VersaCam™ Swing Clamps
Features, Patented Design and Air Ordering
VersaCam™ Features Large ball and cam rotational mechanism assures the swing action. Standard swing is 90°; swing angles less than 90° require Swing Restrictors (Page C-32). Swings angles greater than 90° are special order products. The original “duck billed,” cross bolt locking, top cap screw arm design, as originated by Vektek, is highly recommended due to its low mass, versatility and ease of modification, see Section O. Special wipers and swept-line cylinder top help keep chips from packing and coolant contaminants from entering the operation. Vent port with bronze filter gives the cylinder a place to “breathe” and helps keep chips
n Will withstand swing interference better than other cam designs. n VersaCam™ swing clamp models have hardened V-cam tracks that resist damage and give you a built in extra cam (opposite swing direction) or straight line option should you accidentally damage one. Vektek changes the “state-of-the-art” in ball and cam Swing Clamps making them work better at reasonable prices. or “kick” loads which promote excessive scoring in many other brands. BHC™ gives a Rockwell 60C skin hardness. Hardened chrome alloy steel plungers run longer with less wear and drag than other brands. Proprietary seal designs reduce leakage and increase seal life for longer lasting, more dependable operations. and coolants from drawing past wipers (Unclamp port on double-acting models). Exclusive BHC™ (Black Hard Coating) on the cylinder bodies and rod bearing surface helps prevent leaks caused by scoring and scratching especially in the event of high side
C-26
Patented V-groove Cam Design V shaped design provides a tougher mechanism. The ball runs deep in the track eliminating cam to ball edge loading. Resists flow related damage better (Please follow recommended flow rates for longest Swing Clamp life) than other clamps. Lasts longer and will withstand operator induced “crashes” from improperly loaded parts with less damage. Provides planar rather than edge contact with the cam follower. Swing Clamp Flow Rate and Clamping Time
ILS150103 REV C SWING CLAMP "V" GROOVE
CLAMP POSITION
30º
VersaCam Swing Clamp TuffCam Swing Clamps Standard Arm Extended Arm Standard Arm Extended Arm Clamp Time (sec.) Flow (cu. in./ min.) Clamp Time (sec.) Flow (cu in./ min.) Clamp Time (sec.) Flow (cu. in./ min.) Clamp Time (sec.) Flow (cu. in./ min.)
45º
Cylinder Capacity (lbs.)
60º
90º
450
0.4 0.6 0.6 0.7
8
0.9 1.2 1.4 1.4
4
0.2 0.3
17 47
0.5 0.7 0.8 1.0
7
1100 2600 5000
23 73
12 31 84
20 54
Vektek Swing
0.4 109 0.5 235
168
117
Restrictors Page C-32
TuffCam Low Profile Swing Clamps Standard Arm Extended Arm Clamp Time (sec.) Flow (cu. in./ min.) Clamp Time (sec.) Flow (cu. in./ min.)
Cylinder Capacity (lbs.)
NOTE: Arm Length and Pressure Limitation Graphs are found in Section O.
5000 7500
0.5 0.5
155 251
1.0 1.0
78
Air Ordering Information Vektek offers the VektorAir™ line of pneumatic clamping devices and accessories, rated to run up to 250 psi. Call for a catalog. If you currently use our hydraulic models adapted for air, you may continue to do so; contact our sales office for air ordering information.
126 ILS150108 REV J
- For upreach and double arms, use extended arm flows and times. - When using custom arms the extended arm flows and times are to be considered the limiting factor. - The actual time to position the clamp will vary by custom arm configuration and may require customer testing in specific application to establish limits.
www.vektek.com
800-992-0236
© Vektek, January 2023
Made with FlippingBook - Online magazine maker