
130 - 300 160 - 300
130 - 300
590 - 790
160 - 260
160 - 260
Vc (SFM)
~1.000"
.0039 - .0098 .0039 - .0098 .0079 - .016 .0098 - .014 .014 - .024
.0078 - .014 .0078 - .014
f (IPR)
■ Recommended Tightening Torque
■ Cleaning instructions
Recommended Tightening Torque
Drill Head Size (in/ mm )
Screw
(in/lbs.)
N m
.4688 - .6102 12.00 - 15.50 .6103 - .7283 15.51 - 18.50 .7284 - .8464 18.51 - 21.50 .8465 - .9763 21.51 - 24.80 .9764 - 1.0944 24.81 - 27.80 1.0945 - 1.3189 27.81 - 33.50
BXD02208IP 6.6 to 8.8 0.75 to 1.00
BXD02509IP 8.2 to 11.0 0.93 to 1.24
BXD03011IP 16.3 to 21.6 1.83 to 2.44
1) Air Pressure Remove the used head and any debris from the serrated parts of the holder with an air nozzle. ■ Attaching instructions
2) Brushing Use a wire or nylon brush to remove debris left behind by air nozzle.
BXD03512IP 24.2 to 32.9 2.79 to 3.72
BXD04014IP 36.6 to 48.8 4.14 to 5.12
BXD04515IP 44.0 to 58.7 4.98 to 6.64
Caution! 1) Please wear safety gloves and glasses. 2) Please remove SMD from any adapator when replacing SMDT Tip. 3) Serrations may contain some debris. Placing a tip without removing any foreign particles may cause loose screws and possibly lead to tip and body breakage.
1) U se caution when tightening the head screws. 2) H old wrench parallel to SMD body when tightening. Forcing out wrench may cause screw hole breakage. 3) Tighten both screws to recommend torque settings in Tightening Torque chart (right).
J97
Made with FlippingBook flipbook maker