®
Thread Turning Toolholders
Internal Toolholders
Min. Bore Min. Bore
U-TYPE
D1
Min. Bore
F
F
L1
D
L
L
D
Min. Bore
F
D
L
Min Bore Diam.
Ordering Code Right Hand *SIR 0005 H06 *SIR 0007 K08 *SIR 0008 K08U *SIR 0010 H11 *SIR 0010 K11 *SIR 0013 L11 *SIR 0013 M16 *SIR 0016 P16 SIR 0020 P16 SIR 0025 R16 SIR 0032 S16 SIR 0040 T16 SIR 0050 U16 *SIR 0020 P22 SIR 0025 R22 SIR 0032 S22 SIR 0040 T22 SIR 0050 U22 SIR 0032 S22U SIR 0040 T22U SIR 0050 U22U SIR 0032 S27 SIR 0040 T27 SIR 0050 U27 SIR 0060 V27 SIR 0032 S27U SIR 0040 T27U SIR 0050 U27U SIR 0060 V27U *SIR 0050 U33U
Anvil Screw
Torx Key
RH Anvil
LH Anvil
L
D D1
L L1 F Insert Screw
6 8
12 16
5.1 6.0 100 12 4.3 S06 6.6 7.8 125 18 5.3 S08 7.3 9.0 125 21 6.6 S08
- - - - - -
K06 - K08 - K08 - K11 - K11 - K11 - K16 - K16 -
- - - - - - - -
8U 16
11 11 11 16 16 16 16 16 16 16 22 22 22 22 22
10 10 12 16 10 12 16 13 15 16 13 16 20 16 19 20 20 24 25 25 29 32 32 36 40 40 44 50 50 54 20 20 24 25 25 29 32 32 38 40 40 46 50 50 56
100 -
7.4 S11
125 25 7.4 S11 140 32 8.9 S11
150 32 10.2 S16S - 170 40 11.7 S16S -
170 - 200 - 250 - 300 - 350 - 170 - 200 - 250 - 300 - 350 - 250 - 300 - 350 - 250 - 300 - 350 - 400 - 250 - 300 - 350 - 400 - 350 -
13.7 S16 A16 K16 AI16 AE16 16.2 S16 A16 K16 AI16 AE16 19.7 S16 A16 K16 AI16 AE16 23.7 S16 A16 K16 AI16 AE16 28.7 S16 A16 K16 AI16 AE16 18.1 S22 A22 K22 AI22 AE22 21.6 S22 A22 K22 AI22 AE22 25.6 S22 A22 K22 AI22 AE22 30.6 S22 A22 K22 AI22 AE22 15.6 S22S - K22 - - 24.4 S22 A22 K22 AI22U AE22U 28.1 S22 A22 K22 AI22U AE22U 30.8 S22 A22 K22 AI22U AE22U 22.6 S27 A27 K27 AI27 AE27 26.6 S27 A27 K27 AI27 AE27 31.6 S27 A27 K27 AI27 AE27 36.6 S27 A27 K27 AI27 AE27 25.8 S27 A27 K27 AI27U AE27U 29.4 S27 A27 K27 AI27U AE27U 34.4 S27 A27 K27 AI27U AE27U 39.7 S27 A27 K27 AI27U AE27U
22U 32 32 38 22U 40 40 46 22U 50 50 57
27 27 27 27
32 32 40 40 40 48 50 50 58 60 60 68
27U 32 32 40 27U 40 40 48 27U 50 50 58 27U 60 60 68 33U 50 50 62
37.5 S33
-
K33 -
-
*Toolholders without anvil For LEFT HAND toolholders specify SI L instead of SI R Toolholders are made with a 1.5˚ Helix Angle. For other Helix Angles please see helix angle chart (page A04-7) in the technical section of this catalog. For “U” type inserts Tr, Acme, Stub Acme, see our software or contact main office for holder use.
A02-8
Made with FlippingBook - Online Brochure Maker