S215TX
Recommended Milling Conditions
Side Milling
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
GR.15 Titanium
Work Material
120
120
80
65
60
65
120
30
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
S215TX-1 S215TX-1.5 S215TX-2 S215TX-2.5 S215TX-3 S215TX-4 S215TX-5 S215TX-6 S215TX-8 S215TX-10 S215TX-12 S215TX-16 S215TX-20
1 38220 459 38220 459 25480 306 20703 248 19110 76 20703 248 38220 459 9555 115 1.5 25480 510 25480 510 16987 340 13802 276 12740 76 13802 276 25480 510 6370 127 2 19110 573 19110 573 12740 382 10351 311 9555 96 10351 311 19110 573 4778 143 2.5 15288 612 15288 612 10192 408 6901 276 7644 107 8281 331 15288 612 3822 153 3 12,700 683 12,700 683 10,000 530 6,550 389 6,400 110 6,550 389 10,600 683 3,200 180 4 9,550 735 9,550 735 7,640 590 3,950 413 3,800 120 3,950 413 6,350 735 2,400 180 5 7,640 875 7,640 875 6,100 625 2,800 448 2,730 125 2,800 448 4,550 875 2,000 190 6 6,300 875 6,300 875 5,000 600 2,200 413 2,100 125 2,200 413 3,540 875 1,600 190 8 5,000 770 5,000 770 4,000 600 1,975 413 1,900 125 1,975 413 3,185 770 1,200 170 10 3,800 770 3,800 770 3,000 595 1,645 375 1,595 120 1,645 375 3,650 770 1,000 160 12 2,275 670 2,275 670 1,770 560 1,410 350 1,365 120 1,410 350 2,275 670 800 160 16 1,990 670 1,990 670 1,550 520 1,230 312 1,190 100 1,230 312 1,990 670 600 150
20 1,590 535 1,590 535 1,240 415
985
277
950
90
985
277 1,590 535
480
160
ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D
Depth of Cut （ mm ）
ae:0.2D ae:0.2D ae:0.2D ae:0.15D ae:0.1D ae:0.1D ae:0.2D ae:0.1D
Slotting
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
GR.15 Titanium
Work Material
120
120
80
65
60
65
120
30
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
S215TX-1 S215TX-1.5 S215TX-2 S215TX-2.5 S215TX-3 S215TX-4 S215TX-5 S215TX-6 S215TX-8 S215TX-10 S215TX-12 S215TX-16 S215TX-20
1 38220 306 38220 306 25480 204 20703 248 19110 76 20703 248 38220 459 9555 115 1.5 25480 357 25480 357 16987 238 13802 276 12740 76 13802 276 25480 510 6370 127 2 19110 459 19110 459 12740 306 10351 311 9555 96 10351 311 19110 573 4778 143 2.5 15288 489 15288 489 10192 326 6901 276 7644 107 8281 331 15288 612 3822 153 3 12,700 600 12,700 600 10,000 430 6,550 290 6,400 105 6,550 290 10,600 600 3,200 130 4 9,550 635 9,550 635 7,640 500 3,950 325 3,800 120 3,950 325 6,350 635 2,400 150 5 7,640 775 7,640 775 6,100 525 2,800 348 2,730 125 2,800 348 4,550 775 2,000 160 6 6,300 775 6,300 775 5,000 500 2,200 313 2,100 125 2,200 313 3,540 775 1,600 145 8 5,000 650 5,000 650 4,000 500 1,975 313 1,900 125 1,975 313 3,185 650 1,200 120 10 3,800 670 3,800 670 3,000 490 1,645 288 1,595 120 1,645 288 3,650 670 1,000 145 12 2,275 560 2,275 560 1,770 460 1,410 275 1,365 120 1,410 275 2,275 560 800 150 16 1,990 660 1,990 660 1,550 420 1,230 240 1,190 100 1,230 240 1,990 660 600 150
20 1,590 500 1,590 500 1,240 360
985
200
950
90
985
200 1,590 500
480
130
Depth of Cut （ mm ）
ap:0.5D ap:0.5D ap:0.5D ap:0.3D ap:0.1D ap:0.5D ap:0.5D ap:0.05D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
34
Made with FlippingBook - Online Brochure Maker