Swing Clamps and Arms
Cartridge Mount
Single and Double Acting Simplified cavity design makes machining of pocket and installation easier. Eliminates the need for exposed plumbing, installs nicely in custom designed chip shedding fixtures. Uses SAE O-Ring mounting configuration. Bury deep in fixtures to reduce overall installed height and simplify design. n To avoid cylinder damage and preserve warranty use recommended flow rate limits and time calculations.
C-37
Arms sold separately, see end of section. Arms clocking feature is compatible with all standard Vektek arms.
SINGLE ACTING
DOUBLE ACTING
SWING CLAMP PLUNGER SHOWN IN THE EXTENDED LH CAM POSITION
ILS151100 REV J
Oil Capacity (cu. in.)****
Vertical Clamp Stroke (in)***
Total Stroke (Swing + Vertical)
Effective Piston Area
Swing Clamp Direction
Standard Arm Length
Cylinder Capacity (lbs.)**
SAE Body Thread
Model No.
(sq. in.) Retract
Extend Retract
R, L S
Single Acting (S/A)
Cylinders, actuated hydraulically 1 direction, spring returned.
15-1105-02-R,L,S Right, Left, Straight 15-1109-02-R,L,S Right, Left, Straight 15-1113-02-R,L,S Right, Left, Straight
450 0.22 0.57 0.57 1100 0.31 0.79 0.79 2600 0.50 1.16 1.16 450 0.22 0.57 0.57 1100 0.31 0.79 0.79 2600 0.50 1.16 1.16
1 1/16-12 1.06 1 5/8-12 1.50 1 7/8-12 2.00
0.098 0.295 0.626
N/A 0.056 N/A 0.233 N/A 0.726
Double Acting (D/A)
Cylinders, actuated hydraulically both directions.
15-1205-02-R,L,S Right, Left, Straight 15-1209-02-R,L,S Right, Left, Straight 15-1213-02-R,L,S Right, Left, Straight
1 1/16-12 1.06 1 5/8-12 1.50 1 7/8-12 2.00
0.098 0.142 0.056 0.295 0.475 0.233 0.626 1.423 0.726
WARNING! Never allow swing arm to contact workpiece or fixture during arm rotation. ** Cylinder capacities are listed at 5,000 psi maximum operating pressure, with a standard length VektorFlo ® arm installed. Minimum operating pressure is 750 psi for single acting, 500 psi for double acting. The clamping force is adjustable by varying the hydraulic system pressure. To determine the approximate output force for your application divide the cylinder capacity shown above by 5,000, and multiply the resultant number by your system operating pressure to obtain the approximate clamping force for your application. (Actual force will vary slightly due to internal cantilever loading, friction loss and/or return springs.) *** To allow for piece part height variations, it is recommended that the vertical travel be set to about 50% of the vertical stroke. **** To ensure maximum service life and trouble-free operation, restrict fluid flow to the level indicated in the clamp time and flow rates chart for Versacam.
Dimensions Model No.
A
B
C
D
E
F
G
H
Single Acting (S/A) 15-1105-02- R,L,S
1 1/16-12 1 5/8-12 1 7/8-12 1 1/16-12 1 5/8-12 1 7/8-12
4.25 5.66 7.32 4.25 5.66 7.32
4.00 5.31 6.80 4.00 5.31 6.80
2.12 2.68 3.15 2.12 2.68 3.15
0.83 1.13 1.49 0.83 1.13 1.49
0.63 0.94 1.25 0.63 0.94 1.25
0.49 0.65 0.55 0.49 0.65 0.55
0.438 0.625 0.875 0.438 0.625 0.875
15-1109-02- R,L,S 15-1113-02- R,L,S
Double Acting (D/A) 15-1205-02- R,L,S
15-1209-02- R,L,S 15-1213-02- R,L,S
*Single Acting Swing Clamps must be vented. Do not install in a blind hole
© Vektek, July 2024
800-992-0236
www.vektek.com
Made with FlippingBook - Online magazine maker