WaveMill WEZ Series
Small Endmill Milling Cutter for Medical and Lathe (Small Machining)
■ Feed Rate Recommendations WEZ11 Tool: WEZ11016ES02-10 Insert: AOET11T3 〇〇 PEER-F
WEZ17 Tool: WEZ17025ES02-16 Insert: AOET1705 〇〇 PEER-F
.591
.591
f z : .002 IPT f z : .004 IPT f z : .006 IPT
f z : .0024 IPT f z : .0047 IPT f z : .0079 IPT
.472
.472
Cutting Width a e
H
.354
.354
.236
.236
Overhang 1.378”
.118
.118
0
.197 .394 .591 .787 1.000
0
.197 .394 .591 .787 1.000
Cutting Width a e (inch)
Cutting Width a e (inch)
For cutting conditions by part material, see page H53. When using G type chipbreakers, set the efficiency to 80%. The recommended cutting conditions may not be practical depending on the operating conditions (e.g. machine, work material shape, clamping system).
■ Excellent Squareness
WEZ
Comp. A (ø10mm Solid Carbide Endmill)
WEZ
Comp. A (ø10mm Solid C
-0.01 0 0.01 0.02 0.03 0.04 0.05 0.06
-0.01 0 0.01 0.02 0.03 0.04 0.05 0.06
9 WEZ presents a significant cost advantage when compared against solid carbide endmills.
(mm)
0
(mm) 2
4
6
8
10
12
Wall Height (mm)
1st Pass D.O.C. (6mm)
2nd Pass D.O.C. (6mm)
WEZ
Cylindrically Secured
0
2
4
6
8
10
Wall Height (mm)
Cutting Width 2mm
1st Pass D.O.C. (6mm)
Ideal for low-rigidity multi-tasking machines
2nd Pass D.O.C. (6mm)
WEZ
Cylindrica
0mm
6mm
12mm
Contact Surface Area
Cutting Width 2mm
Wall Height
Ideal for low-rigidity multi-tasking machines
Comp. A (ø10mm Solid Carbide Endmill)
0mm
6mm
12mm
Contact Surface Area
Cylindrically Secured
Machine: Multi-axis NC Lathe Part Material: 304 Stainless Steel, ø16mm Tool: WEZ11020ES03-10 (ø20mm, 3 flutes) Insert: AOET11T308PEER-F-ACU2500 Cutting Conditions: vc = 330 SFM, fz = .003 IPT, ap =.236“ x 2 passes, ae = .079“
Wall Height
Comp. A (ø10mm Solid Carbide Endmill)
Cylindrically Secured
■ Surface Quality
WEZ
Competitor B (ø10 Solid Carbide Endmill)
5
0
0.05mm
0.05mm
-5 （ µm （ ） ）
Ra 0.18µm Rz 1.3µm
Ra 2.94µm Rz 13.8µm
Larger tool diameter than carbide solid endmills enables reduced number of passes for high-efficiency machining! Good shoulder accuracy and machined surface quality which can eliminate a finishing pass.
Machine: Compound NC Lathe Work Material: 304 Stainless Steel, ø16mm Round Tool: WEZ11020ES03-10 (ø20mm, 3 flutes) Insert: AOET11T308PEER-F (ACU2500) Cutting Conditions: WEZ type, vc = 330 SFM, fz = .002 IPT, ap = .079”, ae = .472” Wet Competitor’s Product B: vc = 330 SFM, fz = .002 IPT, ap = .079, ”ae = .236” x 2 Passes, Wet (Carbide Solid Endmill)
H72
Made with FlippingBook flipbook maker