VersaCam™ Swing Clamps and Arms
Manifold/Bottom Flange Mount Dimensions
Single And Double Acting Available in sizes from 2 kN, to 11.6 kN at 350 bar (35 MPa) pressure. Simply the easiest to use manifold mount design on the market today. No precision installation holes, no precisely located ports, no special mounting hardware, only our special patented design give you that. Unique, bolt up, bolt down or standard ported "foot" design allows you the maximum flexibility in fixture design. To avoid cylinder damage and preserve warranty use recommended flow rate limits and time calculations. Standard models swing 90° with swing angles of less than 90° readily available using restrictors. Swings of more than 90° are special order products. Arm clocking feature is compatible with all standard Vektek arms.
C-27
U.S. Patent No. 7,032,897
Arms sold separately – see end of this section. Optional In-Port Flow Control is a meter-in device with reverse free flow check valve. Optional In-Port Sequence valve is a sequencing device with reverse free flow check valve. Easily installed using standard cap screws. The large base and one piece mounting give this clamp excellent rigidity.
DOUBLE ACTING SWING CLAMP PLUNGER SHOWN IN THE EXTENDED LH CAM POSITION SINGLE ACTING
ILMV152101 REV N
Specifications
Effective Piston Area (cm 2 )
Oil Capacity*** (cm 3 ) Extend Retract
Port X Depth for Optional In-Port Valves****
Vertical Clamping Stroke** (mm)
Total Stroke (Swing + Vertical) (mm)
Cylinder Capacity* (kN)
Model No.
Swing Direction
Retract
Single Acting (S/A) Cylinders, actuated hydraulically 1 direction, spring returned.
41-5202-13 Right 41-5202-14 Left 41-5202-16 Straight 41-5205-13 Right 41-5205-14 Left 41-5205-16 Straight 41-5211-13 Right 41-5211-14 Left 41-5211-16 Straight 41-5202-23 Right 41-5202-24 Left 41-5202-26 Straight 41-5205-23 Right 41-5205-24 Left 41-5205-26 Straight 41-5211-23 Right 41-5211-24 Left 41-5211-26 Straight
6 6
2
14.5
0.63
N/A 0.92 G1/8 x 15.16
14.5
8 8
4.9
20
1.90
N/A 3.82 G1/8 x 15.16
20 13 13
11.6
29.5
4.04
N/A 11.9 G1/4 x 18.72
29.6 Double Acting (D/A) Cylinders, actuated hydraulically both directions.
6 6
2
14.5
0.63
2.3 0.92 G1/8 x 15.16
14.5
8 8
4.9
20
1.90
7.8 3.82 G1/8 x 15.16
20 13 13
11.6
29.5
4.04
23 11.9 G1/4 x 18.72
29.5
WARNING! Never allow swing arm to contact workpiece or fixture during arm rotation. * Cylinder capacities are listed at 350 bar (35 MPa) maximum operating pressure, with a standard length VektorFlo ® arm installed. Minimum operating pressure is 52 bar (5.2 MPa) for single acting, 35 bar (3.5 MPa) for double acting. The clamping force is adjustable by varying the hydraulic system pressure. To determine the approximate output force for your application, divide the cylinder capacity shown above by 350 (35), and multiply the resultant number by your system operating pressure to obtain the approximate clamping force for your application. (Actual force will vary slightly due to internal cantilever loading, friction loss and/or return springs.) ** To allow for workpiece height variations, it is recommended that the vertical travel be set to about 50% of the vertical stroke. *** To ensure maximum service life and trouble-free operation, restrict fluid flow per table 1. **** In-Port valves require the use of manifold mount ports.
© Vektek December 2021
Inside US 1-800-992-0236
www.vektek.com
Made with FlippingBook - Online catalogs