GSX MILL 4 Flute Endmills Sharp Edge GSX 40000S-2D Type
Recommended Cutting Conditions 1. For stable machining performance use rigid, high-precision machines and holders. 2. Use air blow when dry machining. 3. Use wet machining for stainless steel, heat-resistant alloy, and titanium alloy applications. 4. If chatter is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut. 5. This series is not recommended for groove milling. 6. If the machine cannot achieve the recommended spindle speed, please use the maximum spindle speed available.
a e
DC
Side Milling
I
Tempered Steel, Hardened Steel NAK , HPM (35 to 45HRC)
Carbon Steel SC (150 to 250HB)
Alloy Steel SCM (25 to 35HRC)
Work Material Cutting Conditions
Steel for Structure SS
Heat-Resistant Alloy Titanium Alloy
Hardened Steel (45 to 55HRC)
Stainless Steel SUS304,SUS316
Cast Iron FC
Spindle Speed (min -1 ) 22,000 11,500
Feed Rate (mm/min)
Spindle Speed (min -1 ) 22,000 11,500
Feed Rate (mm/min)
Spindle Speed (min -1 ) 22,000 11,500
Feed Rate (mm/min)
Spindle Speed (min -1 ) 19,000 11,000
Feed Rate (mm/min)
Spindle Speed (min -1 ) 13,000
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 ) 11,300
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
DC (mm)
9,500 5,400 2,900 2,000 1,450 1,200 1,000
9,500 5,400 2,900 2,000 1,450 1,200 1,000
1.0 2.0 4.0 6.0 8.0
360 440 560 600 600 600 600 500 460
360 440 560 600 600 600 600 500 460
360 440 560 600 600 600 600 500 460
220 290 370 400 400 400 400 320 290
140 180 230 240 240 240 240
90
90
65 85
7,500 4,000 2,700 2,000 1,600 1,350 1,000
110 150 160 160 160 160
6,500 3,400 2,400 1,800 1,450 1,200
120 160 170 170 170 170
6,000 4,200 3,000 2,500 2,100 1,500 1,200
6,000 4,200 3,000 2,500 2,100 1,500 1,200
6,000 4,200 3,000 2,500 2,100 1,500 1,200
5,800 4,000 2,800 2,350 2,000 1,450 1,150
100 120 120 120 120
10.0 12.0 16.0 20.0 25.0
210 750 130
900 140 750 90
800 200 640 160
600 110
700 120
600 480
75 60
960 370
960 370
960 370
920 230
480
85
560
95
2.0DC
a p a e
Standard Depth of Cut
0.03DC
0.01DC
Groove Finishing
Tempered Steel, Hardened Steel NAK , HPM (35 to 45HRC)
Carbon Steel SC (150 to 250HB)
Alloy Steel SCM (25 to 35HRC)
Work Material Cutting Conditions
Steel for Structure SS
Heat-Resistant Alloy Titanium Alloy
Hardened Steel (45 to 55HRC)
Stainless Steel SUS304,SUS316
Cast Iron FC
Spindle Speed (min -1 ) 22,000 11,500
Feed Rate (mm/min)
Spindle Speed (min -1 ) 22,000 11,500
Feed Rate (mm/min)
Spindle Speed (min -1 ) 22,000 11,500
Feed Rate (mm/min)
Spindle Speed (min -1 ) 19,000 11,000
Feed Rate (mm/min)
Spindle Speed (min -1 ) 13,000
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
Spindle Speed (min -1 ) 11,300
Feed Rate (mm/min)
Spindle Speed (min -1 )
Feed Rate (mm/min)
DC (mm)
9,500 5,400 2,900 2,000 1,450 1,200 1,000
9,500 5,400 2,900 2,000 1,450 1,200 1,000
1.0 2.0 4.0 6.0 8.0
360 440 560 600 600 600 600 500 460
360 440 560 600 600 600 600 500 460
360 440 560 600 600 600 600 500 460
220 290 370 400 400 400 400 320 290
140 180 230 240 240 240 240
90
90
65 85
7,500 4,000 2,700 2,000 1,600 1,350 1,000
6,500 3,400 2,400 1,800 1,450 1,200
110 150 160 160 160 160
120 160 170 170 170 170
6,000 4,200 3,000 2,500 2,100 1,500 1,200
6,000 4,200 3,000 2,500 2,100 1,500 1,200
6,000 4,200 3,000 2,500 2,100 1,500 1,200
5,800 4,000 2,800 2,350 2,000 1,450 1,150
100 120 120 120 120
10.0 12.0 16.0 20.0 25.0
210 750 130
900 140 750 90
800 200 640 160
600 110
700 120
600 480
75 60
960 370
960 370
960 370
920 230
480
85
560
95
1.5DC
a p a e
Standard Depth of Cut
Below 0.02DC
I 63
Made with FlippingBook flipbook maker