Work Supports / Fluid Advance
High Capacity 3 Bolt Base & Cartridge
Upgrade your 3 bolt base models with higher capacity cartridges! Normally retracted plungers do not interfere with part loading. Advance them with hydraulic pressure, exerting only spring force to bring the plunger into contact with your part. Hydraulic pressure then automatically sequences, “freezing” the plunger properly against the part. Available in 2000 or 4000 lb. capacity. Used units are fully factory refurbishable to like new condition if the support body is undamaged. Order with base or cartridge only. Ventless configuration and built in wipers protect the plunger movement from chips and debris. Up to 3.5X capacity of competitor’s version.
B-7
Uses Vektek’s BHC technology to guard against corrosion. n O-Ring face seal design makes machining cavities easier.
Standard SAE porting and alternate O-Ring manifold face seal is located in the base of the support for bolt down installation. The base can be removed for direct cartridge mounting.
ILS100729 REV E U.S. PATENT NO. 10,799,992
Available as complete assembly too!
Direct Replacement for Older Model
Support Capacity (lbs.)*
Contact Force (lbs.)
Base Dimensions (in.)
Retracted Height (in.)
Model No.
Mounting Style***
Stroke (in.)
Oil Capacity** (cu. in.)
Fluid Advance Work Supports, hydraulic pressure pushes a spring which lifts plunger, hydraulic pressure locks in place. 10-0706-10 10-0706-04 2000 Cartridge 1-6 0.25 N/A 2.14 10-0806-10 10-0806-05 SAE/Manifold 0.90 X 1.31 X 1.75 2.51
0.05
10-0706-16 10-0706-14 10-0806-16 10-0806-15 10-0708-10 10-0708-07 10-0808-10 10-0808-07 10-0708-16 10-0708-17 10-0808-16 10-0808-17
Cartridge
N/A
2.64
0.50
0.07
SAE/Manifold
0.90 X 1.31 X 1.75 3.01
Cartridge
N/A
2.85
0.25
0.12
SAE/Manifold
1.25 X 1.50 X 2.31 3.25
4000
3-10
Cartridge
N/A
3.35
0.50
0.15
SAE/Manifold
1.25 X 1.50 X 2.31 3.75
* Support capacities are listed at 5,000 psi maximum pressure. Support capacities for other pressures are shown in the fluid advance High Capacity and Part Present Sensing load capacity chart. ** Restrict flow rate to a maximum of 130 cu. in./minute. *** For cartridge mount models, see cavity dimensions drawings in this cat alog section. **** For complete dimensions, see fluid advance work support section (B) in the Precision Hydraulic Clamping Inch catalog.
NOTE: The maximum system back-pressure a fluid advance work support can overcome is 10 psi. Returning back-pressure greater than 10 psi may cause slow or failed retraction.
B
M
AD
C Stroke
AE
N
3X T
E
D
G Hex
J
Q
S
A Thread
R
P
AC
For proper sealing, mating surface must be flat within 0.003 in with a maximum 63 µ in. R a surface finish. All dimensions are in inches.
H
F
V Hex x W Thread
Z
AB
L
Y
AA°
K
X Pressure Port
Manifold face seal counterbore, for applicable model number. O-ring and plug supplied.
ILS100733 REV B
Dimensions Model No.
A B C D E
F G H J
K L
M N P Q
Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks. 10-0806-10 1-16 2.51 0.25 1.19
0.90 0.21 0.88 0.56 0.14 1.31 0.66 0.90 0.45 1.75 0.69
Model No. 10-0806-10 10-0806-16 10-0808-10 10-0808-16 10-0806-16 10-0808-10 10-0808-16
3.01 0.50 1.65 3.25 0.25 1.44 3.75 0.50 1.83
1 1/4-16
1.25 0.36 1.13 0.75 0.19 1.50 0.75 1.06 0.53 2.31 0.94
R S T
V
W
X
Y Z AA ˚
AB AC AD AE
5/16-18 X 0.20 3/8 -24 x 0.20
1.20 0.51 0.22 0.50
SAE 2 0.33 0.38 7 0.38 0.69 YES N/A
1.66 0.72 0.28 0.63 7/16-14 X 0.25 SAE 4 0.43 0.38 N/A N/A N/A N/A YES
© Vektek, July 2024
800-992-0236
www.vektek.com
Made with FlippingBook - Online magazine maker