TuffCam ™ Swing Clamps and Arms
Top Flange Swing Clamp
Single And Double Acting n Three cams for accurate arm positioning, smoother rotation and lower per cam surface contact pressure. n Patented ball seat for improved rotary function, cam follower contact and reduced dynamic and static friction. n Fluorocarbon wipers are standard for improved coolant compatibility. Standard swing is 90°; swing angles of less than 90° require Swing Restrictors. Swing angles greater than 90° are special order products. n To avoid cylinder damage and preserve warranty, use recommended flow rate limits and time calculations at the start of Section C. n Same mounting envelope as standard VektorFlo ® Metric Swing Clamps. n Tungsten Carbide ball material for strength and wear. n Arm clocking feature is at the start of Section C. n Arms sold separately – see the end of this section. Top flange TuffCam ™ swing clamps can be either manifold mounted or standard plumbed. Optional In-Port Flow Control is a meter-in device with reverse free flow check valve. Optional In-Port Sequence valve is a sequencing device with reverse free flow check valve.
C-3
U.S. Patent Nos. 6,886,820 7,032,897
ILMV414601 REV H SWING CLAMP PLUNGER SHOWN IN THE EXTENDED LH CAM POSITION SINGLE ACTING DOUBLE ACTING
Specifications
Port X Depth for Optional In-Port Valves****
Piston Area ( cm 2 ) Retract
Vertical Clamp Stroke ** (mm)
Oil Capacity*** (cm 3 )
Total Stroke (Swing + Vertical) (mm)
Cylinder Capacity* (kN)
Model No.
Swing Direction
Extend Retract
Single Acting (S/A) Cylinders, actuated hydraulically 1 direction, spring returned.
41-4602-11 Right Left 41-4605-11 Right 41-4602-12 41-4605-12 Left 41-4611-11 Right
2
5.5
14
0.63
N/A
0.92
G1/8 x 15.16
4.9
8
20
1.90
N/A
3.82
G1/8 x 15.16
11.6
13
29.5
4.04
N/A
11.9
G1/4 x 18.72
41-4611-12
Left
Double Acting (D/A) Cylinders, actuated hydraulically both directions.
41-4602-21 Right Left 41-4605-21 Right 41-4602-22 41-4605-22 Left 41-4611-21 Right
2
5.5
14
0.63
2.3
0.92
G1/8 x 15.16
4.9
8
20
1.90
7.8
3.82
G1/8 x 15.16
11.6
13
29.5
4.04
23
11.9
G1/4 x 18.72
41-4611-22
Left
WARNING! Never allow swing arm to contact workpiece or fixture during arm rotation. * Cylinder capacities are listed at 350 bar (35 MPa) maximum operating pressure, with a standard length VektorFlo ® arm installed. Minimum operating pressure is 52 bar (5.2 MPa) for single acting, 35 bar (3.5 MPa) for double acting. The clamping force is adjustable by varying the hydraulic system pressure. To determine the approximate output force for your application, divide the cylinder capacity shown above by 350, and multiply the resultant number times your system operating pressure to obtain the approximate clamping force for your application. (Actual force will vary slightly due to internal cantilever loading, friction loss and/or return springs.) ** To allow for workpiece height variations, it is recommended that the vertical travel be set to about 50% of the vertical stroke. *** To ensure maximum service life and trouble-free operation, restrict fluid flow per table at the start of Section C. **** In-Port valves require the use of manifold mount ports.
© Vektek December 2021
Inside US 1-800-992-0236
www.vektek.com
Made with FlippingBook - Online catalogs