Tool Balancer Adjustment
B
For ATS-15 (balancer 9312MZ) & ATS
TS-25 (balancer 9313MZ) models
A
To allow the tool balancer to operate heavier loads within the load capacity accepted, turn knob (A) anticlockwise, indicated by the “+” symbol. The continuous but in steps. After each step, the knob plate (B). Proceed step by step until the desired load position is reached. For lighter loads, extract the knob (4mm indicated by the “-” symbol. After each step, the knob plate (B). Proceed step by step until the desired load position is reached. After adjusting the load, check that the ba length: the movement must not be limited by the complete winding of the spring. Check the stroke more than once and according to different speeds. After adjusting the load, check that the balancer cord can move freely along its heavier loads within the load capacity accepted, anticlockwise, indicated by the “+” symbol. The adjustment is not . After each step, the knob must go back into contact with roceed step by step until the desired load position is reached. mm) and grip it tightly. Turn it clockwise, ” symbol. After each step, the knob must go back into contact with roceed step by step until the desired load position is reached.
4mm
Note: a reduction in the ability of the balancer to hold the hanging lo to break. Do not operate the arm with the balancer, and contact Mountz for tool maintenance or replacement options. a reduction in the ability of the balancer to hold the hanging load might mean that the drum spring is about ad might mean that the drum spring is about
For ATS-40 (balancer 9323MZ) & ATS
TS-80 (balancer 9322MZ) models
A bushing was added to the tool balancer to safeguard its integrity from incorrect use when unloading the spring. This bushing makes it impossible to unload the spring using a wrench. The only way to unload it is through an appropriate lever foreseen by the instruction manual. To allow the tool balancer to operate heavier loads within the load capacity accepted, use spanner wrench to turn knob anticlockwise, identi desired load position is reached. heavier loads within the load capacity accepted, use anticlockwise, identified by the “+” symbol. Proceed until the tool balancer to safeguard its integrity from incorrect use when
For lighter loads, press on the end of the sp the “-” symbol. Proceed until the desired load position is reached. symbol. Proceed until the desired load position is reached.
press on the end of the spring and turn it clockwise, identified by
After adjusting the load, check that the balancer cord can move freely along its length: the movement must not be limited by the complete more than once and according to different speeds. Note: a reduction in the ability of the balancer to hold the hanging load might mean that the drum spring is about to break. Do not operate the arm with the balancer, Mountz for tool maintenance or replacement options. drum spring is about to break. Do not operate the arm with the balancer, and contact movement must not be limited by the complete winding of the spring. Check the stroke
Tool Balancer Inspection The balancer must be visually inspected regularly (e.g. once at each work shift). Specifically, check the state of the suspensions, the fixing screws and self of the hooks and the cable. Also, check the presence an cap on the adjustment system. Specifically, check the state of the suspensions, the fixing screws and self-locking systems (if used), the condition Also, check the presence and correct fit of the red high-visibility impact monitoring locking systems (if used), the condition visibility impact monitoring Regarding rejection criteria (cable replacement), refer to ISO 4309:2017 to check the cables. Check that the rope’s movement is smooth and that it does not make any Do not lubricate the balancer with flammable or volatile fluids Do not remove any labels. Replace any damaged labels. The balancer must be inspected at least once a year by skilled, authorized personnel. heck that the rope’s movement is smooth and that it does not make any strange noises. th flammable or volatile fluids els. Replace any damaged labels. he balancer must be inspected at least once a year by skilled, authorized personnel.
SILICON VALLEY HEADQUARTERS 1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292 1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292-2214 | Fax: (408) 292-2733 | mountztorque.com
7
Made with FlippingBook flipbook maker