S554-3.0SX Recommended Milling Conditions
Side Milling
GR.4 /GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1 /GR.2 /GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.15 Nickel
Work Material
140
100
80
80
50
Vc m/min
RPM (min-1) 7432 5574 4459 3716 2787 2230
Feed (mm/min)
RPM (min-1) 5308 3981 3185 2654 1991 1593
Feed (mm/min)
RPM (min-1) 4247 3185 2548 2123 1593 1274
Feed (mm/min)
RPM (min-1) 4247 3185 2548 2123 1593 1274
Feed (mm/min)
RPM (min-1) 2654 1991 1593 1327
Feed (mm/min)
Code No.
Dc
S554-3.0SX-6 S554-3.0SX-8
6 8
1486 1338 1249 1189 1003
1359 1529 1427 1359 1019
849 764 713 679 573 510
849 892 815 764 637 510
531 438 382 345 279 255
S554-3.0SX-10 10 S554-3.0SX-12 12 S554-3.0SX-16 16 S554-3.0SX-20 20
995 796
892
917
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
Depth of Cut （ mm ）
ae:0.12D
ae:0.1D
ae:0.1D
ae:0.05D
ae:0.05D
High SpeedSide Milling
GR.4 /GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1 /GR.2 /GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.15 Nickel
Work Material
200
160
130
130
100
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1) 8493 6370 5096 4247 3185 2548
Feed (mm/min)
RPM (min-1) 6901 5176 4141 3450 2588 2070
Feed (mm/min)
RPM (min-1) 6901 5176 4141 3450 2588 2070
Feed (mm/min)
RPM (min-1) 5308 3981 3185 2654 1991 1593
Feed (mm/min)
Code No.
Dc
S554-3.0SX-6 S554-3.0SX-8
6 8
10617
2973 2548 2293 2123 1752 1529
1359 1274 1631 1699 1274 1223
1380 1242 1159 1104
828 828 994 897 725 662
637 478 382 319 239 191
7963 6370 5308 3981 3185
S554-3.0SX-10 10 S554-3.0SX-12 12 S554-3.0SX-16 16 S554-3.0SX-20 20
932 828
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
Depth of Cut （ mm ）
ae:0.1D
ae:0.05D
ae:0.1D
ae:0.05D
ae:0.05D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
18
Made with FlippingBook - Online Brochure Maker