Vektek Gerardi Instructions

Flex Vise

Standard VISE

Mounting and disassembling Montaje y desmontaje Mounting Make sure the base is free of any obstacles to prevent the vise from bolting down level. Disassembly for maintenance and longer life: - Disassemble the fixed jaw (A) by removing the four upper bolts (B); - Loosen the set screws (C) from the clamping device to unlock the ball (D); - Remove the clamping device by moving it to the end of the vise base, then unlock it from the seat of the movable jaw; - Remove the movable jaw (E); - In order to remove the jaw plates (F) unscrew the bolts (G) in the back of the jaws; - Be careful not to lose the two springs (H) placed under the each jaw plate. - Wash and oil all the separated parts; - Reassemble the vise by retracing the steps backwards. - Check that the vise reflects the tolerances of the initial setting .

Mounting Make sure the base is free of any obstacles to prevent the vise from bolting down level. Disassembly for maintenance and longer life: - Disassemble the fixed jaw (A) by removing the four upper bolts (B); - Loosen the set screws (C) from the clamping device to unlock the ball (D); - Remove the clamping device by moving it to the end of the vise base, then unlock it from the seat of the movable jaw; - Remove the movable jaw (E); - Extract the quick change jaw plates from their seat (F); - Unlock the sliding plate of the movable jaw by unscrewing the lower screws (G); - Wash and oil all the separated parts; - Reassemble the vise by retracing the steps backwards. - Check that the vise reflects the tolerances of the initial setting . Mounting and disassembling Montaje y desmontaje

TM

Montaje Asegúrese de que la base esté libre de obstáculos que eviten que la prensa se atornille al nivel. Desmontaje para mantenimiento y mayor duración: - Desmontar la mordaza fija (A) quitando los cuatro pernos superiores (B); - Afloje los tornillos de fijación (C) del elemento de clampeo para desbloquear la bola de estacionamiento (D); - Retire el elemento de clampeo moviéndolo a al final de la base de la prensa, luego desbloquéela del asiento de la mordaza móvil; - Retire la mordaza móvil (E); - Remueva de su asiento las placas de cambio rápido de la mordaza (F); - Desbloquee la placa deslizante de la mordaza móvil desenroscando los tornillos inferiores (G); - Lave y engrase todas las partes separadas; - Vuelva a ensamblar la prensa siguiendo los pasos anteriores pasos hacia atrás - Compruebe que la prensa refleje las tolerancias de la configuración inicial.

Montaje Asegúrese de que la base esté libre de obstáculos que eviten que la prensa se atornille al nivel. Desmontaje para mantenimiento y mayor duración: - Desmontar la mordaza fija (A) quitando los cuatro pernos superiores (B); - Afloje los tornillos de fijación (C) del elemento de clampeo para desbloquear la bola de estacionamiento (D); - Retire el elemento de clampeo moviéndolo a al final de la base de la prensa, luego desbloquéela del asiento de la mordaza móvil; - Retire la mordaza móvil (E); - Para retirar las placas de la mordaza (F) desenroscar los tornillos (G) en la parte posterior de las mordazas; - Tenga cuidado de no perder los dos resortes (H) colocados debajo de cada placa de mordaza. - Lave y engrase todas las partes separadas; - Vuelva a montar el tornillo de banco volviendo sobre pasos hacia atrás - Compruebe que la prensa refleje las tolerancias de La configuración inicial.

C

C

E

E

F

D

D

F

B

B

G

A

H

A

G

16

17

Made with FlippingBook - Online Brochure Maker