2915P Speedtiller Powerflex 15M Operator Safety Manual

2915P SPEEDTILLER POWERFLEX OPERATOR & SAFETY MANUAL

74 Young Rd | PO Box 340, Cowra, NSW 2794 | AUS

© K-Line Ag 2023

2915P Op & safety manual.indb 1

6/02/2023 9:31:06 AM

Would you like a copy of this manual emailed to you? Send your request to marketing@k-line.net.au or scan here:

2915P Op & safety manual.indb 2

6/02/2023 9:31:06 AM

OP & SAFETY MANUAL

Table of Contents

CUSTOMER LETTER LEGAL DISCLAIMER ������������������������������������������������������������������������������������������������������������������������������������������������������1.1 INTRODUCTION After Delivery ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������1.1 Genuine Parts �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������1.1 Identifying The Machine For Requesting Spare Parts ���������������������������������������������������������������������������������������������������������������������������1.1 SPECIFICATIONS ����������������������������������������������������������������������������������������������������������������������������������������������������������1.2 GENERAL INFORMATION Tractor Requirements ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������2.1 Definitions Used In This Manual ������������������������������������������������������������������������������������������������������������������������������������������������������������������2.1 Disc Arm Identification ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������2.1 Bolt Tension ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������2.1 SAFETY INFORMATION R isk M anagement ��������������������������������������������������������������������������������������������������������������������������������������������������������������������� 3.1 Identifying Hazards ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.1 Risk Assessment ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.1 Risk Control ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.1 Monitor and Review Control Measures ������������������������������������������������������������������������������������������������������������������������������������������������������3.1 Risk Assessment Matrix �����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.2 Risk Assessment Table �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.3 I mportant S afety N otice (M ust R ead ) ��������������������������������������������������������������������������������������������������������������������������������3.4 Your Safety & The Safety Of Others Is Important �������������������������������������������������������������������������������������������������������������������������������3.5 Safety Alert Symbol �����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.5 Signal Words �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.5 S afety D ecals ������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 3.6 Safety Decal Placement ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.6 Safety Decal Part Numbers ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.7 Decals ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.8 Logo Stickers ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.11 Safety Sign Care �����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.12 O perational S afety ��������������������������������������������������������������������������������������������������������������������������������������������������������������� 3.13 Tyre Safety & Pressures ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.13 Power Lines �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.14

TABLE OF CONTENTS CONTINUED ONTO NEXT PAGE....

2915P Op & safety manual.indb 4

6/02/2023 9:31:06 AM

H ydraulic O peration & S afety ������������������������������������������������������������������������������������������������������������������������������������������� 3.15 Hydraulic System Failure �����������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.15 Hydraulic Operation ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.16 Hydraulic Hose Hook Up �����������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.16 Priming Hydraulic System ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.16 Hydraulic Colour Codes �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.17 O perating I nstructions �������������������������������������������������������������������������������������������������������������������������������������������������������3.18 Hooking / Unhooking To Tractor ���������������������������������������������������������������������������������������������������������������������������������������������������������������3.18 Electrical Connection Hook Up �������������������������������������������������������������������������������������������������������������������������������������������������������������������3.18 Transporting / Roading ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3.19 Folding / Unfolding Machine ����������������������������������������������������������������������������������������������������������������������������������������������������������������������3.20 FIELD OPERATION Speed Range ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.1 S peedtiller S tart U p T ips ������������������������������������������������������������������������������������������������������������������������������������������������������ 4.2 Tracking Adjustments ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.3 Front Disc Gang Lateral Positioning Standard Factory Setting ����������������������������������������������������������������������������������������������������4.4 Lateral Front Disc Gang Positioning �����������������������������������������������������������������������������������������������������������������������������������������������������������4.5 Adjustment Procedure ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.6 Side Coulter Adjustment ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.7 Adjustment For Excessive Trash Conditions �������������������������������������������������������������������������������������������������������������������������������������������4.7 Extension Deflector Adjustment �����������������������������������������������������������������������������������������������������������������������������������������������������������������4.7 U seful hints ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 4.8 Blocking In Excessive Trash ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.8 Clogging In Wet Soils ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.8 Ram Stop Combinations ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.8 Machine Settings ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4.9 MAINTENANCE Maintenance & Safety ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������5.1 After Delivery Check List ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������5.2 Daily Maintenance Check For Optimum Performance �����������������������������������������������������������������������������������������������������������������������5.3 B olt T orque T ables �������������������������������������������������������������������������������������������������������������������������������������������������������������� 5.4 Metric Bolt Torque Table ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������5.4 Imperial Bolt Torque Table ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������5.5 Torque Tightening Sequence. �����������������������������������������������������������������������������������������������������������������������������������������������������������������������5.6 Wheel Bearings ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������5.7 Lubrication Of Purgable Heavy Duty Rear Roller Bearings �������������������������������������������������������������������������������������������������������������5.7 EXPLODED VIEWS Speedtiller Jump Arm Assembly �����������������������������������������������������������������������������������������������������������������������������������������������������������������6.2 Disc Arm Bearing �����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������6.3 Side Coulter ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������6.4 Standard (50mm Pin) Roller Bearing �������������������������������������������������������������������������������������������������������������������������������������������������������6.5 60mm Roller Bearing Shaft �������������������������������������������������������������������������������������������������������������������������������������������������������������������������6.6 Peer Roller Bearing �������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������6.7 Adjustable Extension Deflector ������������������������������������������������������������������������������������������������������������������������������������������������������������������6.8 Heavy Duty Roller Bearing ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������6.9 Heavy Duty Roller Bearing Fitting Instructions ������������������������������������������������������������������������������������������������������������������������������������6.10 H ydraulic C ylinder L ayout ��������������������������������������������������������������������������������������������������������������������������������������������������6.11 M agna -L ite W iring H arness S chematic ����������������������������������������������������������������������������������������������������������������������������� 6.12 TESTIMONIAL PERMISSION FORM LIST OF IMAGES

2915P Op & safety manual.indb 5

6/02/2023 9:31:06 AM

Dear Customer Thank you for purchasing a 2915P Speedtiller Powerflex.

We would like to assure you that you have made a good choice, and will be able to rely on this high quality piece of equipment. We ask you to follow the user’s instructions closely as this will ensure that you experience the benefits of using the machine without experiencing the unnecessary down time caused by misuse. When you receive the machine, make sure that it has not been damaged during transportation and that no parts are missing. Contact your dealer immediately if any parts are missing. Ensure that all components are correctly adjusted. Please read, fill, sign and submit the Warranty Registration Document (including Safety Acknowledgement) that was provided with your Product. Upon submission of the Warranty Registration Document, your Dealer will provide you with a copy, which should be kept in a safe place for easy access in the future. Before operating, PLEASE TAKE THE TIME TO LEARN the process of operation. Do not take the unit for granted; ease into becoming familiar with your new equipment. The operator should be a responsible adult familiar with farm machinery and trained for this purpose. Do NOT allow persons to operate or assemble the unit until they have read this manual and understand how to use this machine and observe the safety precautions. Never exceed the limits of this machine. If its ability to do a job, or to do so safely is in question - DO NOT TRY IT. DO NOT attempt to operate this equipment under the influence of drugs or alcohol. Remember - Your best assurance against accidents is a careful and responsible operator. If you have any questions not answered in this manual or require additional copies or the manual is damaged, please contact your dealer or be free to phone us on our free call number:

AUS - 1800 194 131

The team here at K-Line Agriculture trust you enjoy a good season and prove the benefits of owning and operating a quality machine that is built to perform. Signed:

Glenn Soper General Manager - Seeding & Tillage CNH Industrial

2915P Op & safety manual.indb 6

6/02/2023 9:31:07 AM

THIS PAGE IS LEFT INTENTIONALLY BLANK

2915P Op & safety manual.indb 7

6/02/2023 9:31:07 AM

LEGAL DISCLAIMER LAST UPDATED: 06/02/23

The information contained in the K-Line Industries Pty Ltd (also trading as “K-Line Ag” and “K-Line Agriculture”) manual is for general information purposes only. K-Line Industries Pty Ltd assumes no responsibility for errors or omissions in the contents of the book. In no event shall K-Line Industries Pty Ltd be liable for any special, direct, indirect, consequential, or incidental damages or any damages whatsoever, whether in an action of contract, negligence with the use of the Service or the contents of the Service. K-Line Industries Pty Ltd reserves the right to make additions, deletions, or modification to the contents of this manual at any time without prior notice. AFTER DELIVERY When you receive the machine make sure that it has not been damaged during transportation and that no parts are missing. Only by giving us immediate advice can the necessary replacement parts be obtained. Ensure that all components are correctly adjusted. GENUINE PARTS K-Line spare parts and accessories have been specifically designed and developed for the machines produced. We would call your attention to the fact that non-genuine parts and accessories are not recommended by K-Line. The use of such replacement parts frees K-Line from all liability and makes the warranty void. The installation and/or use of non-genuine parts may, because of technical characteristics of construction, modify or influence the performance of the machine negatively. IDENTIFYING THE MACHINE FOR REQUESTING SPARE PARTS The machine is identified by the serial number on the metal plate on the machine. When requesting spare parts or maintenance service, please indicate the model and number of your equipment to ensure prompt and efficient attention.

1.1 1.1

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 1

6/02/2023 9:31:07 AM

Specifications

SPECIFICATIONS

MODEL SPECIFICATIONS OPERATING WIDTH APPROX. NUMBER OF DISCS DISC CUT SPACING ADJUSTABLE DISC POSITIONING STANDARD DISC SIZE

2915P

15.5M (50.8FT)

124

125MM (5”)

YES

610MM X 6MM (24” X 1/4”)

SPEEDTILLER WEIGHT WITH STANDARD ROLLERS

22500KG (49613LB)

TRANSPORT WIDTH TRANSPORT HEIGHT

5.8M

4M

TRACTOR POWER RANGE

550-700HP (410-530KW)

TRACTOR HYDRAULIC REQUIREMENTS

5 X DOUBLE SPOOL (WITH OPTIONAL HYDRAULIC ROLLER ADJUSTMENT)

HYDRAULIC REMOTES

HYDRAULIC PRESSURE

2800 PSI (190 BAR) (19000KPA) REQUIRED MAXIMUM FLOW 10GPM (38 LITRES/MIN) FLOW ADJUSTABLE

HYDRAULIC FLOW CAPACITY

HITCH TYPE

CAT 5 TRAILING HITCH

Figure : 1.1 Model Specifications

TYRE SPECIFICATIONS

TYRE PRESSURE.

WHEEL NUT TENSION

50PSI / 344KPA 75PSI / 517KPA

200 LB-FT (270NM)

CENTRE

WING 200FT LBS /270NM When optional flotation tires are fitted use tire pressures stated on the tire. If no pressure stated use 50/55 PSI.

Figure : 1.2 Tyre Specifications.

1.2

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 2

6/02/2023 9:31:07 AM

General Information

GENERAL INFORMATION TRACTOR REQUIREMENTS 10-14 Horsepower x width of machine in feet. 25-35 Kilowatt x meter width of machine in meters. Tractor weight must be the same as or greater than the towed unit. Hydraulic valves: With optional hydraulic roller adjustment 5 x double spool Hydraulic operating pressure: 2800 PSI

DEFINITIONS USED IN THIS MANUAL

DISC ARM IDENTIFICATION VIEW FROM REAR OF MACHINE FRONT ARM REAR ARM Figure : 2.1 Tractor Orientation.

BOLT TENSION Top plate bolt tension Min:75ft-lb / 100N-m Max:100ft-lb / 135N-m Disc bolt tension 250ft-lb / 340N-m

Figure : 2.3 Bolt Tension.

Figure : 2.2 Disc Arm Identification.

2.1 2.1

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 1

6/02/2023 9:31:07 AM

THIS PAGE IS LEFT INTENTIONALLY BLANK

2915P Op & safety manual.indb 2

6/02/2023 9:31:07 AM

Safety Information SAFETY INFORMATION RISK MANAGEMENT

Risk management is the process of finding out what may cause an injury, deciding what may happen as a result, and doing something about it. The steps of risk management are: • Identify the hazards to workplace health and safety arising from work activities. • Assess the risks.

• Determine and implement control measures to reduce risk. • Monitor and review the effectiveness of the control measures. IDENTIFYING HAZARDS

Prior to commencing work, all hazards related to the work tasks should be identified. The selection of the appropriate work procedure(s) will depend on the type of work procedure(s) and hazards involved. Regular safety inspections will also identify hazards and ensure that control measures are in place. RISK ASSESSMENT Risk assessment allows appropriate control measures to be developed. Once hazards have been identified, they should be assessed in terms of their potential to do harm. To assess risk, consideration should be given to probability and consequences. 3.SAFETY INFORMATION - Risk Assessment Matrtix. RISK CONTROL Risk control is the process of eliminating or reducing risk factors. Control measures should be chosen and implemented to eliminate or reduce risk as far as practicable. When deciding on the most appropriate measures to use, practicality and acceptance of the control measures should be considered. Safe Working Procedures will be developed for all high – medium risk hazards. MONITOR AND REVIEW CONTROL MEASURES The risk identification, assessment and control process requires regular monitoring to ensure the implemented control measures perform as originally intended and continue to prevent or adequately control the risk of injury or incident. Control measures should also be checked carefully to ensure that new hazards are not created, directly or indirectly, by the original control measures.

3.1 3.1

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 1

6/02/2023 9:31:07 AM

Safety Information

RISK ASSESSMENT MATRIX

AT ALL TIMES COMPLY WITH RECOMMENDATIONS AND REQUIREMENTS OF THE MANU- FACTURER AND THE ENVIRONMENTAL PROTECTION AUTHORITY.

ALL HAZARDS & RISKS ARE CONTROLLED THROUGH SAFE WORKING PROCEDURES & ADEQUATE SIGNAGE.

IT IS IMPORTANT THAT THE OPERATOR CONDUCT THEIR OWN RISK ASSESSMENT FOR OPERATING THE MACHINE.

How likely is it to be that bad

How severly could it hurt someone? or How ill could it make someone? kill or cause permanent disability or ill health long term illness or serious injury medical attention and several days off work

Very unlikely could happen but probably never will

Very likely could happen anytime

Likely could happen anytime

Unlikely could happen but very rarely

1

1

2

3

1

2

3

4

2

3

4

5

3

4

5

6

first aid needed

The numbers show you how important it is to do something. 1: top priority: Do something immediately. 6: low priority: Do something when possible.

Figure : 3.1 Risk Assessment Matrix.

3.2

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 2

6/02/2023 9:31:07 AM

Safety Information

RISK ASSESSMENT TABLE

RISKS ASSOCIATED WITH YOUR MACHINE INCLUDE BUT ARE NOT LIMITED TO, THE RISKS IDENTIFIED IN THE FOLLOWING TABLE.

RISK SCORE

REVISED RISK SCORE

CODE

HAZARDS

CONTROL

ADJUSTING & CLEANING MUST ONLY BE DONE WHEN MACHINE IS LOWERED OR IN TRANSPORT POSITION AND ONLY AFTER ALL CHAINS AND BOLTS HAVE BEEN CHECKED FOR TIGHTNESS & WEAR IN THE LOWER POSITION. ENSURE JACK IS INSTALLED CORRECTLY & JACK RECEIVES REGULAR MAINTENANCE. KEEP FEET AND BODY CLEAR WHEN OPERATING. ENSURE NO PERSONNEL ARE BETWEEN TRACTOR & IMPLEMENT WHEN HITCHING/ UNHITCHING TRACTOR TO IMPLEMENT. MACHINE MUST BE LOWERED INTO WORKING POSITION USING SUITABLE LIFTING EQUIPMENT BEFORE PRIMING IS EFFECTED. PRIME BY SLIGHTLY LOOSENING FITTING/S INTO CYLINDERS AND OPERATING TRACTOR HYDRAULICS TO ACHIEVE FULL UNINTERRUPTED TRAVEL OF CYLINDER SEVERAL TIMES TO BLEED AIR. THEN RE-TIGHTEN HYDRAULIC FITTINGS. ENSURE JACK(S) ARE CORRECTLY POSITIONED AND TAKING WEIGHT BEFORE REMOVING DRAWBAR PIN. STICKERS WARN OPERATOR. MAINTAIN REGULAR CHECKS ON HYDRAULIC SYSTEM FOR WEAR & CHECK ALL FITTINGS ARE SECURE. ENSURE TRACTOR OIL FLOW IS LIMITED TO REDUCE FALLING SPEED OR DO NOT INTERRUPT MACHINE FALLING UNTIL MACHINE IS FULLY IN LOWERED POSITION. SAFETY PINS MUST BE PUT IN PLACE AS SOON AS MACHINE IS PUT IN TRANSPORT POSITION AND IF TRAVELLING ON PUBLIC ROADS TO DISCONNECT HYDRAULICS FROM TRACTOR.

CRUSHING - WHEN ADJUSTING AND CLEANING, AS MACHINE MAY DROP WITHOUT WARNING.

1(A).

1

5

CRUSHING - IMPROPER USE OF JACK.

1(B).

1

5

CRUSHING - WHEN HITCHING TRACTOR.

1(C).

2

5

CRUSHING - PRIOR TO PRIMING HYDRAULIC SYSTEM, AS MACHINE MAY DROP WITHOUT WARNING.

1(D).

1

5

SUDDEN LIFT OR DROP OF DRAWBAR, CAUSING SEVERE INJURY IF MACHINE BECOMES UNHITCHED. PENETRATION OF OIL - BROKEN OR BADLY MAINTAINED HYDRAULIC LINES. RUPTURE OF OIL LINES BY OVER PRESSURE WHEN MACHINE COMES TO SUDDEN STOP BEFORE FULLY LOWERED TO WORKING POSITION. COLLISION - HYDRAULICS ACCIDENTALLY LOWERED WHEN MACHINE IS BEING OPERATED IN TRANSPORT.

1(E).

1

5

2(A).

2

5

2(B).

2

5

3.

1

5

Figure : 3.2 Risk Assessment Table.

3.33.3

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 3

6/02/2023 9:31:07 AM

Safety Information

IMPORTANT SAFETY NOTICE (MUST READ)

It is the responsibility of the operators to read and understand your manual. Take time to familiarize yourself with the operation of this machine, particularly the safety signs and devices fitted to this machine.

USE OF MACHINE BEYOND ITS LIMITS OR INTENT OF OPERATION WILL VOID WARRANTY.

Slow down in terrain such as rocks, or other difficult operating conditions. • Safe work procedure analysis must be performed before attempting to as- semble this machine. • Do not attempt to operate this equipment under the influence of Drugs & Alcohol. • K-Line Ag can not be held responsible for any injury, death or property damage in the process of assembling this machine. • Ensure hydraulic system is fully primed 3. HYDRAULIC OPERATION & SAFETY - Priming Hydraulic System .

For further information please contact AU: 1800 194 131

3.4

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 4

6/02/2023 9:31:07 AM

Safety Information

SAFETY...YOU CAN LIVE WITH IT YOUR SAFETY & THE SAFETY OF OTHERS IS IMPORTANT

• BE PREPARED! • BE SAFE! • BE AWARE! • BE SEEN!

SAFETY ALERT SYMBOL When you see this symbol, you must be alert to the possibility of injury or death. SIGNAL WORDS The use of signal words, DANGER, WARNING AND CAUTION relate to the safety message. The appropriate signal word is selected when using the following guidelines.

Indicates an imminently hazardous situation that if not avoided WILL result in serious injury or death if proper safety measures are not taken.

Indicates a potentially hazardous situation that, if not avoided COULD result in serious injury or death if proper safety measures are not taken .

Indicates potentially hazardous situation that, if not avoided MAY result in serious injury or death if proper safety measures are not taken.

Figure : 3.3 Danger !

Figure : 3.4 Warning !

Figure : 3.5 Caution !

All operators must understand and abide by maintenance safety procedures set out in this book. It is the responsibility of the Operator (and maintenance personnel) to ensure that on this machine, ALL SAFETY SIGNS AND DEVICES are working correctly and all safety signs are legible.

FAILURE TO OBSERVE THE INSTRUCTIONS OF THIS BOOKLET COULD RESULT IN SERI- OUS INJURY OR DEATH.

3.53.5

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 5

6/02/2023 9:31:07 AM

Safety Information

SAFETY DECALS

SAFETY DECAL PLACEMENT

Figure : 3.6 Safety Decal Placement.

DECALS USED ON MACHINE A B C D F G H J K LMNO P Q.2CR TUW X[A/B] 181121111122110 1 1 1 1 1 8

Figure : 3.7 Decals Used On Machine.

3.6

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 6

6/02/2023 9:31:08 AM

Safety Information

SAFETY DECAL PART NUMBERS

BOM ID

PART NUMBER

DESCRIPTION

(A) 9WD-W022

A

DECAL. WARNING TRANSPORT SPEED 160MM X 120MM. ORANGE - BLACK ON WHITE

(B) 9WD-C023

B

DECAL. CAUTION WHEEL NUT TENSION 160MM X 40MM. YELLOW- BLACK

(C) 9WD-W05

C

DECAL. WARNING CRUSHING 160MM X 80MM. ORANGE - BLACK ON WHITE

(D) 9WD-D04

D

DECAL. DANGER ELECTRIC SHOCK 160MM X 80MM. RED - BLACK ON WHITE

(E) 9WD-D01H

E

DECAL. DANGER CRUSHING WING (HORIZONTAL) 180MM X 70MM. RED - BLACK

(F) 9WD-D01V

F

DECAL. DANGER CRUSHING WING (VERTICAL) 70MM X 180MM. RED - BLACK

(G) 9WD-W021

G

DECAL. WARNING OPERATING INSTRUCTIONS 160MM X 60MM. ORANGE - BLACK

(H) 9WD-C04

H

DECAL. CAUTION SERIOUS INJURY 140MM X 140MM. YELLOW - BLACK

(I) 9WD-I01

I

DECAL. IMPORTANT DAILY GREASE PURGE 100MM X 40MM. BLUE - BLACK

(J) 9WDW-T5

J

DECAL. WARNING HIGH PRESS. FLUID 160MM X 80MM. ORANGE - BLACK

(K) 9WDD-T3

K

DECAL DANGER CRUSHING MACH. IMPLEMENT 160MM X 80MM. RED - BLACK

(L) 9WD-W024

L

DECAL. WARNING HYDRAULIC PRIME 160MM X 60MM. ORANGE - BLACK ON WHITE

(M) 9WD-W10

M

DECAL. WARNING PINCH POINT 100MM X 70MM. ORANGE - BLACK ON WHITE

(N) 9WD-W01

N

DECAL. WARNING STEPPING ON WHEELS 160MM X 60MM ORANGE - BLACK ON WHITE

(O) 9WD-D01

O

DECAL. DANGER UPTHRUST 200MM X 70MM. RED - BLACK ON WHITE

(P) 9WD-R01

P

DECAL. RAM STOP COMBINATION 300MM X 80MM. MULTI-COLOUR

(Q.1A) 9WD.F01DC6TPI (Q.2A) 9WD.F01TC2TPI (Q.2B) 9WD.F01TC3TPI (Q.2C) 9WD.F01TC4TPI (Q.2D) 9WD.F01TC5TPI

Q.1A Q.2A Q.2B Q.2C Q.2D

DECAL DEPTH CONTROL 6 TURNS PER INCH 100 X 70 DECAL TILT CONTROL 2 TURNS PER INCH 100 X 70 DECAL TILT CONTROL 3 TURNS PER INCH 100 X 70 DECAL TILT CONTROL 4 TURNS PER INCH 100 X 70 DECAL TILT CONTROL 5 TURNS PER INCH 100 X 70

(R) 9WD-S01

R

DECAL. 32-KMH/ 20-MPH 190MM X 80MM. RED - BLACK ON WHITE

(T) 9WD-H02

T

DECAL. 5 COLOUR HYDRAULIC COLOURS 160MM X 100MM. MULTI-COLOUR DECAL.

(U) 9WD-I02

U

DECAL. IMPORTANT DISC BOLT RETORQUE 100MM X 80MM. BLUE- BLK

(W) 9WD-F04

W

DECAL 5 COLOUR FOLD-UNFOLD 280MM X 180MM. RED - BLACK ON WHITE

(XA) 9WD-I-425-65-225 (XB) 9WD-I-500-60-225 (XC) 9WD-I-400-60-155

XA XB XC

DECAL TYRE PRESSURE + WHEEL NUT TORQUE - 425/65R22.5 DECAL TYRE PRESSURE + WHEEL NUT TORQUE - 500/60R22.5 DECAL TYRE PRESSURE + WHEEL NUT TORQUE - 400/60R15.5

(Y) 9WD-WD1

Y

DECAL. WHEEL DEPTH 330MM X 140MM. BLACK

Figure : 3.8 Safety Decal Part Numbers.

3.73.7

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 7

6/02/2023 9:31:08 AM

Safety Information

DECALS

NOTE: NOT ALL DECALS GO ON ALL MODELS. (See SAFETY INFOR- MATION Safety Decal Placement)

(A) 9WD-W022

(B) 9WD-C023

(F) 9WD-D01V

(G) 9WD-W021

(C) 9WD-W05

(D) 9WD-D04

(H) 9WD-C04

(E) 9WD-D01H

(I) 9WD-I01

3.8

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 8

6/02/2023 9:31:09 AM

Safety Information

(J) 9WDW-T5

(M) 9WD-W10

(K) 9WDD-T3

(N) 9WD-W01

(L) 9WD-W024

(O) 9WD-D01

(P) 9WD-R01

(R) AUS SPEED STICKER MAX 32KPH/20MPH

3.93.9

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 9

6/02/2023 9:31:10 AM

Safety Information

(Q.2A) 9WD.F01TC2TPI

(Q.2B) 9WD.TC3TPI

(Q.1A) 9WD.F01DC6TPI

(Q.2C) 9WD.F01TC4TPI

(Q.2D) 9WD.TC5TPI

(U) 9WD-I02

(T) 9WD-H02

(W) 9WD-F04

NOTE: Wheel depth sticker: white with cut outs (shown as black)

(XA) 9WD-I-425-65-225

(XB) 9WD-I-500-60-225

(Y) 9WD-WD1

(XC) 9WD-I-400-60-155

3.10

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 10

6/02/2023 9:31:11 AM

Safety Information

LOGO STICKERS

LARGE SPEEDTILLER STICKER: 1410 X 210MM (1 x either side of drawbar) (1 x back of mainframe) SMALL SPEEDTILLER STICKER: 677 X 100MM (1 x front of each wing weldment)

Figure : 3.9 Large Logo Sticker.

K-LINE AGRICULTURE STICKER: 380 X 125MM (1 x front of each wing fold weldment)

Figure : 3.10 K-Line Agriculture Sticker.

Centre between arrows shown in images below.

BACK OF MAINFRAME

Figure : 3.11 Side View Of Decals

Figure : 3.13 Back Of Mainframe Decal

Figure : 3.12 Full View Decal Placement

3.113.11

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 11

6/02/2023 9:31:11 AM

Safety Information

SAFETY SIGN CARE • Keep safety signs clean and legible at all times. • Replace safety signs that are missing or have become illegible. TO ORDER SAFETY DECALS CONTACT: Australia: K-Line Agriculture

• Replaced parts that displayed a safety sign should also display the current sign.

USA: Contact the dealer your machine was purchased from.

PO Box 340 74 Young Rd Cowra NSW 2794 Email: sales@k-line.net.au Free-call: 1800 194 131

HOW TO INSTALL SAFETY SIGNS: • Be sure that the installation area is clean and dry. • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the split backing paper.

• Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. • Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. • Failure to comply could result in serious injury or death.

Figure : 3.15 Safety Decal Placement. (3. SAFETY INFORMATION - Safety Decal Placement)

Figure : 3.14 Locate Where Necessary.

3.12

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 12

6/02/2023 9:31:12 AM

Safety Information

TYRE SAFETY & PRESSURES SERVICING PROCEDURES OPERATIONAL SAFETY

Always cage tyres before seating beads.

Never exceed stated pressures when seating beads.

Do not attempt to mount a tyre unless you have the suitable equipment and experienced personnel.

Figure : 3.16 Tyre Safety Warning !

Inflating tyres can be dangerous. Always

stand to the side when inflating.

Failure to comply could result in serious injury or death.

Load ratings of replacement tyres should

meet or exceed weight requirements.

For correct Tyre pressure refer to 1. SPECIFI- CATIONS - Tyre Specification Table. Before mounting wheel to machine, check all hub and rim contact surfaces are undamaged and free of paint, dirt and grease. Lubricate wheel stubs with standard viscosity oil. Tension wheel nuts to the correct specification according to tyre size refer to 1. SPECIFICATIONS - Tyre Specification Table. For field operation: Re-tension after 1st, 5th, then every 50 hrs of operation. For road travel re-tension first 3 miles (5kms), 10 miles (15kms), and thereafter at 25 miles (40kms) intervals.

Figure : 3.17 Warning ! Tyre Pressure.

TYRE PRESSURE MAY VARY DEPENDING ON TYRES USED.

3.13.13

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 13

6/02/2023 9:31:12 AM

Safety Information

POWER LINES POWER LINES CAN ARC & ELECTROCUTE WITHOUT COMING IN DIRECT CONTACT

Consult electricity authorities and all relevant energy companies to determine safe working distances from overhead power lines etc. BEFORE operation of this machine: • Ensure all operators are familiar with this manual and all safety devices and features of the machine. • Take every reasonable precaution as is commonly expected in this industry and in the operation of the machine.

• Maintain the machine at all times in a condition that is safe to operate, and ensure it complies with any relevant safety acts of parliament, government authorities and regulations.

Figure : 3.18 Danger ! ‘Electric Shock Can Kill’.

3.14

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 14

6/02/2023 9:31:13 AM

Safety Information

HYDRAULIC OPERATION & SAFETY

HYDRAULIC SYSTEM FAILURE

IN THE EVENT OF HYDRAULIC SYSTEM FAILURE OR HYDRAULIC HOSE RUPTURE, YOU MUST FOLLOW THE STEPS SET OUT BELOW:

ESCAPING HYDRAULIC FLUID IS DANGEROUS AND CAN CAUSE SERIOUS INJURY OR DEATH.

STEP 1: PREPARE FOR SHUTDOWN. • Immediately return hydraulic lever to neutral position. • Stop operating machine. STEP 2: SHUTDOWN THE EQUIPMENT. • Use hydraulic lever to lower machine to ground (if in raised position). STEP 3: ISOLATE THE EQUIPMENT. • Freely operate remote levers to release residual pressure from system. • If tractor is equipped, place levers in float position. • Shut down tractor. STEP 4: APPLY THE LOCKOUT / TAG-OUT DEVICE. • Disconnect all hydraulic hoses from tractor remotes. • Place Lockout or Out of Service Tags on all hoses.

STEP 5: CONTROL THE STORED ENERGY. • Ensure no hydraulic pressure remains in the system. Slowly release bleed tap (if equipped), or slightly loosen one hydraulic connection on each circuit to allow any re- maining fluid under pressure to be released. STEP 6: VERIFY ISOLATION OF EQUIP- MENT. • Double check the steps and verify that the equipment has been shut down and has the Lock and Tag Labels evident to prohibit operation. Have repairs carried out and defective parts replaced. Do not re-connect to tractor or other hydraulic power source, un- til system has been fully tested.

3.153.15

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 15

6/02/2023 9:31:13 AM

Safety Information

HYDRAULIC OPERATION

WARNING Hydraulic fluid escaping under pressure can have sufficient force to cause injury. Keep all hoses and connections in good serviceable condition. Failure to heed may result in serious personal injury or death. Escaping hydraulic fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving the pressure before disconnecting lines or performing work on the system. Make sure hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condi- tion before applying pressure to the system. Use a piece of paper or cardboard, NOT BODY PARTS, to check for suspected leaks. Wear protective gloves and safety glasses or goggles when working with hydraulic systems. DO NOT DELAY! If an accident occurs, see a doctor familiar with this type of injury immediately. Any fluid injected into the skin or eyes must be treated within a few hours or gangrene may result.

HYDRAULIC HOSE HOOK UP • For ease of hook up, hose grip handles are color coded. • The same color is used for each hydraulic circuit. • To distinguish between EXTEND and RETRACT, hose grips are marked accordingly. • Clean hydraulic hose breakaway ends before connecting to tractor.

• Hose grip circuits are color coded and marked accordingly for In & Out. • After disconnecting tractor, ensure hydraulic hoses are safely stored in the hose holder.

ENSURE HYDRAULIC SYSTEM IS FULLY PRIMED BEFORE USE

PRIMING HYDRAULIC SYSTEM • Fully extend and retract hydraulic cylinders. • Repeat 3-4 times and hold lever extended each way for 10 to 15 seconds to release air from the system. If problem exists hold hydraulic lever under pressure, until air is fully released from system.

3.16

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 16

6/02/2023 9:31:13 AM

Safety Information

HYDRAULIC COLOUR CODES

HOSE GRIP COLOR CODES

RECOMMENDED PORT NUMBER

COLOUR FROM JUNE 2021

COLOUR PRE JUNE 2021

FUNCTION

RED

1

WHEEL LIFT

RED

2 3 4 5

FORE & AFT (TILT)

BLUE

YELLOW

WING FOLD

YELLOW

GREEN

ROLLER (OPTION)

GREEN

BLUE

JACK LIFT

ORANGE

GREEN YELLOW

Figure : 3.19 Hose Grip Colour Codes.

Figure : 3.20 Colour Pre June 2021.

WHEEL CIRCUIT

out

extend

in

retract

FOR & AFT (TILT) CIRCUIT

out

extend

in

retract

WING CIRCUIT

out

extend

in

retract

ROLLER CIRCUIT

out

extend

in

retract

JACK CIRCUIT

out

extend

in

retract

Figure : 3.21 Hydraulic Circuit Colour Codes.

3.173.17

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 17

6/02/2023 9:31:17 AM

Safety Information

OPERATING INSTRUCTIONS

HOOKING / UNHOOKING TO TRACTOR

HOOKING UP TO TRACTOR 1. Keep well clear when backing up to machine. 2. Shut down tractor. 3. Secure & lock drawbar pin in place. 4. Install safety chain by crossing the chains under the tongue and secure to the drawbar hitch frame of the tractor. 5. Clean all hydraulic couplings. 6. Hoses are color coded according to function 3.SAFETY INFORMATION - Hydraulic Co- lour Codes. 7. Beware of high pressure fluid. 8. Plug in hoses to respective remote ports. 9. Plug in electrical lead to tractor connection. 10. Release implement jack & store. 11. Check hydraulic cylinders are fully primed to avoid serious injury or death. Prime hydrau- lic system 3.HYDRAULIC OPERATION & SAFETY- Priming Hydraulic System. UNHOOKING 1. Machine must be fully lowered or in transport position with safety locks engaged. 2. Use wheel chocks. 3. Release hydraulic pressure from system. 4. Lock Implement jack in place. 5. Wind implement jack to take weight of machine off tractor drawbar. 6. Disconnect hydraulic hoses. 7. Disconnect electrical lead (if fitted). 8. Remove safety chains and drawbar pin. NOTE; If implement jack is damaged DO NOT USE, replace immediately, or severe bodily harm may result. ELECTRICAL CONNECTION HOOK UP (If Fitted) 1. Ensure tractor and machine electrical con- nections are compatible. 2. Plug lead into tractor terminal. 3. Test lighting prior to road travel. (Power not required for field work.)

Figure : 3.22 Danger! CRUSHING HAZARD.

Figure : 3.23 Warning ! HIGH PRESSURE FLUID.

Figure : 3.24 Warning ! CRUSHING OF THE BODY.

3.18

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 18

6/02/2023 9:31:17 AM

Safety Information

TRANSPORTING / ROADING

1. Wheel lift may be lowered for transport. 2. Ensure towing unit weight is the same as or greater than the towed unit. 1. SPECIFICATION - Model Specifications . 3. Lockout tractor drawbar swing mechanism (must be in fixed position). 4. Ensure tires are correctly inflated. 1. SPECIFICATION - Model Specifications . 5. Check wheel nut tension. 1. SPECIFICATION - Model Specifications . NOTE: Refer to Wheel Stud Torque Tightening Sequence. 5.MAINTENANCE - Torque Tighten- ing Sequence . 6. Ensure all safety locks are engaged. 7. Ensure tractor brakes are latched together at all times. 8. Plan your route to avoid heavy traffic. 9. Observe bridge load ratings. TIP OVER HAZARD NOTICE: This is an unbraked implement. Use extreme caution when turning, and on steep terrain. Maximum towing speed is 20mph (32km/ hr). DO NOT EXCEED AT ANY TIME. NOTICE: NEVER transport machine on public roads without complying with Federal and State laws and local regulations governing the safe movement of farm machinery.

Figure : 3.25 Warning ! ROADING / TRANSPORT.

Figure : 3.26 Danger ! CRUSHING HAZARD.

3.193.19

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 19

6/02/2023 9:31:17 AM

Safety Information

FOLDING / UNFOLDING MACHINE

BEWARE OF CRUSHING HAZARD WHEN ENGAGING & DISENGAGING SAFETY LOCKS & IN THE OPERATION OF THE WING FOLDING MECHANISM.

FAILURE TO COMPLY WILL RESULT IN SERIOUS INJURY OR DEATH.

ALWAYS LIFT MACHINE WITH WHEEL LIFT BEFORE FOLDING/UNFOLDING TO AVOID DAMAGE. NOTE: Beware of pinch points in wing lift area when securing or releasing safety locks. NOTE: Never stand within radius of wings when in raised position, or folding and unfolding. TO UNFOLD MACHINE 1. Fully raise with wheel lift. 2. Release safety pins. 3. Lift wings just free of lift saddle by operating tilt hydraulics (BLUE). 4. Extend wing cylinders to open position (YELLOW). 5. Lower tilt cylinders to work position (BLUE). TO FOLD MACHINE 1. Fully raise with wheel lift. 2. Fully raise tilt (BLUE), and back off slightly so the wings at closing will contact saddle correctly. 3. Fold wings into saddle (YELLOW).

Figure : 3.27 Warning ! PINCH POINT.

Figure : 3.28 2915P Safety Locks

4. Lower into position (BLUE). 5. Secure safety locks or pins.

Figure : 3.29 Danger ! UPTHRUST FORCE.

NOTE: Tractor weight must be equal to machine weight. NOTE: Drawbar pin must be securely fastened with safety chains in place.

DANGER: BEWARE OF UPTHRUST AND DOWN/THRUST ON DRAWBAR DURING OPERATION.

3.20

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 20

6/02/2023 9:31:17 AM

Field Operation

FIELD OPERATION

WARNING: USE OF MACHINE BEYOND ITS LIMITS OR INTENT OF OPERATION WILL VOID WARRANTY.

SPEED RANGE • 8-15km/hr (5-9 mph). • Speed variable to suit conditions. NOTICE: Slow down in terrain such as rocks or other difficult operating conditions. WARNING In field adjustments machine must be: • Lowered to ground OR • Placed in raised position with all safety locks engaged with engine shut down.

IT IS THE RESPONSIBILITY OF THE OPERATORS TO: Read and understand your manual. Take time to familiarize yourself with the operation of this machine, particularly the safety signs and devices fitted to this machine.

FAILURE TO COMPLY COULD RESULT IN SERIOUS INJURY OR DEATH.

4.14.1

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 1

6/02/2023 9:31:17 AM

Field Operation

SPEEDTILLER START UP TIPS

THIS IS A GUIDE ONLY AND MUST BE READ IN CONJUNCTION WITH INSTRUCTION MANUAL.

1. DEPTH CONTROL • Start by setting roller 40mm higher than discs on level service. • Ensure wing roller heights are set the same. (Folding wing models only).

Tracking Left

Tracking Right

Front disc too high

Front disc too low

Figure : 4.1 Tracking Adjustments.

2. TILT ADJUSTMENT (SETTING TO REDUCE SIDEWAYS TRACKING) • Start with front disc 20mm higher than back discs. • Follow diagram for tilt settings.

• To adjust, turn front adjuster and lock. 3. FRONT LATERAL DISC POSITIONING • Front lateral disc positioning is factory set for standard operating conditions. • If adjustment is needed follow 4. FIELD OPERATION - Lateral Front Disc Gang Positioning . 4. WING DOWN PRESSURE • It is recommended to place wing fold circuit (YELLOW) in float mode. • Apply wing down pressure only where soil is hard and dry See 4. FIELD OPERATION - Tracking Adjustments 5. SPEED RANGE • 8-15km/hr. (5.9mph). • Greater activity occurs at higher speeds. • Slow down in rough terrain (such as rocky country). 6. HEADLANDS/TURNING • Always slightly raise machine when performing headlands (turning at end of run) etc. • For 3 Point Linkage machines, raise machine with Tractor Linkage Height Adjustment so discs and rollers are not in contact with ground. • For Trailing and Powerflex machines, raise machine with wheels so discs and rollers are just out of contact with ground. 7. ROAD TRAVEL SPEED LIMIT • 32kmh (20mph).

4.2

2915P Speedtiller Powerflex

OPERATOR & SAFETY MANUAL

2915P Op & safety manual.indb 2

6/02/2023 9:31:17 AM

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46 Page 47 Page 48 Page 49 Page 50 Page 51 Page 52 Page 53 Page 54 Page 55 Page 56 Page 57 Page 58 Page 59 Page 60 Page 61 Page 62 Page 63 Page 64 Page 65 Page 66 Page 67 Page 68 Page 69 Page 70

www.k-line.net.au

Made with FlippingBook - Online Brochure Maker