S555-3.0SX Recommended Milling Conditions
Side Milling
GR.4 /GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1 /GR.2 /GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.15 Nickel
Work Material
140
100
80
80
50
Vc m/min
RPM (min-1) 7432 5574 4459 3716 2787 2230
Feed (mm/min)
RPM (min-1) 5308 3981 3185 2654 1991 1593
Feed (mm/min)
RPM (min-1) 4247 3185 2548 2123 1593 1274
Feed (mm/min)
RPM (min-1) 4247 3185 2548 2123 1593 1274
Feed (mm/min)
RPM (min-1) 2654 1991 1593 1327
Feed (mm/min)
Code No.
Dc
S555-3.0SX-6 S555-3.0SX-8
6 8
1188 1070 1100
1090 1225 1140 1090
680 610 570 545 460 410
680 715 650 610 510 410
425 350 305 275 225 200
S555-3.0SX-10 10 S555-3.0SX-12 12 S555-3.0SX-16 16 S555-3.0SX-20 20
950 800 715
815 735
995 796
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
Depth of Cut （ mm ）
ae:0.12D
ae:0.1D
ae:0.1D
ae:0.05D
ae:0.05D
High SpeedSide Milling
GR.4 /GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1 /GR.2 /GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.15 Nickel
Work Material
200
160
130
130
100
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1) 8493 6370 5096 4247 3185 2548
Feed (mm/min)
RPM (min-1) 6901 5176 4141 3450 2588 2070
Feed (mm/min)
RPM (min-1) 6901 5176 4141 3450 2588 2070
Feed (mm/min)
RPM (min-1) 5308 3981 3185 2654 1991 1593
Feed (mm/min)
Code No.
Dc
S555-3.0SX-6 S555-3.0SX-8
6 8
10617
2380 2040 1835 1700 1400 1225
1090 1020 1300 1360 1020
1100
660 660 795 720 580 530
510 380 305 255 190 150
7963 6370 5308 3981 3185
995 930 880 745 660
S555-3.0SX-10 10 S555-3.0SX-12 12 S555-3.0SX-16 16 S555-3.0SX-20 20
980
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
Depth of Cut （ mm ）
ae:0.1D
ae:0.05D
ae:0.1D
ae:0.05D
ae:0.05D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
20
Made with FlippingBook - Online Brochure Maker