Cylinders
Cartridge Mount Push/Pull
B
D
G
H THREAD
Q SPRING CAVITY
4X J SPANNER HOLE
A
P
2X R
2X K
F
L
C STROKE
M
E THREAD X DEPTH
2X K
2X S
2X N RETRACT FEED HOLE
ILS210104
REV F
*Install includes return spring for S/A operation.
2X P Q
F-17
*NOTE: Anti-rotation pins intended for hand installation of bolt only. Do not torque bolt against anti-rotation pins.
R
NOTE: FLEXIBLE HONING/ BALL HONING OF CAVITY IS STRONGLY RECOMMENDED.
BREAK EDGE OF 15 RAMP .010 MAX
B C .005
.005 A
FROM BOTTOM OF COUNTERBORE MINOR D.005 E F THREAD UN G MIN
H MIN
64
.005 A
K MIN
15 1
L MAX
J +.005 M -.000
45 5
.125 MIN
40
32
R.020 MAX
A .001 -A- N MAX
S/A BREATHER HOLE LOCATION D/A EXTEND FEED HOLE LOCATION
ILS210103 REV D
ILS210105 REV F
Cavity Dimensions Model No.
Cap. A B C D E F G H J* K L M N** P*** Q***R*** Cartridge Torque (ft. - lbs.) ****
Double Acting (D/A)
Cylinders, actuated hydraulically both directions.
21-0206-00 21-0206-01 21-0209-00 21-0209-01 21-0210-00 21-0210-01 21-0213-00 21-0213-01 21-0216-00
1,500 0.813 1.27 1.080 0.939 0.60 1-16 0.48 0.26 0.116 0.39 0.75 1.130 0.16 0.125 0.625 0.44 25
3,000 1.188 1.65 1.393 1.252 0.68 1 5/16-16 0.50 0.26 0.116 0.39 0.75 1.130 0.18 0.125 0.625 0.53 35
3,900 1.313 1.77 1.580 1.439 0.67 1 1/2-16 0.53 0.33 0.116 0.46 0.81 1.192 0.18 0.156 0.625 0.56 60
7,400 1.751 2.15 1.955 1.814 0.75 1 7/8-16 0.59 0.33 0.116 0.46 0.81 1.192 0.33 0.156 0.625 0.88 65
12,000 2.126 2.64 2.455 2.314 0.70 2 3/8-16 0.59 0.45 0.116 0.45 0.93 1.318 0.35 0.281 0.625 1.00 160
21-0216-01 21-0221-00 22,000 2.876 3.39 3.205 3.064 0.88 3 1/8-16 0.72 0.45 0.116 0.58 1.31 1.693 0.40 0.281 0.625 1.57 200
* The 15° and 45° features of the cavity can be formed using an SAE 12, reduced spot face cutter except on models 21-0206-00 and 21-0206-01 ** N is intended for S/A cylinders (only) to prevent interference with the return spring. For D/A operation the feed can be positioned anywhere in the bottom of the cavity. Install included return spring for S/A operation. Return spring and anti-rotate pins are included with cylinder. *** Features for use with anti-rotate pins. **** Lubricate O-Rings with grease prior to installation.
www.vektek.com
800-992-0236
© Vektek, January 2023
Made with FlippingBook - Online magazine maker