Work Supports
Legacy Fluid Advance
Available in: 1,000, 2,500 and 4,000 lbs. Normally retracted plungers do not interfere with part loading. Advance them with hydraulic pressure, exerting only spring force to bring the plunger into contact with your part. Hydraulic pressure then automatically sequences, “freezing” the plunger properly against the part. Ventless configuration and built in wiper keeps chips and debris out, reducing the chance of plunger/sleeve sticking or binding. Stainless steel plunger and sleeve assemblies help guard against corrosion in most machining environments. Standard SAE porting and alternate O-Ring manifold face seal is located in the base of the support for bolt down installation. The base can be removed for direct cartridge mounting.
B-29
NOTE: The maximum system backpressure a fluid advance work support can overcome is 10 psi. Returning backpressure greater than 10 psi may cause slow or failed retraction.
1000 & 2500 lb.
4000 lb.
4000 lb.
1000 & 2500 lb. 4000 lb.
1000 & 2500 lb.
ILS100700 REV Q
ILS100700 REV Q
ILS100700 REV Q
Support Capacity (lbs)
Contact Force** (lbs)
Base Dimensions (in.)
Retracted Height (in.)
Oil Capacity** (cu. in.)
Model No.
Mounting Style***
Stroke (in)
Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks. 10-0706-04 1,000 Cartridge 1 - 6 0.25 N/A
2.12 2.62 2.51 3.01 2.83 3.33 3.25 3.75 2.85 3.25
0.08 0.09 0.16 0.17 0.12 0.14 0.19 0.21 0.59 0.65
10-0706-14 10-0806-05 10-0806-15 10-0708-07 10-0708-17 10-0808-07 10-0808-17 10-0715-06 10-0815-06
1,400 1,000 1,400 2,500 3,000 2,500 3,000
0.50 0.25 0.50 0.25 0.50 0.25 0.50
SAE/Manifold
1 - 6
0.90 X 1.31 X 1.75
Cartridge
3 - 10
N/A
SAE/Manifold
3 - 10
1.25 X 1.50 X 2.31
N/A
Cartridge
4,000
8 - 12
0.50
SAE/Manifold
0.99 X 2.88 X 3.19
* Support capacities are listed at 5,000 psi maximum operating pressure. Support capacities for other pressures must be determined by consulting the capacity graph on the next page. ** Restrict flow rate to a maximum of 130 cu. in./minute. *** For cartridge mount models, see cavity dimensions drawings in this catalog section.
Dimensions Model No.
A
B C D E
F
G H J
K L
M N P
Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks. 10-0806-05 1-16 2.51 0.25 1.17
0.90 0.21 0.88 0.62 0.14 1.31 0.66 0.90 0.45 1.75
10-0806-15 10-0808-07
3.01 0.50 1.67 3.25 0.25 1.35
1 1/4-16
1.25 0.36 1.13 0.81 0.19 1.50 0.75 1.06 0.53 2.31
10-0808-17 3.75 0.50 1.85 10-0815-06 2 1/4-16 3.25 0.50 1.57 0.99 0.50 2.00 1.50 0.19 2.88 1.44 2.06 1.03 3.19
© Vektek, July 2024
800-992-0236
www.vektek.com
Made with FlippingBook - Online magazine maker