VersaCam™ Swing Clamps and Arms
n Available in four capacities from 2 kN to 22 kN at 350 bar (35 MPa). Standard models swing is 90° with swing angles of less than 90° available using restrictors. Swings of more than 90° are special order products. To avoid cylinder damage and preserve warranty, use recommended flow rate limits and time calculations at the start of Section C. n Arm clocking feature is compatible with all standard Vektek arms. n Arms sold separately – see end of this section. Porting is all on the top of the cylinder body for easy access (bottom unclamp porting is available), no need to modify fixtures or reroute tubing to access cylinder end to unclamp. Vent port with bronze filter gives the cylinder a place to "breathe" and helps keep chips from drawing past wipers. Hardened V-cam tracks resist damage and give you a built in extra cam or straight line option should you accidentally damage one. Specify left, right or straight cam, and we will preset the swing when you order. Single And Double Acting Threaded Body Specifications
C-21
U.S. Patent No. 7,032,897
DOUBLE ACTING SWING CLAMP PLUNGER SHOWN IN THE EXTENDED LH CAM POSITION SINGLE ACTING
ILMV150106 REV J
Specifications
Total Stroke (Swing + Vertical) (mm)
Effective Piston Area (cm 2 )
Oil Capacity*** (cm 3 )
Vertical Clamping Stroke** (mm)
Cylinder Capacity* (kN)
Model No.
Swing Direction
Body Thread
Retract
Extend Retract
Single Acting (S/A) Cylinders, actuated hydraulically 1 direction, spring returned.
41-5002-11 Right 41-5002-12 Left 41-5002-15 Straight 41-5005-11 Right 41-5005-12 Left 41-5005-15 Straight 41-5011-11 Right 41-5011-12 Left 41-5011-15 Straight 41-5022-11 Right 41-5022-12 Left 41-5022-15 Straight 41-5002-21 Right 41-5002-22 Left 41-5002-25 Straight 41-5005-21 Right 41-5005-22 Left 41-5005-25 Straight 41-5011-21 Right 41-5011-22 Left 41-5011-25 Straight 41-5022-21 Right 41-5022-22 Left 41-5022-25 Straight
6 6
2
14.5
M28 x 1.5
0.63
N/A
0.92
14.5
8 8
4.9
20
M38 x 1.5
1.90
N/A
3.82
20 13 13
11.6
29.5
M48 x 1.5
4.04
N/A
11.9
29.5
16 16
22
42
M65 x 1.5
7.60
N/A
32
42 Double Acting (D/A) Cylinders, actuated hydraulically both directions.
6 6
2
14.5
M28 x 1.5
0.63
2.3
0.92
14.5
8 8
4.9
20
M38 x 1.5
1.90
7.8
3.82
20 13 13
11.6
29.5
M48 x 1.5
4.04
23
11.9
29.5
16 16 42
22
42
M65 x 1.5
7.60
65.4
32
WARNING! Never allow swing arm to contact workpiece or fixture during arm rotation. * Cylinder capacities are listed at 350 bar (35 MPa) maximum operating pressure, with a standard length VektorFlo ® arm installed. Minimum operating pressure is 52 bar (5.2 MPa) for single acting, 35 bar (3.5 MPa) for double acting. The clamping force is adjustable by varying the hydraulic system pressure. To determine the approximate output force for your application, divide the cylinder capacity shown above by 350 (35MPa), and multiply the resultant number by your system operating pressure to obtain the approximate clamping force for your application. (Actual force will vary slightly due to internal cantilever loading, friction loss and/or return springs.) ** To allow for workpiece height variations, it is recommended that the vertical travel be set to about 50% of the vertical stroke. *** To ensure maximum service life and trouble-free operation, restrict fluid flow per table on page C-20.
© Vektek December 2021
Inside US 1-800-992-0236
www.vektek.com
Made with FlippingBook - Online catalogs