S9074-AQ-GIB-010/248 Rev 1
LIST OF ILLUSTRATIONS
Figure
Title
Page
Figure 7-1. Positions of Welding................................................................................................................................7-69 Figure 7-2. Typical Welding Procedure Qualification Test Plate and Recommended Locations for Removal of Test Specimens ...........................................................................................................................................................7-71 Figure 7-3. Typical Welding Procedure Qualification Pipe Test Assembly ..............................................................7-72 Figure 7-4. Test Assembly for Procedure Qualification for Cladding for Corrosion-Resistance (Also, See Figure 7-5 for Cylindrical Materials) ...................................................................................................................................7-73 Figure 7-5. Test Assembly for Procedure Qualification of Hardfacing and Cladding for Circumferential Welding of Cylindrical Materials (for Propulsion Shafting, see MIL-STD-2191)................................................................7-77 Figure 7-6. Procedure Qualification Test Plate for Hardfacing (Also See Figure 7-5 for Cylindrical Materials) .....7-79 Figure 7-7. Typical Location of Test Specimens from Dissimilar Metal Welded Test Plate.....................................7-81 Figure 7-8. Procedure Qualification Test Assembly for Fillet Welding Bare Surfaces .............................................7-82 Figure 7-9. Procedure Qualification Test Assembly for Fillet Welding Over Primer-Coated Surfaces ....................7-83 Figure 7-10. Stud Testing Apparatus..........................................................................................................................7-84 Figure 7-11. Sample for Reporting Welding Procedure Qualification Data ..............................................................7-85 Figure 7-12. Performance Qualification Test Nos. 2A and 2B for Fuel Gas Welding (Plate) ...................................7-87 Figure 7-13. Performance Qualification Test No. 3B for Fuel Gas Welding (Pipe) ..................................................7-88 Figure 7-14. Performance Qualification Test No. 1 for Arc Welding ........................................................................7-89 Figure 7-15. Performance Qualification Tests Nos. 3 and 4 for Arc Welding (Pipe) ................................................7-90 Figure 7-16. Performance Qualification Test No. 8 for Tack and Fillet Welders ......................................................7-91 Figure 7-17. Performance Qualification Test No. 9 for Weld Cladding and Hardfacing Plate..................................7-92 Figure 7-17A. Performance Qualification Test No. 9 for Hardfacing and Cladding for Circumferential Welding of Cylindrical Materials (for Propulsion Shafting, see MIL-STD-2191)................................................................7-93 Figure 7-18. Sample Performance Qualification Record ...........................................................................................7-95 Figure 7-19. Reduced Section Tension Specimen (Plate) for Brazed Lap-Type Joints .............................................7-96 Figure 7-20. Lap Joint Peel Specimen ........................................................................................................................7-96 Figure 7-21. Typical Layout and Construction for Restricted Accessibility Qualification Test Assembly Positions7-97 Figure 7-22. Performance Qualification Tests Nos. 5 and 6 for Arc Welding (Pipe) ................................................7-98 Figure 7-23. Brazing Positions ...................................................................................................................................7-99 Figure 7-24. Heat Affected Zone (HAZ) and Base Material Charpy V-Notch (CVN) Specimens..........................7-100 Figure 7-25. Mockup and Orientation of Assembly for Performance Qualification for Manual Welding of Tube-to- Header Seal Weld Joints ...................................................................................................................................7-101 Figure 7-26. Performance Qualification Test No. 10, Plasma Arc Welding – Keyhole Technique ......................... 7-102 Figure A-1. Schematic Illustrating the Effective Processing Size Defined by Ratio of (p/t) ....................................A-20 Figure A-2. Schematic of Test No. 1 for FSW Procedure and FSP Procedure Qualification Test Assembly ..........A-21 Figure A-3. Schematic of Test No. 2 for Level II FS Procedure Qualification Test Assembly ................................A-22 Figure A-4. Macro-Etch Specimen............................................................................................................................ A-23 Figure A-5. Schematic Showing the Protocol for Referencing Lateral FS Tool Offset in Welding Procedures ......A-24 Figure A-6. Schematic of Test No. 3 for Performance Qualification........................................................................A-25 Figure A-7. Definitions of Key Variables for Tilted Axis FS ...................................................................................A-26
xv
Made with FlippingBook - Share PDF online