TuffCam ™ Swing Clamps and Arms
Low Profile Magnetic Position Sensing
Low Profile Magnetic Position Sensing Swing Clamps n Available for use on both 22 kN and 33 kN double acting TuffCam™ Low Profile Swing Clamps. n Remove suffix - PS - and refer to the base model assembly part number for all other dimensions. n Sensors sold separately. n Sensor mounting housing is concentric to plunger shaft. n For use with Double Acting clamps only. n Arm clocking feature is compatible with all standard Vektek arms. Standard swing is 90°; swing angles of less than 90° require Swing Restrictors. Swing angles greater than 90° are special order products. Optional In-Port Flow Control is a meter-in device with reverse free flow check valve. Optional In-Port Sequence valve is a sequencing device with reverse free flow check valve. 46-2297-00 PNP Position Sensing Kit includes: 29-7001-00 Sensor and 27-6424-00 Cord set 46-2297-01 NPN Position Sensing Kit includes: 29-7001-01 Sensor and 27-6424-00 Cord set Sensor Feature: - Normally Open Contact - LED Indicator Light
C-18
- 10 to 30 VDC operating range - 3 Watt Maximum Contact Rating - ≤ 0.8 ms Switch-off time - ≤ 1.0 ms Switch-on time
U.S. Patent Nos. 6,886,820 7,032,897
The use of NPN or PNP is determined by the type of control unit to which the sensor is connected. One Sensor is required for each sensing position.
BN
1 4 3
BN BK BU
1 4 3
NPN
+
+
BK
BU
-
-
PNP
Model No. 46-2297-01 Schematic
Model No. 46-2297-00 Schematic
Low Profile Magnetic Position Sensing System Model No. Clamp Swing Direction Cylinder Capacity (kN) A (mm) Port X Depth for Optional In-Port Valves*
TuffCam ™ Bottom Flange (D/A) clamps, hydraulic retract and extend
41-4222-21-PS 41-4222-22-PS
Right
Left 41-4222-25-PS Straight 41-4233-21-PS Right Left 41-4233-25-PS Straight 41-4233-22-PS
22
65.5 G1/4 x 18.72
T-Slot for sensor (radial orientation is controllable in 15 increments)
33
65.5 G1/4 x 18.72
TuffCam ™ Top Flange (D/A) clamps, hydraulic retract and extend
41-4622-21-PS 41-4622-22-PS
Right
Left 41-4622-25-PS Straight 41-4633-21-PS Right Left 41-4633-25-PS Straight 41-4633-22-PS
22
65.5 G1/4 x 18.72
44.5
33
65.5 G1/4 x 18.72
6 A
TuffCam ™ Bottom Flange Long Stroke (D/A) clamps, hydraulic retract and extend
25.5
41-4222-26-PS 41-4222-27-PS
Right
Left
22
81.5 G1/4 x 18.72
41-4222-28-PS Straight 41-4233-26-PS Right 41-4233-27-PS Left 41-4233-28-PS Straight
Approx. 38 cm Sensor
Approx. 5 Meter Cordset ILMV414608 REV E
33
81.5 G1/4 x 18.72
TuffCam ™ Top Flange Long Stroke(D/A) clamps, hydraulic retract and extend
41-4622-23-PS 41-4622-24-PS
Right
Left 41-4622-26-PS Straight 41-4633-23-PS Right Left 41-4633-26-PS Straight 41-4633-24-PS
22
81.5 G1/4 x 18.72
33
81.5 G1/4 x 18.72
* In-Port Valves require the use of manifold mount ports.
www.vektek.com
Outside US+1-913-365-1045
© Vektek December 2021
Made with FlippingBook - Online catalogs