VersaCam™ Swing Clamps and Arms
Top Flange/Manifold Mount Specifications
Single And Double Acting Available in capacities from 2 kN to 11.6 kN at 350 bar (35 MPa) pressure. Easy to use, just bolt in place and plumb or use the easy-to-make manifold pattern to eliminate external plumbing. Can be either manifold mounted or standard plumbed using standard fittings. Single piece body and mounting give a rigid installation, no threads to rock around or additional mounting hardware to buy. To avoid cylinder damage and preserve warranty, use recommended flow rate limits and time calculations in Section C. Standard models swing is 90° swing angles of less than 90° readily available using restrictors. Swings of more than 90° are special order products. n Arm clocking is compatible with all standard Vektek arms. Arms sold separately – see end of this section. Optional In-Port Flow Control is a meter-in device with reverse free flow check valve. Optional In-Port Sequence valve is a sequencing device with reverse free flow check valve.
C-25
U.S. Patent No. 7,032,897
DOUBLE ACTING SWING CLAMP PLUNGER SHOWN IN THE EXTENDED LH CAM POSITION SINGLE ACTING ILMV152300 REV N DOUBLE ACTING SWING CLAMP PLUNGER SHOWN IN THE EXTENDED LH CAM POSITION SINGLE ACTING DOUBLE ACTING SWING CLAMP PLUNGER SHOWN IN THE EXTENDED LH CAM POSITION SINGLE ACTING
ILMV152300 REV N
ILMV152300 REV N
Specifications
Piston Area ( cm 2 )
Port X Depth for Optional In-Port Valves****
Oil Capacity*** (cm 3 )
Vertical Clamping Stroke** (mm)
Cylinder Capacity* (kN)
Total Stroke (Swing + Vertical) (mm)
Model No.
Swing Direction
Retract Extend Retract
Single Acting (S/A) Cylinders, actuated hydraulically 1 direction, spring returned.
41-5602-13 Right
6 6
41-5602-14
Left
2
14.5
0.63 N/A 0.92 G1/8 x 15.16
41-5602-16 Straight 41-5605-13 Right
14.5
8 8
41-5605-14
Left
4.9
20
1.90 N/A 3.82 G1/8 x 15.16
41-5605-16 Straight 41-5611-13 Right
20 13 13
41-5611-14
Left
11.6
29.5
4.04 N/A 11.9 G1/4 x 18.72
41-5611-16 Straight
29.5 Double Acting (D/A) Cylinders, actuated hydraulically both directions.
41-5602-23 Right
6 6
41-5602-24
Left
2
14.5
0.63
2.3 0.92 G1/8 x 15.16
41-5602-26 Straight 41-5605-23 Right
14.5
8 8
41-5605-24
Left
4.9
20
1.90
7.8 3.82 G1/8 x 15.16
41-5605-26 Straight 41-5611-23 Right
20 13 13
11.6
29.5
4.04
23 11.9 G1/4 x 18.72
41-5611-24
Left
41-5611-26 Straight 29.5 WARNING! Never allow swing arm to contact workpiece or fixture during arm rotation. * Cylinder capacities are listed at 350 bar (35 MPa) maximum operating pressure, with a standard length VektorFlo ® arm installed. Minimum operating pressure is 52 bar (5.2 MPa) for single acting, 35 bar (3.5 MPa) for double acting. The clamping force is adjustable by varying the hydraulic system pressure. To determine the approximate output force for your application, divide the cylinder capacity shown above by 350 (35), and multiply the resultant number by your system operating pressure to obtain the approximate clamping force for your application. (Actual force will vary slightly due to internal cantilever loading, friction loss and/or return springs.) ** To allow for workpiece height variations, it is recommended that the vertical travel be set to about 50% of the vertical stroke. *** To ensure maximum service life and trouble-free operation, restrict fluid flow per table on page C-20. **** In-Port valves require the use of manifold mount ports.
© Vektek December 2021
Inside US 1-800-992-0236
www.vektek.com
Made with FlippingBook - Online catalogs