Grooving Tools TGA Inserts
(
Coated Carbide /
Cermet /
Carbide /
CBN-SUMIBORON /
PCD-SUMIDIA)
Fig 1
± 0.025
GAN
CW
Cutting Edge GAN
Grade
Coated Carbide AC530U
15° 25° 15° 15° 10°
RE
RE
Honing
H1
Sharp Edge
IC
Carbide
Coated Cermet T3000Z Coated Cermet T2500Z
Honing Honing
T1500A
Sharp Edge
Cermet
SUMIBORON BN2000
Negative Land 5°
DA2200
15°
Sharp Edge
SUMIDIA
S
Figure shows right hand (R) tool.
* For the rake angle when tted on the holder, refer to page F44.
F
Square Edged Grooving Insert
Dimensions (mm)
Maximum Groove Depth (mm) CDX
Nose Radius RE
Inscribed Circle IC
Thickness
AC530U H1 T2500Z T3000Z T1500A BN2000 DA2200 Width of Cut CW RLRLRLRLRLRLRL
Maximum Depth of Cut
*Group No.
Cat. No.
Fig
Internal Diameter
O.D.
S
TGA R/L3033(E) TGA R/L3050(E) TGA R/L3075(E) TGA R/L3095(E) TGA R/L3100(E) TGA R/L3110(E) TGA R/L3125(E) TGA R/L3135(E) TGA R/L3145(E) TGA R/L3150(E) TGA R/L3165(E) TGA R/L3175(E) TGA R/L3185(E) TGA R/L3200(E) TGA R/L3220(E) TGA R/L3230(E) TGA R/L3250(E) TGA R/L3265(E) TGA R/L3270(E) TGA R/L3280(E) TGA R/L4125(E) TGA R/L4145(E) TGA R/L4150(E) TGA R/L4165(E) TGA R/L4175(E) TGA R/L4185(E) TGA R/L4200(E) TGA R/L4220(E) TGA R/L4230(E) TGA R/L4250(E) TGA R/L4265(E) TGA R/L4270(E) TGA R/L4280(E) TGA R/L4300(E) TGA R/L4320(E) TGA R/L4330(E) TGA R/L4350(E) TGA R/L4370(E) TGA R/L4390(E) TGA R/L4400(E) TGA R/L4410(E) TGA R/L4420(E) TGA R/L4430(E) TGA R/L4440(E) TGA R/L4450(E) TGA R/L4480(E)
● — — — — 0.33 0.8 0.5 1.0 0.05 9.525 3.18 — — — — 0.50 1.2 0.8 1.4 0.05 9.525 3.18
1 1 1 1
0.75 0.95 1.00 1.10 1.25 1.35 1.45 1.50 1.65 1.75 1.85 2.00 2.20 2.30 2.50 2.65 2.70 2.80 1.25 1.45 1.50 1.65 1.75 1.85 2.00 2.20 2.30 2.50 2.65 2.70 2.80 3.00 3.20 3.30 3.50 3.70 3.90 4.00 4.10 4.20 4.30 4.40 4.50 4.80
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
*3 0.1
2.0 1.5 2.5
9.525 3.18
1
*3 0.1
9.525 3.18
1
2.5 2.0 3.0
*2 0.2
12.70 4.76
2
2.0 1.7 2.5
*2 0.2
12.70 4.76
3
3.5 2.5 3.9
*1 5.0 *1 5.0 *1 5.0
*1 5.4 *1 5.4
*2 0.3 *2 0.3 *2 0.3 *2 0.3
2.5
12.70 4.76
4
2.5
12.70 4.76
4
2.5 5.4
12.70 4.76
4
4.76
5.0 2.5 5.4
12.70
4
*2 0.4
5.00
* Add E as the part number suffix for T1500A. Select applicable inserts for the holders by using matching group numbers. *1: CDX = 4.4 (maximum groove depth 4.0) for SUMIBORON and SUMIDIA (2.5 for internal diameter machining) *2: RE = 0.2 for SUMIBORON; RE = 0.1 for SUMIDIA *3: T1500A is RE = 0.2
F45
Made with FlippingBook flipbook maker