Swing Clamps and Arms
Bottom Flange
Single And Double Acting Simply the easiest to use manifold mount design on the market today. No precision installation holes, no precisely located ports and no special mounting hardware needed. Only our special patented design gives you all that. Available in three sizes: 450, 1,100 and 2,600 lbs capacity. Unique, bolt up, bolt down or standard ported “foot” design allows you the maximum flexibility in fixture design. Can be manifold face sealed or fittings may be used in the top and bottom ports (SAE 2). n Arm clocking feature is compatible with all standard Vektek arms. n To avoid cylinder damage and preserve warranty use recommended flow rate limits and time calculations. Standard models swing 90° , swing angles of less than 90° readily available using restrictors. Swings of more than 90° are special order products. Optional in-port flow control is a meter-in device with reverse free flow check valve. Optional in-port sequence valve is a sequencing device with reverse free flow check valve.
C-35
Oil Capacity (cu. in.)****
Vertical Clamp Stroke (in)***
Port X Depth for Optional
Total Stroke (Swing + Vertical)
Effective Piston Area
Cylinder Capacity (lbs.)**
Standard Arm Length **
Model No.
Swing Direction
In-Port Valves *****
(sq. in.) Retract
Extend Retract
R, L S
Single Acting (S/A)
Cylinders, actuated hydraulically 1 direction, spring returned.
15-2105-03-R,L,S Right, Left, Straight 15-2109-04-R,L,S Right, Left, Straight 15-2113-04-R,L,S Right, Left, Straight
450 0.22 0.57 0.57 1,100 0.31 0.79 0.79 2,600 0.50 1.16 1.16 450 0.22 0.57 0.57 1,100 0.31 0.79 0.79 2,600 0.50 1.16 1.16
1.06 1.50 2.00
0.098 0.295 0.626
N/A 0.056 SAE 4 X .58 N/A 0.233 SAE 4 X .75 N/A 0.726 SAE 4 X .75
Double Acting (D/A)
Cylinders, actuated hydraulically both directions.
15-2205-03-R,L,S Right, Left, Straight 15-2209-04-R,L,S Right, Left, Straight 15-2213-04-R,L,S Right, Left, Straight
1.06 1.50 2.00
0.098 0.142 0.056 SAE 4 X .58 0.295 0.475 0.233 SAE 4 X .75 0.626 1.423 0.726 SAE 4 X .75
WARNING! Never allow swing arm to contact workpiece or fixture during arm rotation. ** Cylinder capacities are listed at 5,000 psi maximum operating pressure, with a standard length VektorFlo ® arm installed. Minimum operating pressure is 750 psi for single acting, 500 psi for double acting. The clamping force is adjustable by varying the hydraulic system pressure. To determine the approximate output force for your application divide the cylinder capacity shown above by 5,000, and multiply the resultant number by your system operating pressure to obtain the approximate clamping force for your application. (Actual force will vary slightly due to internal cantilever loading, friction loss and/or return springs.) *** To allow for piece part height variations, it is recommended that the vertical travel be set to about 50% of the vertical stroke. **** To ensure maximum service life and trouble-free operation, restrict fluid flow to the level indicated in the Clamp Time and Fluid flow Rate Chart for VersaCam. ***** In-Port Valves require the use of manifold mount ports.
Dimensions
Model No.*
A
B
C
D
E
F
G H
Single Acting (S/A) 15-2105-03-R,L,S
1.05 1.49 1.79 1.05 1.49 1.79
4.32 5.70 7.35 4.32 5.70 7.35
4.06 5.33 6.83 4.06 5.33 6.83
2.80 3.65 4.43 2.80 3.65 4.43
2.99 3.83 4.67 2.99 3.83 4.67
1.00 1.25 1.25 1.00 1.25 1.25
.66 .63 .63 .66 .63 .63
.438 .625 .875 .438 .625 .875
15-2109-04-R,L,S 15-2113-04-R,L,S
Double Acting (D/A) 15-2205-03-R,L,S
15-2209-04-R,L,S 15-2213-04-R,L,S
ALL MODELS ARE SHIPPED WITH REMOVABLE STEEL PLUGS INSTALLED. O-RING FACE SEALS PROVIDED. (SAE 2 PORTS) * MODELS 15-2105-01 (R, L, & S) and 15-2205-01 (R, L, & S) ARE MANIFOLD MOUNTABLE FROM THE BOTTOM SAE 2 PORT ONLY. ** ALL FIVE MOUNTING SCREWS MUST BE USED WHEN MANIFOLD MOUNTING, TO ASSURE A LEAK FREE O-RING SEAL.
© Vektek, July 2024
800-992-0236
www.vektek.com
Made with FlippingBook - Online magazine maker